Author |
Message |
tootype2crazy Samba Member
Joined: October 08, 2007 Posts: 1276 Location: St. Louis Missouri
|
Posted: Thu Jun 07, 2012 12:15 pm Post subject: Big ole bumper dent on bus - what to do? |
|
|
I am doing all my own body work (first time on any car). I am stumped as to how to go about getting this dent out. Its thick metal that is hard to move. The area gets covered by a bumper so it doesn't need to look pretty. It just has to be the right general shape. Any suggestions?
_________________ air-cooled or nothing for me
1978 Sunroof Deluxe Bus (daily driver)
1978 Transporter (mom's, making into a camper)
1970 Single Cab 2.1 turbo/EFI 6 Rib, 78 front beam, vanagon backing plates on rear (project)
2001 GTI VR6 (wife's) |
|
Back to top |
|
|
tootype2crazy Samba Member
Joined: October 08, 2007 Posts: 1276 Location: St. Louis Missouri
|
|
Back to top |
|
|
Mike Fisher Samba Member
Joined: January 30, 2006 Posts: 17970 Location: Eugene, OR
|
Posted: Thu Jun 07, 2012 1:31 pm Post subject: |
|
|
Heat from a cutting torch w/heating tip on it & Big slip joint pliers/hand sledge etc. _________________ https://imgur.com/user/FisherSquareback/posts
69 FI/AT square Daily Driver
66 sunroof,67,70,71,71,71AT,72,72AT,73 Parts
two 57 oval ragtops sold
'68 Karmann Ghia sold
Society is like stew. If you don't keep it stirred up you end up with a lot of scum on the top! - Russ_Wolfe/Edward Abbey |
|
Back to top |
|
|
tootype2crazy Samba Member
Joined: October 08, 2007 Posts: 1276 Location: St. Louis Missouri
|
Posted: Thu Jun 07, 2012 3:11 pm Post subject: |
|
|
Ok I know I gotta heat it up, but how do I get a grip on it. Should I weld a nail in there to grab onto? I am new to body work so any explicit instructions would be greatly appreciated. _________________ air-cooled or nothing for me
1978 Sunroof Deluxe Bus (daily driver)
1978 Transporter (mom's, making into a camper)
1970 Single Cab 2.1 turbo/EFI 6 Rib, 78 front beam, vanagon backing plates on rear (project)
2001 GTI VR6 (wife's) |
|
Back to top |
|
|
Mike Fisher Samba Member
Joined: January 30, 2006 Posts: 17970 Location: Eugene, OR
|
Posted: Thu Jun 07, 2012 5:27 pm Post subject: |
|
|
It would be much easier to buy a good used piece and weld it on your car. _________________ https://imgur.com/user/FisherSquareback/posts
69 FI/AT square Daily Driver
66 sunroof,67,70,71,71,71AT,72,72AT,73 Parts
two 57 oval ragtops sold
'68 Karmann Ghia sold
Society is like stew. If you don't keep it stirred up you end up with a lot of scum on the top! - Russ_Wolfe/Edward Abbey |
|
Back to top |
|
|
tootype2crazy Samba Member
Joined: October 08, 2007 Posts: 1276 Location: St. Louis Missouri
|
Posted: Thu Jun 07, 2012 6:01 pm Post subject: |
|
|
That is what I was thinking too, the only problem is I live in an area where buses are rare. To have a good one shipped to me would be prohibitively expensive because this piece is no doubt very heavy and quite large. I wonder if I could get a boneyard out west to just cut off the portion that is damaged and then I can frankenstein it up. _________________ air-cooled or nothing for me
1978 Sunroof Deluxe Bus (daily driver)
1978 Transporter (mom's, making into a camper)
1970 Single Cab 2.1 turbo/EFI 6 Rib, 78 front beam, vanagon backing plates on rear (project)
2001 GTI VR6 (wife's) |
|
Back to top |
|
|
Mike Fisher Samba Member
Joined: January 30, 2006 Posts: 17970 Location: Eugene, OR
|
Posted: Thu Jun 07, 2012 6:10 pm Post subject: |
|
|
Ask Avery's Aircooled in WA for the section you need. Google them for their info. _________________ https://imgur.com/user/FisherSquareback/posts
69 FI/AT square Daily Driver
66 sunroof,67,70,71,71,71AT,72,72AT,73 Parts
two 57 oval ragtops sold
'68 Karmann Ghia sold
Society is like stew. If you don't keep it stirred up you end up with a lot of scum on the top! - Russ_Wolfe/Edward Abbey |
|
Back to top |
|
|
tootype2crazy Samba Member
Joined: October 08, 2007 Posts: 1276 Location: St. Louis Missouri
|
|
Back to top |
|
|
|