Author |
Message |
AllRad Samba Member
Joined: December 04, 2016 Posts: 64 Location: Pacific Northwest
|
Posted: Sun Oct 03, 2021 8:53 am Post subject: Is this a sign of a bad coolant pressure cap? |
|
|
My 14 month old plastic coolant tank ruptured along the seam a couple of months ago. After being sticker shocked by the price of the aluminum tanks, I went for a replacement plastic tank. New cap too. I assume I will go aluminum after my next big problem
Be that as it may, after a couple of 300 miles drives, I noticed that coolant adds to the overflow tank -- as it should. But after sitting for a day (or two, or a week) it stays in the overflow tank at levels that are well above the "MAX" line.
On two occasions I've drained the excess from the overflow tank and manually poured it back into the pressure tank. But coolant consistently flows back into the overflow tank and stays there.
Could this be a sign that the cap is not allowing the coolant to return when cold? Is some other issue? I never had this happen before. I did add the Vanistan heater valve that includes a bleeder tube thing. I am honestly not sure how it bleeds air, but could that play a role?
Cheers!
|
|
Back to top |
|
|
djkeev Samba Moderator
Joined: September 30, 2007 Posts: 32598 Location: Reading Pennsylvania
|
|
Back to top |
|
|
crazyvwvanman Samba Member
Joined: January 28, 2008 Posts: 9923 Location: Orbiting San Diego
|
Posted: Sun Oct 03, 2021 9:30 am Post subject: Re: Is this a sign of a bad coolant pressure cap? |
|
|
After a long drive when the level goes high on the license door tank you need to IMMEDIATELY inspect the main pressure tank for air before any cooling has taken place.
If there is air in the main tank then that points to something else going on than simply the cap not allowing the coolant to flow back in.
Mark
AllRad wrote: |
.....Be that as it may, after a couple of 300 miles drives, I noticed that coolant adds to the overflow tank -- as it should. But after sitting for a day (or two, or a week) it stays in the overflow tank at levels that are well above the "MAX" line. ..... |
|
|
Back to top |
|
|
jb20thae Samba Member
Joined: August 10, 2021 Posts: 117 Location: West
|
Posted: Sun Oct 03, 2021 11:00 am Post subject: Re: Is this a sign of a bad coolant pressure cap? |
|
|
Holy mackerel your van looks clean! |
|
Back to top |
|
|
hdenter Samba Member
Joined: October 14, 2008 Posts: 2753 Location: San Luis Obispo, CA
|
Posted: Sun Oct 03, 2021 11:25 am Post subject: Re: Is this a sign of a bad coolant pressure cap? |
|
|
Check the hose between the cap and the overflow. It should have hose clamps on both ends. If it is frayed, just barely cracked or not tightly sealed, the fluid makes it into the overflow tank but, when the engine cools and should suck back the coolant, it sucks in air instead.
Hans _________________ '79 triple white convertible bug
'84 sunroof vanagon
'85 weekender |
|
Back to top |
|
|
0to60in6min Samba Member
Joined: November 27, 2006 Posts: 3416 Location: OR & CA (Oregon/California)
|
Posted: Sun Oct 03, 2021 11:25 am Post subject: Re: Is this a sign of a bad coolant pressure cap? |
|
|
Besides the eventual air leak... you could test the blue cap...with engine cold, coolant cold, remove the blue cap and blow at the tube... you should hear a sound and then you can rule out a defective blue cap. |
|
Back to top |
|
|
?Waldo? Samba Member
Joined: February 22, 2006 Posts: 9752 Location: Where?
|
Posted: Sun Oct 03, 2021 11:55 am Post subject: Re: Is this a sign of a bad coolant pressure cap? |
|
|
crazyvwvanman wrote: |
After a long drive when the level goes high on the license door tank you need to IMMEDIATELY inspect the main pressure tank for air before any cooling has taken place.
If there is air in the main tank then that points to something else going on than simply the cap not allowing the coolant to flow back in.
|
^^^This.^^^
If you start a decent drive with the pressure tank full and the burp tank at a proper level and after the drive, the level is high in the burp tank AND there is air in the pressure tank, then you have a more serious issue (e.g. combustion leak into the coolant) that has nothing to do with the pressure cap, burp tank or the hose between the two. |
|
Back to top |
|
|
Wildthings Samba Member
Joined: March 13, 2005 Posts: 50338
|
Posted: Sun Oct 03, 2021 12:00 pm Post subject: Re: Is this a sign of a bad coolant pressure cap? |
|
|
Since you have a new tank you may be able to see bubbles continuously moving through the tank, if so this is a very bad sign. These engines are known to experience head stud failure which will lead to a leak of combustion gases passed the cylinder sealing rings into the water jacket. |
|
Back to top |
|
|
pdm777 Samba Member
Joined: August 06, 2012 Posts: 348 Location: Clovis, CA
|
Posted: Sun Oct 03, 2021 3:42 pm Post subject: Re: Is this a sign of a bad coolant pressure cap? |
|
|
I see two issues looking at your photo.
1) that clamp on the hose to your pressure tank cap
looks crooked and therefore loose in your photo.
2) The pressure tank should be full to the top
at ALL TIMES. there should be no air in the top
of the tank,
As we can see, it is sucking air back into the press. tank,
but not coolant. Most likely your hose from tank to overflow
has cracks, loose clamps etc.
NEW HOSE, double check clamps are -tight-. _________________ 1990 Westy Full Camper
Last edited by pdm777 on Sun Oct 03, 2021 3:46 pm; edited 1 time in total |
|
Back to top |
|
|
djkeev Samba Moderator
Joined: September 30, 2007 Posts: 32598 Location: Reading Pennsylvania
|
|
Back to top |
|
|
AtlasShrugged Samba Member
Joined: October 30, 2008 Posts: 1605 Location: Decatur, Ga. USA
|
Posted: Sun Oct 03, 2021 8:03 pm Post subject: Re: Is this a sign of a bad coolant pressure cap? |
|
|
pdm777 wrote: |
I see two issues looking at your photo.
1) that clamp on the hose to your pressure tank cap
looks crooked and therefore loose in your photo.
2) The pressure tank should be full to the top
at ALL TIMES. there should be no air in the top
of the tank,
As we can see, it is sucking air back into the press. tank,
but not coolant. Most likely your hose from tank to overflow
has cracks, loose clamps etc.
NEW HOSE, double check clamps are -tight-. |
I must disagree about the pressure tank needing to be completely full. It should be topped up to a MAX mark, clearly visible on the original OEM pressure tanks. If you have an aftermarket tank fill it to the seam or look for the MAX mark.
All Euro plastic pressure tanks have an air gap in them, the Vanagon is no exception. Why would the Vanagon design be any different with its huge coolant capacity?
If you persist in filling the pressure tank 100% full with no air gap you will have a busted pressure tank sooner or later. Air is compressible. Coolant is not. A solid 15psi solid coolant slug all the time when hot without an air gap in the pressure tank will eventually cause it to fail.
The license plate overflow tank is just a safety reservoir for extreme temps or slow leaks.
Do a pressure test on the system and use an OEM VW pressure cap, not aftermarket. Part number 025121321B about $40 (yikes..but it is a good investment) _________________ 'Let's Go Brandon' |
|
Back to top |
|
|
?Waldo? Samba Member
Joined: February 22, 2006 Posts: 9752 Location: Where?
|
Posted: Sun Oct 03, 2021 8:52 pm Post subject: Re: Is this a sign of a bad coolant pressure cap? |
|
|
The min/max marks are on the burp tank at the license plate. There is no max mark on the pressure tank (in the engine compartment) as it should always be completely full of coolant. Sometimes when the system has been opened for work it takes a few heat cycles to purge all of the air out of the pressure tank but unless there is an issue, then after that initial purge, the pressure tank will always be completely full of coolant. The entire system pressure is regulated by the pressure cap and is designed to operate at 14-15psi without any 'air gap'. The license plate tank is used during every heat cycle to allow excess coolant (and any air that needs to purge) to flow out of the pressurized system when up to temp and to draw in coolant from the license plate tank each time the system cools. |
|
Back to top |
|
|
pdm777 Samba Member
Joined: August 06, 2012 Posts: 348 Location: Clovis, CA
|
Posted: Sun Oct 03, 2021 10:32 pm Post subject: Re: Is this a sign of a bad coolant pressure cap? |
|
|
thank you WALDO !!!
'bout
to have
a stroke. _________________ 1990 Westy Full Camper |
|
Back to top |
|
|
djkeev Samba Moderator
Joined: September 30, 2007 Posts: 32598 Location: Reading Pennsylvania
|
Posted: Mon Oct 04, 2021 1:36 am Post subject: Re: Is this a sign of a bad coolant pressure cap? |
|
|
AtlasShrugged wrote: |
pdm777 wrote: |
I see two issues looking at your photo.
1) that clamp on the hose to your pressure tank cap
looks crooked and therefore loose in your photo.
2) The pressure tank should be full to the top
at ALL TIMES. there should be no air in the top
of the tank,
As we can see, it is sucking air back into the press. tank,
but not coolant. Most likely your hose from tank to overflow
has cracks, loose clamps etc.
NEW HOSE, double check clamps are -tight-. |
I must disagree about the pressure tank needing to be completely full. It should be topped up to a MAX mark, clearly visible on the original OEM pressure tanks. If you have an aftermarket tank fill it to the seam or look for the MAX mark.
All Euro plastic pressure tanks have an air gap in them, the Vanagon is no exception. Why would the Vanagon design be any different with its huge coolant capacity?
If you persist in filling the pressure tank 100% full with no air gap you will have a busted pressure tank sooner or later. Air is compressible. Coolant is not. A solid 15psi solid coolant slug all the time when hot without an air gap in the pressure tank will eventually cause it to fail.
The license plate overflow tank is just a safety reservoir for extreme temps or slow leaks.
Do a pressure test on the system and use an OEM VW pressure cap, not aftermarket. Part number 025121321B about $40 (yikes..but it is a good investment) |
Hmmmm ........
So, have we been so uber concerned and anal about over heating that we swallowed the proverbial "KoolAid" of an absolutely full pressure tank?
I wonder ...... Have head gaskets been replaced because the coolant system has a small bubble of air in the tank?
Is it possible that the cooling system functions much like many engine oil dipsticks and prefers to operate just a smidgen below full?
If a bubble appears, or a slightly low level appears, should we just not top it off and continue to run with that bubble?
(Of course monitor it until it is proven to be at a constant "normal" level. )
Are we chasing rainbows by always wanting our pressure tank to always be 100% full?
Owners manual pages from my 1990 model year, but the photos used and the text seem to have remained the same for WBX years (at least back to 85 which is as far back as I looked at)
The text says...... only worry about the pressure tank level IF the low coolant light comes on.
Are we, the preachers of the absolutely full expansion tank gospel, wrong? ......
Dave _________________ Stop Dead Photo Links how to post photos
Ghia
http://www.thesamba.com/vw/forum/viewtopic.php?t=392473
Vanagon
http://www.thesamba.com/vw/forum/viewtopic.php?p=6315537#6315537
Beetle
https://www.thesamba.com/vw/forum/viewtopic.php?t=482968&highlight=74+super+vert |
|
Back to top |
|
|
Wildthings Samba Member
Joined: March 13, 2005 Posts: 50338
|
Posted: Mon Oct 04, 2021 3:31 am Post subject: Re: Is this a sign of a bad coolant pressure cap? |
|
|
djkeev wrote: |
Are we, the preachers of the absolutely full expansion tank gospel, wrong? ......
|
Experience shows that with everything working as per factory that if you have sufficient coolant within the system you will have either no bubble or only a minor one in the pressure tank. It is quite reasonable to just live with a smallish bubble and just let it disappear with usage as the system purges itself. If the bubble is large and/or increases with size over time, then you have a problem. |
|
Back to top |
|
|
4Gears4Tires Samba Member
Joined: October 08, 2018 Posts: 3028 Location: MD
|
Posted: Mon Oct 04, 2021 5:51 am Post subject: Re: Is this a sign of a bad coolant pressure cap? |
|
|
After replacing the coolant tanks, it can take awhile to work out some air bubbles. I had consistent air in the tank problems for two years after I put my van back together. The first issue was the rear heater, it was sucking in air at the valve, which I only discovered after it started leaking coolant. I removed that. Then I still couldn't get get a decent/consistent bleed until I installed the Vanistan Heater Valve Auto-bleed. https://intrepidoverland.com/shop/t3-vanagon-front-heater-valve/ I also bought an aluminum tank, but that didn't help me aside from peace of mind. Before the auto-bleed system I was messing with the coolant at least once a week, it was annoying. I also didn't realize it's possible to overfill the system, which will fill the burp tank. It's also possible that everything appears to be filled correctly and running well for months, but the first time you sit in stop and go traffic, the system will get a lot hotter and overfill the burp tank. If that happened, I rebled the system when all I needed to do was drain down the burp tank. I never had a problem bleeding the coolant over 15+ years working on BMWs, no idea what I was doing wrong here. Even bought a vacuum coolant filler, no dice. I usually topped the coolant off with a windshield washer reservoir, pump, and line through the radiator bleed port.
So, you have air in your coolant reservoir, which shouldn't be there. First step I would do is crack the bleed valve at your radiator, which you need to remove the grill for. Then, I would slightly untwist the coolant reservoir cap until all the air and a little bit of of coolant comes up. Drain the burp tank down to max. Then go for a 20+ minute drive and bring coolant with you. Does the air reappear? Does the burp tank get more coolant? You can try this ^ several times. If you're not making progress, I would reaaally consider the heater valve. _________________ '87 Syncro
Ferric Oxyhydroxide Superleggera Edition |
|
Back to top |
|
|
?Waldo? Samba Member
Joined: February 22, 2006 Posts: 9752 Location: Where?
|
Posted: Mon Oct 04, 2021 8:14 am Post subject: Re: Is this a sign of a bad coolant pressure cap? |
|
|
The idea of maintaining an 'air gap' in the pressurized system is nonsense. Spreading that concept is a disservice. If everything is working correctly it is not possible to maintain an air gap without continuously introducing air into the system. The system purges air out of the pressure tank each time it heats up fully. That air flows to the burp tank where it floats out. When the engine cools and the system goes to vacuum, only coolant can be pulled back into the system because the connection to the burp tank is at the bottom of the tank. Other vehicles that have an air gap in their pressure tank do not ever have a burp tank setup like the Vanagon and instead just burp coolant to the ground if the pressure tank is overfull. With the Vanagon setup, if there is an air gap in the pressure tank after a few heat cycles, that indicates that there is a leak in the cooling system that is introducing air (or combustion gases) into the coolant. |
|
Back to top |
|
|
alaskadan Samba Member
Joined: January 09, 2013 Posts: 1857 Location: anchor pt. alaska
|
Posted: Mon Oct 04, 2021 9:12 am Post subject: Re: Is this a sign of a bad coolant pressure cap? |
|
|
I'd check the upper nipple of your new pressure tank to make sure it's clear. I've seen two tanks in my years where they weren't drilled through and was a pita to figure out. |
|
Back to top |
|
|
AtlasShrugged Samba Member
Joined: October 30, 2008 Posts: 1605 Location: Decatur, Ga. USA
|
Posted: Mon Oct 04, 2021 9:27 am Post subject: Re: Is this a sign of a bad coolant pressure cap? |
|
|
I'm not here to quarrel but think about it. Looking at most VW/Audi/Porsche cars that have a pressurized coolant tank-all of them have a MIN and MAX mark and an air cushion or gap at the top. A Google search will show what I'm talking about. My Vanagon coolant tank cracking, caps failing and hoses leaking problems stopped many, many years ago when I stopped filling the pressure tank all the way to the brim but rather filled it to just above the MIN mark on the tank (cold). Even that fancy GoWesty metal tank has a sight glass on the side for "accurate coolant level readings" . If that metal tank is needs to be filled all the way to the brim, the sight glass would be built in at the top.
That extra tank behind the license plate is part of a "coolant recovery system" and not the true indicator of the "coolant level" in the Vanagon. The coolant capacity of the recovery tank is very small. It is a recovery reservoir and works fine with an air gap in the pressurized coolant tank.
Try running an air gap in the top of your coolant tank long term and save yourself a lot of expensive coolant system problems.
_________________ 'Let's Go Brandon' |
|
Back to top |
|
|
?Waldo? Samba Member
Joined: February 22, 2006 Posts: 9752 Location: Where?
|
Posted: Mon Oct 04, 2021 9:47 am Post subject: Re: Is this a sign of a bad coolant pressure cap? |
|
|
As I mentioned in my prior post, NONE of the vehicles that have a max/min on the pressure tank have a burp tank setup like the vanagon. If overfull, they just puke coolant onto the ground when the coolant expands and draw air back in from atmosphere when the system cools.
It is **not possible** to run an air gap in the vanagon system unless you keep introducing air into the pressure tank through a leak or through intention. Any air in the pressure tank will just get burped back out in a heat cycle or two and within a few heat cycles you will be back to a completely full pressure tank **unless there is a leak in the system**. If you have been consistently running an 'air gap' with a stock Vanagon cooling system then you have a leak in your system that is introducing air. |
|
Back to top |
|
|
|