Author |
Message |
Schutterman Samba Member
Joined: August 18, 2011 Posts: 22 Location: Vancouver, canada
|
Posted: Tue Sep 01, 2015 10:33 pm Post subject: 64 Single Cab restoration |
|
|
Hey everyone well it's that time. I have finally got myself motivated enough to start with the restoration of my 64 single cab. First a little history. I bought the truck three years ago from a buddy right away I stuck an engine in it I fix the running gear and I drove around for two summers straight. This is what she looked like when I got her.
About July August last year I decided it was time to start getting it off the ground and on to a rotisserie. So I built my own with the use of engine stands. I was all geared up to start the resto last fall but I kind a got sidetracked. You know how that goes! LOL
Not too bad for a guy that tinkers at home.
So now we get to the present, I have began sourcing out metal from 1 concept in Calgary and with the help of my friend I have devised a plan of attack. You may know him he is a part of a VW club up in the greater Vancouver area, Joel Sanderson. He is been a real help in answering any questions I have and has give me the direction I need to restore this truck. First thing I'm doing is deal with the structural. So I started to cut out the rusted up cross braces and clean them up. I will be ordering the metal this week. I'll try to get some pictures up in the next few days. |
|
Back to top |
|
|
Schutterman Samba Member
Joined: August 18, 2011 Posts: 22 Location: Vancouver, canada
|
Posted: Tue Sep 01, 2015 10:46 pm Post subject: 64 single cab restoration |
|
|
I noticed I said 1 concept, I meant concept1. Oh and I will be picking up the parts there on Friday or Saturday. I'll be on my way out to Winnipeg from the West Coast to grab my new treasures that I found in the prairies a couple weeks ago, you can see pics on my gallery. |
|
Back to top |
|
|
kalymnos Samba Member
Joined: January 22, 2010 Posts: 112 Location: Hamburg/Germany
|
Posted: Wed Sep 02, 2015 12:32 am Post subject: |
|
|
Good luck with the resto, but I wouldn't trust that construction with the concrete blocks and motor stand. |
|
Back to top |
|
|
glideking Samba Member
Joined: February 02, 2013 Posts: 990 Location: California
|
|
Back to top |
|
|
Schutterman Samba Member
Joined: August 18, 2011 Posts: 22 Location: Vancouver, canada
|
Posted: Sun Sep 06, 2015 3:41 pm Post subject: 64 single cab restoration |
|
|
I probably should have posted a picture of the other side.
It's solid on those stands they hold a 1000 pounds each.
You can see I have a 4x4 taking the weight as well to help the stands from tipping. |
|
Back to top |
|
|
Schutterman Samba Member
Joined: August 18, 2011 Posts: 22 Location: Vancouver, canada
|
Posted: Thu Sep 24, 2015 10:41 pm Post subject: My first piece ever |
|
|
Got my first piece of metal in today. In fact it's the first body work I have ever done. I built a adjustable beam a couple years ago, but other then that that's it for fabricating!!!!! It's been slow. This is all new to me, I am a rookie in the fullest sense. But like so many of us that love this hobby, we are all up to the challenge and the learning curve. So please help me in anyway.
In the last week I got all the cutting and grinding done on one of the main cross trusses(not sure what to call them haha). Today more prep and finally tack it in place HELL YEH. Have to say I was pretty stoked once I saw all welded up.
Had a bit of a tough time figuring out the volts to wire speed. I used the calculator on the welder but I think because it is plug welding it had to be more heat and wire speed. Started to get the hang of it after about half way. Then it went pretty smooth. Gotta clean up the welds and then on to the next truss. |
|
Back to top |
|
|
nice dad Samba Member
Joined: July 25, 2013 Posts: 317 Location: Honolulu, HI
|
Posted: Fri Sep 25, 2015 4:35 pm Post subject: Re: My first piece ever |
|
|
Schutterman wrote: |
Got my first piece of metal in today. In fact it's the first body work I have ever done. I built a adjustable beam a couple years ago, but other then that that's it for fabricating!!!!! It's been slow. This is all new to me, I am a rookie in the fullest sense. But like so many of us that love this hobby, we are all up to the challenge and the learning curve. So please help me in anyway.
In the last week I got all the cutting and grinding done on one of the main cross trusses(not sure what to call them haha). Today more prep and finally tack it in place HELL YEH. Have to say I was pretty stoked once I saw all welded up.
Had a bit of a tough time figuring out the volts to wire speed. I used the calculator on the welder but I think because it is plug welding it had to be more heat and wire speed. Started to get the hang of it after about half way. Then it went pretty smooth. Gotta clean up the welds and then on to the next truss. |
Nice job on the welds. Welcome to the party! _________________ 1967 Single Cab |
|
Back to top |
|
|
Schutterman Samba Member
Joined: August 18, 2011 Posts: 22 Location: Vancouver, canada
|
Posted: Fri Oct 02, 2015 8:17 am Post subject: Cargo floor removal |
|
|
I decided to change my plan thanks to Glidking lol. Have to say since I started reading his thread last week the motivation and drive to do a full nice clean resto has come to the fore. Thanks Kurt and nice work on Funky!
The cargo floor had cancer here and there, I could have pieced new metal in there but it just won't look as nice as that Ugly Green stuff. Two nice clean panels that's definitely the way to go........so Chop chop!!
Off comes that ugly orange WW metal from Brazil that came with the truck. I guess the PO didn't do his research on who to buy from. It was a blessing cause some of those spot welds I did didn't take on the cross beam. I'll blame the metal from WW. What a newbie. Lol
So I have a question for you all. Now that I got most of the cargo floor cut out, what would be the best way to remove the cargo floor flanges at the back engine separation panel and rear wheel wells. All the metal in those areas is in good shape and I don't want to ruin any of those areas. I guess things can always be reshaped, but I want to know the cleanest and easiest way. Should I just drill out the welds, grind? Should I drill from the back? What side should I drill from? Should I just cut close to the flange then drill out welds, should I wait till I get the deck off, etc.
Any help would be appreciated |
|
Back to top |
|
|
Schutterman Samba Member
Joined: August 18, 2011 Posts: 22 Location: Vancouver, canada
|
Posted: Tue Nov 24, 2015 12:46 am Post subject: Re: 64 Single Cab restoration |
|
|
Well I been able to get a little metal removed since my last post. I now have the cargo floor, some top hats, cross braces, long side rocker, treasure chest rocker, some of the doglegs, and some of the cab floor removed.
I'll get some more pics in the next day or so. |
|
Back to top |
|
|
imtb Samba Member
Joined: October 27, 2013 Posts: 363 Location: st.l
|
Posted: Tue Nov 24, 2015 9:23 am Post subject: Re: 64 Single Cab restoration |
|
|
Looking good, a lot of single cab action going on right now. |
|
Back to top |
|
|
Schutterman Samba Member
Joined: August 18, 2011 Posts: 22 Location: Vancouver, canada
|
Posted: Tue Nov 24, 2015 10:05 pm Post subject: Re: 64 Single Cab restoration |
|
|
Such a unique vehicle and so well put together. What I love is the looks you get from everyone..... 👍 they are like WT.... is that!!!
Here are some pics of some other areas I've had to remove.
|
|
Back to top |
|
|
Schutterman Samba Member
Joined: August 18, 2011 Posts: 22 Location: Vancouver, canada
|
Posted: Tue Nov 24, 2015 10:27 pm Post subject: Re: 64 Single Cab restoration |
|
|
Enough destruction! I finally got my first piece of permanent metal in today! Was pretty stoked when I saw it all done. First ever patch in a never ending hobby. The passenger A pillar had a hole down near the dogleg.
Had to cut the hole way back to get something solid.
Ug those welds.......
Now that I got that done, it's on to the cut out piece on the dogleg......to be continued |
|
Back to top |
|
|
Rusties Samba Member
Joined: April 01, 2005 Posts: 141 Location: Bc canada
|
Posted: Wed Nov 25, 2015 10:34 am Post subject: Re: 64 Single Cab restoration |
|
|
Looking good Sean!
Keep it up! |
|
Back to top |
|
|
|