Author |
Message |
midtravelmidengine Samba Member
Joined: August 06, 2009 Posts: 861 Location: Riverside, Ca
|
Posted: Wed Sep 24, 2014 3:47 pm Post subject: Anyone Heard of Anderson Heads? |
|
|
Friend bought a class 5 open baja and got a crate full of engine parts for it.
In the pile of parts was a pair of heads.
Castings : 311.101.376 G
they are ported and have "Anderson Heads" punched into the valve cover gasket surface just onder the intake ports.
Nice chamber shape too, i will get pictures loaded.
anyone have any info on them? _________________
modok wrote: |
And I know you don't know because if you did you would know the reason for my knowing you didn't. |
youngnstudly wrote: |
I just wasn't sure if I should recommend the 1/3 race cam, the 1/2 race cam, or the 5/8 race cam instead...guess it depends on how much of the race he wants to lead???
|
|
|
Back to top |
|
|
mark tucker Samba Member
Joined: April 08, 2009 Posts: 23937 Location: SHALIMAR ,FLORIDA
|
Posted: Wed Sep 24, 2014 4:11 pm Post subject: |
|
|
yup they make heads for top fuell,promods&alcoholl ....V8 stuff BAE. probably not what you have.... |
|
Back to top |
|
|
midtravelmidengine Samba Member
Joined: August 06, 2009 Posts: 861 Location: Riverside, Ca
|
Posted: Fri Sep 26, 2014 3:13 pm Post subject: |
|
|
Promised Photos:
all Porting & Chambers appear to be by hand _________________
modok wrote: |
And I know you don't know because if you did you would know the reason for my knowing you didn't. |
youngnstudly wrote: |
I just wasn't sure if I should recommend the 1/3 race cam, the 1/2 race cam, or the 5/8 race cam instead...guess it depends on how much of the race he wants to lead???
|
|
|
Back to top |
|
|
udidwht Samba Member
Joined: March 06, 2005 Posts: 3779 Location: Seattle, WA./ HB, Ca./ Shizuoka, Japan
|
Posted: Fri Sep 26, 2014 9:26 pm Post subject: |
|
|
midtravelmidengine wrote: |
Promised Photos:
all Porting & Chambers appear to be by hand |
Of all the places to place your name _________________ 1972 Westy Hardtop/Type-4 2056cc
96mm Biral AA P/C's~7.8:1CR
Headflow Masters New AMC 42x36mm heads w/Porsche swivel adjusters
71mm Stroke
73 Web Cam w/Web solids
Dual 40mm IDF Webers - LM-2 - 47.5 idles/125 mains/190 air corr./F11 tubes/28mm Vents - Float height 10.45mm/Drop 32mm
Bosch SVDA w/Pertronix module (7.5 initial 28 total @ 3400rpm)
Bosch W8CC plugs
Pertronix Flamethrower 40K coil
S&S 4-1 w/Walker QP 17862
3 rib 002 Trans
185R14 Hankook tires |
|
Back to top |
|
|
midtravelmidengine Samba Member
Joined: August 06, 2009 Posts: 861 Location: Riverside, Ca
|
Posted: Tue Sep 30, 2014 7:18 am Post subject: |
|
|
Bump!
No one?
I guess i just assumed if you spent the time to stamp your name into a set of heads it would be more than a one off garage job... _________________
modok wrote: |
And I know you don't know because if you did you would know the reason for my knowing you didn't. |
youngnstudly wrote: |
I just wasn't sure if I should recommend the 1/3 race cam, the 1/2 race cam, or the 5/8 race cam instead...guess it depends on how much of the race he wants to lead???
|
|
|
Back to top |
|
|
[email protected] Samba Member
Joined: August 15, 2002 Posts: 4394 Location: Brew City
|
|
Back to top |
|
|
mark tucker Samba Member
Joined: April 08, 2009 Posts: 23937 Location: SHALIMAR ,FLORIDA
|
Posted: Tue Sep 30, 2014 10:06 am Post subject: |
|
|
single spring, nice chambers pockets look ok too from what I can see. names are kinda like most everybdy's got one and some are one just because nobody recoggnasizes the name shouldent keep you from using a good peice if they do check out to be good for the intended app. kinda like saving $400 and putting it tward a crank/rod combo,or dvd/gps so you dont get lost with your girl out in the woods.......oops,might want to put a switch on the gps antenna
as for the heads new stainless valves atleast on the ex side. if they all look that good it was tuned pretty good. |
|
Back to top |
|
|
c21darrel Samba Member
Joined: January 22, 2009 Posts: 8211 Location: San Dimas
|
|
Back to top |
|
|
|