Author |
Message |
shepherdsond Samba Member
Joined: April 25, 2005 Posts: 439 Location: Bellingham, WA
|
|
Back to top |
|
|
fyrgrrl Samba Member
Joined: May 21, 2006 Posts: 396 Location: The Evergreen State
|
Posted: Mon Nov 17, 2014 3:35 pm Post subject: |
|
|
So Christopher...is there a tire out there that work for me with these wheels? Either my 1985 or 1987? Or is it all pie in the sky?
I gather that since you said they are a direct bolt on, I would not need special spacers or studs or lug nuts? _________________ 1987 Vanagon Westfalia (manual) - "Van Hildegaard"
1987 Vanagon Westfalia (auto)
1985 Vanagon GL 7-passenger van (auto) - "Blau Frau"
1985 Vanagon GL 7-passenger van (manual) - "Braunkuh"
1998 Subaru Legacy Outback (auto)
2003 Subaru Legacy L wagon (auto) |
|
Back to top |
|
|
Christopher Schimke Samba Member
Joined: August 03, 2005 Posts: 5391 Location: PNW
|
Posted: Mon Nov 17, 2014 3:42 pm Post subject: |
|
|
fyrgrrl wrote: |
So Christopher...is there a tire out there that work for me with these wheels? Either my 1985 or 1987? Or is it all pie in the sky?
I gather that since you said they are a direct bolt on, I would not need special spacers or studs or lug nuts? |
While there may be others, Nokian makes a 195/65R16 that would fit those wheels just fine and would not have the large effect on the gearing of the van that the 195/75R16s would have.
You can use the stock Vanagon steel wheel lugs with those wheels. _________________ "Sometimes you have to build a box to think outside of." - Bruce (not Springsteen)
*Custom wheel hardware for Audi/VW, Porsche and Mercedes wheels - Urethane Suspension Bushings*
T3Technique.com or contact me at [email protected] |
|
Back to top |
|
|
DontBeAfraid Samba Member
Joined: August 09, 2012 Posts: 94 Location: San Franfuckingcisco
|
Posted: Mon Nov 17, 2014 5:14 pm Post subject: Ronal R9 15" and Big Brake Kit compatability |
|
|
Hey,
I am considering buying a set of 15" Ronal R9s for my 2wd that are currently mounted on a syncro. I don't know what their offset is, nor do I know how wide they are. I understand that the mounting hardware necessary depends on the offset. I have asked the seller, but I thought I would ask about my main concern while I await his answers.
I plan on installing a big brake kit in the front eventually, and SC's system requires 13" diameter to mount. Is anyone running a big brake kit (from any vendor or homemade) and Ronal R9 15" wheels? If so, which one?
Thanks!
Dave _________________ Dave
1989 Westfalia 2.1 Four-on-the-Floor |
|
Back to top |
|
|
fyrgrrl Samba Member
Joined: May 21, 2006 Posts: 396 Location: The Evergreen State
|
Posted: Mon Nov 17, 2014 5:39 pm Post subject: |
|
|
Oh you're the man, Christopher. I actually drove up to Deming this past weekend and bought those tires and wheels for $300. I was having buyers remorse thinking I did a boneheaded buy. But I did OK, i guess.
Will any of my vans need lift springs or am I good with stock?
That was the last question, I promise...for sure....maybe.
Thanks for sharing your expertise. _________________ 1987 Vanagon Westfalia (manual) - "Van Hildegaard"
1987 Vanagon Westfalia (auto)
1985 Vanagon GL 7-passenger van (auto) - "Blau Frau"
1985 Vanagon GL 7-passenger van (manual) - "Braunkuh"
1998 Subaru Legacy Outback (auto)
2003 Subaru Legacy L wagon (auto) |
|
Back to top |
|
|
fyrgrrl Samba Member
Joined: May 21, 2006 Posts: 396 Location: The Evergreen State
|
Posted: Tue Nov 25, 2014 3:09 pm Post subject: |
|
|
Some pics of my 1985 Vanagon with the 16" OEM syncro wheels on the front. We got stopped mounting all the tires by the 2 bolts on the rear wheels. I thought there was only supposed to be one so got confused about what to do. I found out they both come out and then we can mount the wheels.
Here is a pic of the tire and wheel...with the 195/75R16 Vredestein tire...mounted on the front. I know Chris said that handling will not be ideal but we are just checking the fitment. Plus I need more clearance to get under the van to replace the old fuel filter with the newer style fuel filter.
Here's the side shot...with the 14" wheel on the back.
Cheers! _________________ 1987 Vanagon Westfalia (manual) - "Van Hildegaard"
1987 Vanagon Westfalia (auto)
1985 Vanagon GL 7-passenger van (auto) - "Blau Frau"
1985 Vanagon GL 7-passenger van (manual) - "Braunkuh"
1998 Subaru Legacy Outback (auto)
2003 Subaru Legacy L wagon (auto) |
|
Back to top |
|
|
bronsonarlo Samba Member
Joined: July 23, 2007 Posts: 5
|
Posted: Sat Nov 29, 2014 11:01 pm Post subject: AT Italia Wheels |
|
|
Hi All
I have been looking for a set of At Italia wheels for my Syncro Westy. I ended up finding a set on Craigslist. The only issue is the guy doesn't know the ET on the wheels, but he did send me these images. Anyone know what the numbers on the second image mean?
|
|
Back to top |
|
|
Christopher Schimke Samba Member
Joined: August 03, 2005 Posts: 5391 Location: PNW
|
Posted: Sun Nov 30, 2014 10:34 am Post subject: Re: AT Italia Wheels |
|
|
bronsonarlo wrote: |
Hi All
I have been looking for a set of At Italia wheels for my Syncro Westy. I ended up finding a set on Craigslist. The only issue is the guy doesn't know the ET on the wheels, but he did send me these images. Anyone know what the numbers on the second image mean?
|
If you can have the seller send you a couple of measurements off of the wheels, we can figure out the offset.
You will to the know the overall width of the wheel, which for a 6½" wide wheel will probably be somewhere between 7¼ and 7½ depending in the wheel. You will also need to know the distance between the wheel/hub mating surface and the edge of the inner rim lip. To accurately measure this. lay a straight edge across the rear of the wheel's inner rim lip (if tires are installed, make sure that the straight edge only touches the wheel and not the tire). Then measure from the straight edge down to the wheel/hub mating surface.
With those two measurements, we can determine the offset. _________________ "Sometimes you have to build a box to think outside of." - Bruce (not Springsteen)
*Custom wheel hardware for Audi/VW, Porsche and Mercedes wheels - Urethane Suspension Bushings*
T3Technique.com or contact me at [email protected] |
|
Back to top |
|
|
getsideways Samba Member
Joined: December 12, 2013 Posts: 10 Location: Australia
|
Posted: Thu Dec 04, 2014 5:52 pm Post subject: |
|
|
Hey wheel gods
I'm still not 100% sure on exactly what I need to get machined in order for some 16" Tiguan Baltimore rims to fit my Syncro.
From what I can gather I get the innermost part of the centre
bore machined to a diameter of 66.56mm and around 10mm depth?
I think I also need some small ball lug nuts, do I need open or closed, 19mm or 17mm? Will I need longer studs? |
|
Back to top |
|
|
Christopher Schimke Samba Member
Joined: August 03, 2005 Posts: 5391 Location: PNW
|
Posted: Thu Dec 04, 2014 6:02 pm Post subject: |
|
|
getsideways wrote: |
Hey wheel gods
I'm still not 100% sure on exactly what I need to get machined in order for some 16" Tiguan Baltimore rims to fit my Syncro.
From what I can gather I get the innermost part of the centre
bore machined to a diameter of 66.56mm and around 10mm depth?
I think I also need some small ball lug nuts, do I need open or closed, 19mm or 17mm? Will I need longer studs? |
Yes, the centerbore (big center hole) will need to be opened up. For use on a Syncro, you don't have to machine down very far.
My suggestion is to machine the centerbore to 66.56mm to a depth of 12mm. This will give the machinist a great target diameter and will also give you the opportunity to install 66.56mm to 57.1mm hubcentric rings should anyone ever decide to put them back onto a Tiguan.
I you truly don't care about making the wheels properly usable on a Tigaun again, you can simply ask the machinist to open the centerbore up to 67mm to a depth of 10mm. That will give you more than enough clearance and they are simple numbers to remember.
Yes, those wheels require small ball seat lug nuts. 17mm head open end or 19mm head closed end, the choice is yours since either on will work on those wheels.
You can use you existing studs, no need to change. _________________ "Sometimes you have to build a box to think outside of." - Bruce (not Springsteen)
*Custom wheel hardware for Audi/VW, Porsche and Mercedes wheels - Urethane Suspension Bushings*
T3Technique.com or contact me at [email protected] |
|
Back to top |
|
|
getsideways Samba Member
Joined: December 12, 2013 Posts: 10 Location: Australia
|
Posted: Thu Dec 04, 2014 6:15 pm Post subject: |
|
|
Christopher Schimke wrote: |
getsideways wrote: |
Hey wheel gods
I'm still not 100% sure on exactly what I need to get machined in order for some 16" Tiguan Baltimore rims to fit my Syncro.
From what I can gather I get the innermost part of the centre
bore machined to a diameter of 66.56mm and around 10mm depth?
I think I also need some small ball lug nuts, do I need open or closed, 19mm or 17mm? Will I need longer studs? |
Yes, the centerbore (big center hole) will need to be opened up. For use on a Syncro, you don't have to machine down very far.
My suggestion is to machine the centerbore to 66.56mm to a depth of 12mm. This will give the machinist a great target diameter and will also give you the opportunity to install 66.56mm to 57.1mm hubcentric rings should anyone ever decide to put them back onto a Tiguan.
I you truly don't care about making the wheels properly usable on a Tigaun again, you can simply ask the machinist to open the centerbore up to 67mm to a depth of 10mm. That will give you more than enough clearance and they are simple numbers to remember.
Yes, those wheels require small ball seat lug nuts. 17mm head open end or 19mm head closed end, the choice is yours since either on will work on those wheels.
You can use you existing studs, no need to change. |
Absolute legend!
Thanks for taking the time to respond. |
|
Back to top |
|
|
vw4life Samba Member
Joined: May 22, 2005 Posts: 144
|
Posted: Sun Dec 14, 2014 11:50 am Post subject: |
|
|
Here are my Audi 200 BBS wheels finally fitted!
Centerbores opened, 12 mm spacers and lugs/bolts from T3
|
|
Back to top |
|
|
wtcumby Samba Member
Joined: September 26, 2010 Posts: 114 Location: PORTLAND
|
Posted: Fri Dec 19, 2014 3:37 am Post subject: Re: 1991 Multivan |
|
|
Summers420us wrote: |
wtcumby wrote: |
18x8 cayenne wheels |
Any fitment issues? What about Speedo, does the cap still fit? Any rubbing? Spacers? Any other info? |
Upper A arms need clearanced
Speedo no issue
Center caps fit
Spacer/adapters required
Inner fender lip will need "rolled" or tire catches under certain circumstances
The ride is great and since they are all the same size (width and offset) they are rotatable. Also SUV load rated tires available which isn't the case for offset staggered (larger width in rear) _________________ I've got the vanagon fever |
|
Back to top |
|
|
masterzee2 Samba Member
Joined: January 09, 2014 Posts: 31 Location: Maryland
|
Posted: Wed Dec 31, 2014 8:09 am Post subject: Diamond Racing Steel Wheels |
|
|
Hey guys,
I was wondering if anyone knew if Diamond style Steel Drag/Racing Wheels could be fitted onto a late model Vanagon and if they'd work with a big brake kit? My bus is lowered on Weitec Springs & Koni Shocks if that helps at all. I'd most likely get 15" wheels if they fit. Any help would be much appreciated!
Example:
_________________ '91 Vanagon GL
'04 Jetta GLS |
|
Back to top |
|
|
Christopher Schimke Samba Member
Joined: August 03, 2005 Posts: 5391 Location: PNW
|
Posted: Mon Jan 05, 2015 6:57 am Post subject: Re: Diamond Racing Steel Wheels |
|
|
masterzee2 wrote: |
Hey guys,
I was wondering if anyone knew if Diamond style Steel Drag/Racing Wheels could be fitted onto a late model Vanagon and if they'd work with a big brake kit? My bus is lowered on Weitec Springs & Koni Shocks if that helps at all. I'd most likely get 15" wheels if they fit. Any help would be much appreciated!
|
You might call them to see if they do custom offsets, but they do not list any Vanagon-friendly offsets on their website. especially with a lowered van, I would be really careful with the offsets to avoid tire rubbing on the front.
I have no idea about the brake clearances. _________________ "Sometimes you have to build a box to think outside of." - Bruce (not Springsteen)
*Custom wheel hardware for Audi/VW, Porsche and Mercedes wheels - Urethane Suspension Bushings*
T3Technique.com or contact me at [email protected] |
|
Back to top |
|
|
ecsnsmb Samba Member
Joined: June 30, 2014 Posts: 11 Location: United States
|
Posted: Wed Jan 07, 2015 2:45 pm Post subject: |
|
|
Has anyone tried Sport Edition wheels? Found some 16x7, 35mm offset for a nice deal. Also going to run 86 Westy springs on my 89 Vanagon Tintop for a pinch more lift. Thanks for the help! |
|
Back to top |
|
|
steve_hoge Samba Member
Joined: October 22, 2009 Posts: 42 Location: Boulder CO
|
Posted: Wed Jan 07, 2015 5:40 pm Post subject: |
|
|
See a number of posts about Sport Edition wheels around this one in the Ultimate Wheel - Post Part 2:
http://www.thesamba.com/vw/forum/viewtopic.php?p=6435791#6435791
Sport Edition (Tire Rack house brand, mfg'd by Kosei) "F2" model, 5x112, 16x7 ET35, 20.6lbs. The through-width from the mounting face to bottom of the conical socket is 9.4mm (14.3mm to the top) - that's thin enough to accommodate stock Syncro studs.
$40/each from Craigslist, with Yokohama Geolandar A/T-S 215/70R16 tires, $125/each from Amazon.
|
|
Back to top |
|
|
luVWagn Samba Member
Joined: February 21, 2008 Posts: 1340 Location: Snoqualmie (WA)
|
|
Back to top |
|
|
steve_hoge Samba Member
Joined: October 22, 2009 Posts: 42 Location: Boulder CO
|
Posted: Fri Jan 09, 2015 11:26 am Post subject: |
|
|
luVWagn wrote: |
Steve, did you ever get info on load rating for the rims? Sweet deal! |
Not directly. These rims were originally intended for Mercedes E320 sedan (I think.)
The Tire Rack customer service agent I dealt with was as helpful as he could be - I believe he contacted Sport Edition to try and get this info. In response to his query whether the wheels had sufficient load rating for an '89 Syncro (the "O.E" or original equipment), he got this in response:
"The O.E. wheels had a very high load rating. These wheels are about 80 lbs per wheel lower on load rating than the O.E. tires. It's a very top heavy vehicle and that added stress requires a higher load rated wheel. None of our suppliers make a wheel with a high enough load rating to handle the additional stress for this fitment."
If you knew exact load rating for an '89 Syncro and an E320 you could do the math using this info. |
|
Back to top |
|
|
luVWagn Samba Member
Joined: February 21, 2008 Posts: 1340 Location: Snoqualmie (WA)
|
|
Back to top |
|
|
|