| bad dog racing |
Wed Feb 08, 2012 9:08 am |
|
March 3/4 works.
Build list:
Gasket Set
Flywheel Seal
Crankshaft
Crankshaft Pulley
Keys
Cam Gear
Spacer
Distributer Drive Gear
Snap Ring
Oil Slinger
Main Bearings
Rods
Rod Bearings
Case
Head Studs
Dowel Pins (case)
Lifters
Cam
Cam Bearings
Cam Plug
Case Washers and Nuts
Oil Pump
Pump Cover
Pistons and Cylinders (wrist pins, clips, rings, etc.)
Deflectors (under cylinder tin)
Barrel Spacers? (to set deck height and compression ratio)
Push Rod Tubes (new!)
Head Nuts and Washers
Push Rods
Rocker Assemblies
Valve Covers and Bails
Sump Plate, Screen, and Acorn Nuts
Flywheel (Dowel Pins and Shims)
Gland Nut
Distributer Drive and Shims
Breast Tin (Behind Pulley)
Oil Pressure Relief Valves, Springs, and Plugs
Oil Pressure Switch
Specialty Tools:
Deck Height Tool
Torch or Similar (to heat up crank Gears)
Lifter Clips
End Play Tool
Torque Wrench
Case Sealant
Oil (for assembly lube)
Piston Ring Compressor
Snap Ring Pliers
Wrist Pin Clip Pliers
Distributer Drive Puller
CC Kit for Heads
Calipers
What did I miss?
This list will get us to Longblock.
Are we going to complete? |
|
| norcalmike |
Wed Feb 08, 2012 9:18 am |
|
| im not sure if i will have my machining done and my new parts in time but i would like to watch. I can lend a hand and i have all the specialty tools to build other than a crank puller that i can bring and lend. |
|
| crofty |
Wed Feb 08, 2012 9:38 am |
|
| That sounds fun! |
|
| SurfCityRacing |
Wed Feb 08, 2012 9:55 am |
|
norcalmike wrote: im not sure if i will have my machining done and my new parts in time but i would like to watch. I can lend a hand and i have all the specialty tools to build other than a crank puller that i can bring and lend.
Word!
This is all about learning the methods of assembly, so we'll be focusing on the test engine rather than building several engines. Bring a note pad! Take notes! Let's learn together.
I don't have a ring compressor, or any way to measure end play. Those are the only things missing from the list. |
|
| crofty |
Wed Feb 08, 2012 11:11 am |
|
SurfCityRacing wrote: norcalmike wrote: im not sure if i will have my machining done and my new parts in time but i would like to watch. I can lend a hand and i have all the specialty tools to build other than a crank puller that i can bring and lend.
Word!
This is all about learning the methods of assembly, so we'll be focusing on the test engine rather than building several engines. Bring a note pad! Take notes! Let's learn together.
I don't have a ring compressor, or any way to measure end play. Those are the only things missing from the list.
I have 77mm, 83mm and 85.5mm compressors and the end play tool. If I can make it I'll bring 'em. |
|
| SCZ9-1-1 |
Wed Feb 08, 2012 3:14 pm |
|
| I'll try to show up in the afternoons. I'll have to go to work on the night of the 3rd. Location? |
|
| Johnny O |
Wed Feb 08, 2012 6:45 pm |
|
Jer.
Sounds great I will be there as for a table we can build if needed.
Honey Badgers do not give a shit anyways! |
|
| cruzwolf |
Wed Feb 08, 2012 8:27 pm |
|
Hey Jer,
you should do one of you Live Webcast of the event! |
|
| unclespanky |
Mon Feb 13, 2012 2:24 pm |
|
| Planning the first annual Big Sur campout. Open to 67 and earlier busses. Plenty of off road action and some of the best views on the Planet. Haven't set a date yet, but I'm working on it. |
|
| bad dog racing |
Mon Feb 13, 2012 4:54 pm |
|
unclespanky wrote: Planning the first annual Big Sur campout. Open to 67 and earlier busses. Plenty of off road action and some of the best views on the Planet. Haven't set a date yet, but I'm working on it.
Sounds like more Good Times! 8) |
|
| duhbrr |
Mon Feb 13, 2012 9:01 pm |
|
unclespanky wrote: Planning the first annual Big Sur campout. Open to 67 and earlier busses. Plenty of off road action and some of the best views on the Planet. Haven't set a date yet, but I'm working on it.
This sounds interesting. Got a rough idea of when this would take place? |
|
| unclespanky |
Mon Feb 13, 2012 10:13 pm |
|
| No firm dates just yet. I'd like to have it when Mr. Piercy is stateside. I've motorcycle camped at this location a number of times. Never fails to disappoint. |
|
| duhbrr |
Mon Feb 13, 2012 11:16 pm |
|
unclespanky wrote: I'd like to have it when Mr. Piercy is stateside.
I second that motion |
|
| unclespanky |
Wed Feb 15, 2012 9:28 am |
|
| Randy, I tried texting you with tech' tips for your kids Go-Kart engine. Ring me when you can. Anybody heard from Brian since he's been back? I get the feeling he's doing his own trip " fear and loathing " style. |
|
| cruzwolf |
Wed Feb 15, 2012 10:10 pm |
|
Hey Spankey,
sorry for not replying - I have been slammed with work and recovering from being sick. I got the 411 you sent - thanks. Tell us when the camp out is happening - I still got the off-road tires on my bus. |
|
| SurfCityRacing |
Thu Feb 16, 2012 4:54 pm |
|
Mine would be a touch different...
|
|
| Busryder |
Sat Feb 18, 2012 7:13 pm |
|
^^^ That is outstanding! ^^^^^
8) :lol: 8) :lol: 8)
And I'd love to take this class too... gotta be more fun than all them CogSci classes that I've grown so accustomed to. :P |
|
| unclespanky |
Sun Feb 19, 2012 5:23 pm |
|
| Jessie, was nice meeting you and you're 65 today I think I may have met your dad at Red Barn. Beautiful black bug in enclosed trailer? |
|
| unclespanky |
Tue Feb 21, 2012 8:14 pm |
|
| Another type II in the nieghborhood boyz!! A big SC type II welcome to Paul and his 64 splitty. :D |
|
| bad dog racing |
Wed Feb 22, 2012 9:33 am |
|
SurfCityRacing wrote: Let's do it March 3/4. I've got all necessary gear. Finding a clear table will be the greatest challenge!
I need an address of the location we will be doing this at.
I can bring tables. |
|
Powered by phpBB © 2001, 2005 phpBB Group
|