Hello! Log in or Register   |  Help  |  Donate  |  Buy Shirts  See all banner ads | Advertise on TheSamba.com  
TheSamba.com
 
Classifieds Index -> Parts -> High Performance/Engine
Correct Geometry 1.1 or 1.25 Rocker Arms Turn on always show all large photos     Ad id: 1925154
Photo
Additional Photos
Click to load image
L & R arrow keys scroll through photos
Photo Photo Photo
Photo Photo
CB 1.25s
Photo
CB 1.25s
Photo
Genuine 911 Adjusterd
Photo
Thorsten Pieper Tool Steel
Photo
Left-STD vs. Right-3MM narrowed
Correct Geometry 1.1 or 1.25 Rocker Arms   Price: 70
Original used VW rockers have been modified to work with CB, EMPI, Porsche, and Thorsten Pieper swivel adjusters/Elephant's Feet. They've been cut down and dished with carbide endmills. This is the most professional-looking machining to correct rocker geometry available. These are difficult to modify in this fashion, and require fairly expensive cutting tools. The thrust surfaces are sanded smooth with 320-grit, then 600-grit on a (+/-) .001" surface table to make setting up side play easier. The surfaces become almost polished for reduced wear, heat, and friction. On average, these allow you to screw your adjusters back another .120". All 1.1:1 rockers need to be cut back for proper geometry. A shortcut is to shim the rockers all the way out. This requires the pushrods to be longer, and the max lift usually suffers. The price of the set depends on the price of the cores, which vary depending who I buy from. Just message me, and I'll get you a current price. They typically range from $80-$90. With EMPI HD shafts, swivels and a couple shim kits, you'll come out about the same price as a SCAT 1.1 set, and they'll work correctly. Also, if you send me your 1.1 or 1.25 rockers (bare disassembled and somewhat clean) the work alone will only cost $70. Machined CB rockers (1.1s or 1.25s) are $160 to your door, if you live in the U.S. They're highly recommended, as all used O.E.M. rockers have wear at some level.

I can also supply HD shafts (CB, SCAT, EMPI, Berg), shims, and various brands of adjusters (Porsche-$192, CB-$40, Thorsten Pieper tool steel-$110) to make a complete kit. I can supply surfaced rocker blocks for $15 extra, and can narrow them 3MM for more accurate valve-to-adjuster alignment for $40 (machine work only).

_________________
My Paypal is the same as my email: [email protected]

Please add 2.5% of the total for Paypal transactions or send as a gift to waive fees.

I ship via USPS (Flat Rate if possible). I try to send next or same day, but sometimes due to my schedule, it may take longer. If that's the case, I'll make sure to communicate that to you.
Advertiser information Ad information
Advertiser:
Name:
Member since:
bugguy1967
Tabari
January 16, 2008
Contact advertiser

Phone: Click to Show

Email this Advertiser
Email this Advertiser
Location: 
Ad placed: 
Ad renewed: 
Ad last edited: 
Views: 
Category: 
Payments accepted: 
Los Angeles, California, USA Map it
Thu May 05, 2016 7:45 pm
Wed Sep 11, 2019 8:02 am
Sat Aug 10, 2019 12:44 pm
3957
Parts - High Performance/Engine
Cash
Paypal
Money order/Bank check
Personal check

View other ads View profile Search for Feedback Watch this ad | Report this Ad
Watch this seller Share: Email Facebook Twitter
Other ads from bugguy1967
See all | See ads in this category
N.O.S. Watercooled Oil Pressure Switches
N.O.S. Watercooled Oil Pressure Switches
Late Bus Stainless Rear Wheel Cotter Pins
Late Bus Stainless Rear Wheel Cotter Pins
Stainless Weber IDF Hairpins For Accel Pump Rod
Stainless Weber IDF Hairpins For Accel Pump Rod
Dellorto DRLA Float Securing E-Clips
Dellorto DRLA Float Securing E-Clips
68 - 71 T2 Bus Clutch Cable
68 - 71 T2 Bus Clutch Cable


About | Help | Advertise | Donate | Premium Membership | Privacy/Terms of Use | Contact Us | Site Map
Copyright © 1996-2018, Everett Barnes. All Rights Reserved.
Not affiliated with or sponsored by Volkswagen of America | Forum powered by phpBB