| Author |
Message |
walter kandetzki
Samba Member
Joined: June 02, 2003
Posts: 918
Location: Dillwyn, VA
|
 Posted: Wed Dec 04, 2013 7:32 pm Post subject: case no good? |
 |
|
| hi folks,i have a 1600 dual port engine and the engine has ALOT of play and I saw rear bearing moves forward if I pull on crank pulley...is the case is done or will maybe a line bore help it out?thanks |
|
| Back to top |
|
 |
sgmalt46
Samba Member
Joined: April 20, 2005
Posts: 1296
Location: south san francisco
|
| Posted: Wed Dec 04, 2013 7:40 pm Post subject: |
|
|
line bore and thrust cut will fix it. you will need a machine shop check it out for ya.
_________________
55 deluxe 23 window bus
64 crew cab
55 rag top beetle
66 beetle
71 square back (sold) ! good luck with it Henry!
46 beetle 552nd royal army service corps CCG |
|
| Back to top |
|
|
75smith
Samba Member
Joined: July 09, 2011
Posts: 2275
Location: NH
|
| Posted: Wed Dec 04, 2013 7:42 pm Post subject: |
|
|
line bore may help, or it may not, need to measure for sure
_________________
My 1975 Beetle Build Updated 8-21-12
My engine build |
|
| Back to top |
|
|
nsracing
Samba Member
Joined: November 16, 2003
Posts: 9481
Location: NOVA
|
| Posted: Fri Dec 06, 2013 7:07 am Post subject: |
|
|
Geeze, Walt! If the bearings are moving in the case don't you think you will need a fresh linebore?
Come up my way and I will linebore that thing for you. |
|
| Back to top |
|
|
[email protected]
Samba Member
Joined: August 03, 2002
Posts: 12785
Location: Salt Lake City, Utah
|
| Posted: Fri Dec 06, 2013 8:38 am Post subject: |
|
|
bearing moving fore/aft = thrust cut
_________________
It's just advice, do whatever you want with it!
Please do NOT send me Private Messages through the Samba PM System (I will not see them). Send me an e-mail to john at aircooled dot net
"Like" our Facebook page at
http://www.facebook.com/vwpartsaircoolednet
and get a 5% off code for use on one order for VW Parts ON OUR PARTS STORE WEBSITE, vwparts.aircooled.net |
|
| Back to top |
|
|
mcmscott
Samba Member
Joined: March 12, 2010
Posts: 4858
Location: sanger ca
|
| Posted: Fri Dec 06, 2013 8:48 am Post subject: |
|
|
And if the thrust is pounded too far it equals junk case, hope fully this is not the case(pun intended)
_________________
There are no stupid questions, only stupid people,
68 Ghia
67 T-1
65 Notch
02 Mexican beetle
74 Thing
15 Long travel rail
07 Nomad
05 f-250 |
|
| Back to top |
|
|
mark tucker
Samba Member
Joined: April 08, 2009
Posts: 23937
Location: SHALIMAR ,FLORIDA
|
| Posted: Fri Dec 06, 2013 9:45 am Post subject: |
|
|
| or have some crafty feller install a thrust incert...or type 4 thrust!! or a great bonfire for christmass. |
|
| Back to top |
|
|
|
