force3g |
Sat Oct 11, 2014 10:27 am |
|
I am replacing a cracked brake reservoir. The grommet had been completely dissolved from the brake fluid so I bout a new grommet from Bus Depot. As you can see in the photo the grommet is not going to fit into the brake fluid tube without splitting it. Has anyone had this issue? If so, what did you end up doing?
|
|
busdaddy |
Sat Oct 11, 2014 10:38 am |
|
A 70 doesn't use any grommet or seal there, later buses used a 211-611-833 C which still isn't that part you got, it looks like the seal where the tube goes into the master from here. |
|
force3g |
Sat Oct 11, 2014 10:42 am |
|
Do you have any suggestions to keep the reservoir from leaking fluid down the outside of the brake fluid tube? |
|
ricobiker |
Sat Oct 11, 2014 10:42 am |
|
i just replaced mine on my 76 westy. they did not look like that. i got mine from EIS parts.com. |
|
force3g |
Sat Oct 11, 2014 10:57 am |
|
Is this the correct seal?
http://www.eisparts.com/Merchant2/merchant.mvc? |
|
merlinj79 |
Sat Oct 11, 2014 11:06 am |
|
busdaddy wrote: it looks like the seal where the tube goes into the master from here.
That's what it is. |
|
merlinj79 |
Sat Oct 11, 2014 11:10 am |
|
force3g wrote: Is this the correct seal?
http://www.eisparts.com/Merchant2/merchant.mvc?
Bad link.
But that hose doesn't look like it uses a seal, just a tight fit over the nipple.
Since the hose is old it may be hard and not making a tight seal. Or the repro reservoir's nipple might be too small. You might need to replace it, or possibly use a hose clamp although that might just crack it. I don't know if teflon tape would hold up to brake fluid. |
|
Tcash |
Sat Oct 11, 2014 11:11 am |
|
http://www.eisparts.com/211611833C.html |
|
force3g |
Sat Oct 11, 2014 11:12 am |
|
How about this...
http://www.eisparts.com/211611833C.html |
|
71whitewesty |
Sat Oct 11, 2014 11:18 am |
|
I found that even with the correct seal that I had to use a heat gun to soften up the hose so that I could fit it together. |
|
airschooled |
Sat Oct 11, 2014 11:26 am |
|
force3g wrote: How about this...
http://www.eisparts.com/211611833C.html
This is what my '69 needed to quit weeping between the upper reservoir and tube. It's also on the low-milage survivors I've inspected. A factory plastic hose clamp (or black zip tie) with just the slightest clamp will function best. A white zip tie will be good to. Or a green one, or a pink one, though I'm partial to correct-ish when possible.
Robbie |
|
VWDruid |
Sat Oct 11, 2014 11:50 am |
|
got mine from WW https://www.wolfsburgwest.com/cart/DetailsList.cfm?ID=211611833C |
|
Tcash |
Sat Oct 11, 2014 11:58 am |
|
Hi asiab3
#9 Clip-refill line
Bus-boys=Master Cylinder Miscellaneous Parts
http://www.bus-boys.com/bb611.htm |
|
SGKent |
Sat Oct 11, 2014 4:36 pm |
|
I found all the brake grommets I needed and the reservoirs from Eric at Bug Haus. He had some genuine ones everyone else was out of. I think that weird special 1968 one was the only one he did not have last time I looked for someone.
The http://www.busdepot.com/211611833c part is the correct part. They turn to like gum over time but that helps them seal. On some years there is a special plastic VW clamp that goes around 100% without distorting the hose and it must be used.
http://bughaus.com/type214.htm |
|
Mike C |
Wed Oct 22, 2014 9:02 am |
|
Tcash wrote:
http://www.eisparts.com/211611833C.html
Does anyone know where to get the special plastic VW hose clamp that secures the hose to reservoir and master cylinder? I believe it is number 9 in the diagram.
Thanks |
|
curtis4085 |
Wed Oct 22, 2014 2:51 pm |
|
Mike C wrote: Tcash wrote:
http://www.eisparts.com/211611833C.html
Does anyone know where to get the special plastic VW hose clamp for the hose to reservoir and hose to master cylinder? I believe it is number 9 in the diagram.
Thanks
Email your request to [email protected]
Chris probably has one!! |
|
SGKent |
Wed Oct 22, 2014 2:59 pm |
|
Mike C wrote: Does anyone know where to get the special plastic VW hose clamp for the hose to reservoir and hose to master cylinder? I believe it is number 9 in the diagram.
Thanks
211 611 403
211-611-403
211611403
is the part number for #9. Google and consider making some calls would be my suggestion. |
|
Mike C |
Wed Oct 22, 2014 4:19 pm |
|
Thanks for the link and part number. I appreciate the help. I was able to get the stock hose and grommets--now all I need are the clamps. |
|
curtis4085 |
Wed Oct 22, 2014 4:26 pm |
|
Mike C wrote: Thanks for the link and part number. I appreciate the help. I was able to get the stock hose and grommets--now all I need are the clamps.
Justkampers has them new so I would assume busdepot has or could get the clamps as well. |
|
Powered by phpBB © 2001, 2005 phpBB Group
|