Author |
Message |
SpeedySpears Samba Member
Joined: June 18, 2014 Posts: 43 Location: Kansas City,Ks
|
Posted: Tue Jul 22, 2014 3:29 pm Post subject: Dual weber manifolds install |
|
|
Picked up some used weber manifolds for 44 idfs and was just wondering which manifold goes to which head. One manifold is labelled A the other B.
Thanks for the help! _________________ Rice eater. |
|
Back to top |
|
|
jfats808 Samba Member
Joined: December 10, 2007 Posts: 5022 Location: oahu hawaii
|
Posted: Tue Jul 22, 2014 4:09 pm Post subject: |
|
|
Ill usually put A on the 1-2 side and B 3-4. _________________ 2276 IDA's 86C 11-1 DD !
2017 48 Trijet DRLA's W125
Rockstar Suzuki wrote: |
You might as well put 10 year build in your bullshit sig, as it will NEVER run. Also your a dick |
You can always learn something new, even from a fool.
Check your oil levels routinely! |
|
Back to top |
|
|
SpeedySpears Samba Member
Joined: June 18, 2014 Posts: 43 Location: Kansas City,Ks
|
Posted: Tue Jul 22, 2014 4:12 pm Post subject: |
|
|
Sweet, thank you very much! _________________ Rice eater. |
|
Back to top |
|
|
Glenn Mr. 010
Joined: December 25, 2001 Posts: 76937 Location: Sneaking up behind you
|
|
Back to top |
|
|
SpeedySpears Samba Member
Joined: June 18, 2014 Posts: 43 Location: Kansas City,Ks
|
Posted: Tue Jul 22, 2014 6:51 pm Post subject: |
|
|
Glenn wrote: |
Are they ported? |
Yep port matched to my heads; btw never knew how much of a pain it would be to cut the manifold gaskets. Now I'm glad I had an extra set! _________________ Rice eater. |
|
Back to top |
|
|
Bajaman65 Samba Member
Joined: January 16, 2007 Posts: 469 Location: Borrego Springs
|
Posted: Wed Jul 23, 2014 11:44 am Post subject: |
|
|
SpeedySpears wrote: |
Glenn wrote: |
Are they ported? |
Yep port matched to my heads; btw never knew how much of a pain it would be to cut the manifold gaskets. Now I'm glad I had an extra set! |
Use a Dremel Tool with a sanding disc, it make shaping your gaskets a cinch. |
|
Back to top |
|
|
Hophead Samba Member
Joined: January 03, 2005 Posts: 940 Location: Chico,Ca
|
Posted: Thu Jul 24, 2014 10:26 pm Post subject: |
|
|
I would take and compare the gasket from each head to each manifold and see what lines up...... The usually A on side X and B on Side Y might not be correct.
Unless CNC ported there can be subtle variations to each port profile. The result could be less performance if they are not on the correct head. My hand ported heads from one of the major shops was different from side to side. I cleaned it up to be as close as possible but they are still not interchangeable from side to side.
Some will not see it as big deal and for some it isn't. I wanted to wring every pony out of my build so I bushed my mainfolds to take all the slop out. It makes checking and indexing the gaskets better. _________________ 70' Beetle Pan off Resto
2110cc
82 X 90.5
P&P 043 40x35.5
9.6-1 comp
FK-8
48 IDA |
|
Back to top |
|
|
SpeedySpears Samba Member
Joined: June 18, 2014 Posts: 43 Location: Kansas City,Ks
|
Posted: Fri Jul 25, 2014 12:57 pm Post subject: |
|
|
Thanks I'll check it out! _________________ Rice eater. |
|
Back to top |
|
|
|