Author |
Message |
cdog334 Samba Member
Joined: April 20, 2010 Posts: 53 Location: louisiana
|
Posted: Sat Apr 09, 2011 9:22 pm Post subject: Napoleon hat threaded plates |
|
|
I was in the process of removing my floor pans. The four frame head bolts gave me some trouble to remove. I had one snap off when almost all the way out.
My question is where can i find replacement threaded plates or should i just replace the nepoleons hat all together.
I noticed a lot of rust comming out the frame head bolt holes,but the hat looks to be solid......
One other question. I see that WW sells it apprear to be the whole frame head section. would it be easier to change out the whole section or just the hat?
Thanks |
|
Back to top |
|
|
RareAir Samba Member
Joined: May 11, 2002 Posts: 14576 Location: 18 miles North of the border
|
Posted: Sat Apr 09, 2011 9:41 pm Post subject: |
|
|
Make your own threaded plates. All it is is a piece of rectangular metal with two holes that are threaded to accept the bolt. Why go through all the trouble R&R'ing the front of the pan (Napolean hat) _________________ 1947 Typ 11a
1954 Typ 117
1956 Typ 151
1959 Typ 117
1959 Typ 265
1961 356B
1966 Typ 151
1966 Typ 241 |
|
Back to top |
|
|
finefettle Samba Member
Joined: October 13, 2006 Posts: 699 Location: Shelburne,Vermont
|
Posted: Sun Apr 10, 2011 12:47 pm Post subject: |
|
|
The plates (you can easily make up) are in the body not the frame head. Just repair the metal that needs to be repaired on the Napolean Hat. |
|
Back to top |
|
|
beetlenut Samba Member
Joined: May 27, 2009 Posts: 2983 Location: RI
|
Posted: Sun Apr 10, 2011 12:56 pm Post subject: |
|
|
The plates you are talking about:
Don't live in the napoleons hat, they live above that in the front firewall, the only way to access them is from the side of the firewall:
The four frame head bolts go through the napoleons hat, through the front tab of the heater channel bottom plate, and then into the front fire wall floating captive nut plate. _________________ scrapyards are for quitters
---------------------------------------
Wetstuff wrote: |
... I spend more time shaking it than directing it?! I get a pretty decent blast for 8sec. then have to shake it again. |
- Words to live by right there!
My 74 Super rebuild thread: http://www.thesamba.com/vw/forum/viewtopic.php?p=6507104#6507104 |
|
Back to top |
|
|
smkn_vw Samba Member
Joined: August 22, 2004 Posts: 809
|
Posted: Sun Apr 10, 2011 4:37 pm Post subject: |
|
|
Those plates float in a cage within the heater channel, removing the bottom plate of the heater channel will give you access to the plates. I cleaned up my plates when I worked on my heater channels, I'll see if I can find a photo. _________________ "So didja?" -Bob Hoover
Last edited by smkn_vw on Sun Apr 10, 2011 4:43 pm; edited 1 time in total |
|
Back to top |
|
|
smkn_vw Samba Member
Joined: August 22, 2004 Posts: 809
|
Posted: Sun Apr 10, 2011 4:42 pm Post subject: |
|
|
Here you go . . . I think it just bends (no welds) to get the plate in and out. I still have nightmares of drill bits and sparks after some of the work I did on my heater channels.
_________________ "So didja?" -Bob Hoover |
|
Back to top |
|
|
beetlenut Samba Member
Joined: May 27, 2009 Posts: 2983 Location: RI
|
Posted: Mon Apr 11, 2011 1:21 pm Post subject: |
|
|
smkn_vw wrote: |
Those plates float in a cage within the heater channel, removing the bottom plate of the heater channel will give you access to the plates. I cleaned up my plates when I worked on my heater channels, I'll see if I can find a photo. |
Not sure if different years had different arrangements on the captive nut plate, but on supers the nut plate was in the front firewall. The pic below from Bugs'n'Pugs shows several layers of metal before you get to the captive nut plate. The first layer of metal is the framehead bottom plate. The next layer of metal to the left is the heater channel bottom plate. The next layer of metal under that, to the left, is the bottom of the front firewall. Then the captive nut plate sits inside that.
This pic shows the bottom of the front firewall with the framehead bottom plate, and the heater channel bottom plate cut away.
This was Bugs'n'Pugs front firewall thread discussing this. This thread really cleared up some things for me, as I'm making those captive nut plates right now for this job.
http://www.thesamba.com/vw/forum/viewtopic.php?t=300571&highlight=front+firewall _________________ scrapyards are for quitters
---------------------------------------
Wetstuff wrote: |
... I spend more time shaking it than directing it?! I get a pretty decent blast for 8sec. then have to shake it again. |
- Words to live by right there!
My 74 Super rebuild thread: http://www.thesamba.com/vw/forum/viewtopic.php?p=6507104#6507104 |
|
Back to top |
|
|
cdog334 Samba Member
Joined: April 20, 2010 Posts: 53 Location: louisiana
|
Posted: Mon Apr 18, 2011 2:46 pm Post subject: frame head bolts |
|
|
Thank to all for the information. I realize i will have to cut a slit to remove these floating nut plates. I was surprised how much my car resembled the pictures. I plan on getting some navel jelly to treat this area. The use some type of anti sieze to make it easier on the next guy.
I have found that htese are included with new heater channels.
Thank you to all who replied you have been a great help ! |
|
Back to top |
|
|
|