Search found 75 matches

EVfun · Posted: Sun Jan 06, 2019 12:30 pm Size: 1200x900 Views: 13 Rating: Not rated

EVfun
A few shots of it in the driveway while I cleaned up the garage floor.

EVfun · Posted: Sun Jan 06, 2019 12:30 pm Size: 1200x900 Views: 12 Rating: Not rated

EVfun
A few shots of it in the driveway while I cleaned up the garage floor.

EVfun · Posted: Sun Jan 06, 2019 12:30 pm Size: 1200x900 Views: 12 Rating: Not rated

EVfun
A few shots of it in the driveway while I cleaned up the garage floor.

EVfun · Posted: Sat Jan 05, 2019 2:18 pm Size: 1200x900 Views: 19 Rating: Not rated

EVfun
14 inch Bus wheels with almond powdercoat
Front are stock with P175/65R14 tires
Rear widened to 8 inches with P225/70R14 tires

EVfun · Posted: Sun Nov 11, 2018 8:06 pm Size: 1333x1000 Views: 18 Rating: Not rated

EVfun
1 year only madness, in 1960 VW decided to move the axles down 15mm to reduce rear camber. They did so by reshaping the rear frame forks to move the transaxle down and moving the front of the transaxle down even more to mount the drivetrain at a 2 degree front down angle. The front change required a new nosecone with the hockey stick moved up. By doing it this way the rear of the engine ended up at the same height as before. The following year they changed the transaxle and front mount.

EVfun · Posted: Sun Nov 11, 2018 8:06 pm Size: 1000x1500 Views: 11 Rating: Not rated

EVfun
1 year only madness, in 1960 VW decided to move the axles down 15mm to reduce rear camber. They did so by reshaping the rear frame forks to move the transaxle down and moving the front of the transaxle down even more to mount the drivetrain at a 2 degree front down angle. The front change required a new nosecone with the hockey stick moved up. By doing it this way the rear of the engine ended up at the same height as before. The following year they changed the transaxle and front mount.

EVfun · Posted: Fri Sep 14, 2018 3:10 pm Size: 600x800 Views: 26 Rating: Not rated

EVfun
This is the left side, the right side is slightly better but not close enough to start all the bolts and nuts.

EVfun · Posted: Sun Jul 08, 2018 7:24 pm Size: 1200x900 Views: 50 Rating: Not rated

EVfun
Hydraulic clutch installation, and a bit of the T-bucket gas tank too.

EVfun · Posted: Sun Jul 08, 2018 7:24 pm Size: 1200x900 Views: 20 Rating: Not rated

EVfun
Hydraulic clutch installation, and a bit of the T-bucket gas tank too.

EVfun · Posted: Sun Jul 08, 2018 7:24 pm Size: 1200x900 Views: 9 Rating: Not rated

EVfun
Hydraulic clutch installation, and a bit of the T-bucket gas tank too.

EVfun · Posted: Sun Jul 08, 2018 7:19 pm Size: 800x600 Views: 27 Rating: Not rated

EVfun
The white one is boring.

EVfun · Posted: Thu Jul 05, 2018 11:40 am Size: 1200x900 Views: 13 Rating: Not rated

EVfun
If you look at the dimension of the groove for the retaining clip you will see it is 13mm. It should be 12mm to fit the brake line retaining clip.

EVfun · Posted: Sun Jul 01, 2018 12:09 pm Size: 1600x1200 Views: 17 Rating: Not rated

EVfun
1950 Pontiac tail lights in my Berry Mini-T

EVfun · Posted: Sun Jul 01, 2018 11:56 am Size: 1200x900 Views: 25 Rating: Not rated

EVfun
My Berry Mini-t in the garage for the winter, taken the fall of 2013 (red convertible) and fall of 2017 (black oval.)

EVfun · Posted: Sun Jul 01, 2018 11:56 am Size: 1200x900 Views: 19 Rating: Not rated

EVfun
My Berry Mini-t in the garage for the winter, taken the fall of 2013 (red convertible) and fall of 2017 (black oval.)

EVfun · Posted: Fri Jun 22, 2018 2:57 pm Size: 1200x900 Views: 15 Rating: Not rated

EVfun
Reproduction '73 Thing exhaust with a black ceramic coating.

EVfun · Posted: Sun Apr 01, 2018 5:42 pm Size: 800x600 Views: 29 Rating: Not rated

EVfun
I have a new gauge to shove in the dash. I want to thank Speedhut for being able to give tell me the custom choices I made several years ago for my speedo years ago so I could buy a matching fuel gauge.

EVfun · Posted: Sun Apr 01, 2018 5:42 pm Size: 800x600 Views: 10 Rating: Not rated

EVfun
I have a new gauge to shove in the dash. I want to thank Speedhut for being able to give tell me the custom choices I made several years ago for my speedo years ago so I could buy a matching fuel gauge.

EVfun · Posted: Sun Apr 01, 2018 8:31 am Size: 1000x750 Views: 22 Rating: Not rated

EVfun
I cut and bent the shifter back near base.

EVfun · Posted: Sun Apr 01, 2018 8:29 am Size: 600x800 Views: 17 Rating: Not rated

EVfun
I found these on a '64 Bug I looked at.

EVfun · Posted: Sun Mar 25, 2018 8:21 pm Size: 1000x750 Views: 21 Rating: Not rated

EVfun
A Speedway Motors T-bucket gas tank is in place on the old battery rack.

EVfun · Posted: Sat Mar 24, 2018 12:01 pm Size: 1000x750 Views: 9 Rating: Not rated

EVfun
More pictures of the rebuild of my Berry Mini-T. I think that will make a nice faux radiator cap.

EVfun · Posted: Sat Mar 24, 2018 12:01 pm Size: 1000x750 Views: 14 Rating: Not rated

EVfun
One stud on the rear mount broke. Both where chewed up. The originals where ground off, center punched, and drilled out. New cap screws replace them.

EVfun · Posted: Sun Jan 07, 2018 12:36 pm Size: 750x1000 Views: 32 Rating: Not rated

EVfun
Photos documenting the rebuild of my Berry Mini-T.

This looks like a fine place for a T-bucket gas tank.

EVfun · Posted: Sun Jan 07, 2018 12:36 pm Size: 1000x750 Views: 41 Rating: Not rated

EVfun
Photos documenting the rebuild of my Berry Mini-T

EVfun · Posted: Sun Jan 07, 2018 12:36 pm Size: 1000x750 Views: 44 Rating: Not rated

EVfun
Photos documenting the rebuild of my Berry Mini-T.

It starts by quickly pulling the body.

EVfun · Posted: Fri Dec 15, 2017 6:26 pm Size: 900x1200 Views: 24 Rating: Not rated

EVfun
I am considering mounting these small lights next to the headlights are cowl lights where the windshield meets the body. They have an amber bulb and could function as turn signals and parking lights.

EVfun · Posted: Sat Dec 09, 2017 1:09 pm Size: 1200x800 Views: 31 Rating: Not rated

EVfun
A preview of how the wide smoothies with P225/70R14 tires will look on the back of my Berry Mini-T.

EVfun · Posted: Sun Nov 26, 2017 8:02 pm Size: 1200x900 Views: 31 Rating: Not rated

EVfun
The front are 14x5 stock Bus wheels and the rear are 14x8 widened Bus wheels with a nice deep dish, the ET is -20mm

EVfun · Posted: Sat Nov 25, 2017 9:46 am Size: 1200x900 Views: 43 Rating: Not rated

EVfun
This is a shot of the car out and about with shiny new slotted mags.

EVfun · Posted: Sat Nov 25, 2017 9:44 am Size: 1200x900 Views: 43 Rating: Not rated

EVfun
A shot of the '57 Bug and '64 pan Mini-T tucked away safely.

EVfun · Posted: Tue Nov 14, 2017 10:18 pm Size: 1200x900 Views: 27 Rating: Not rated

EVfun
A made a new, longer bracket for the reserve handle I included a pushbutton switch to add a "mist mode" to the 6 volt wipers.

EVfun · Posted: Mon Aug 07, 2017 10:25 pm Size: 480x640 Views: 21 Rating: Not rated

EVfun

EVfun · Posted: Fri Jul 14, 2017 7:07 pm Size: 1000x800 Views: 33 Rating: Not rated

EVfun
Here are a couple shots of how I used a standard buggy windshield frame mount to attach the center rear view mirror on an Mini-T windshield with a slightly different extrusion profile.

EVfun · Posted: Fri Jul 14, 2017 7:07 pm Size: 750x1000 Views: 28 Rating: Not rated

EVfun
Here are a couple shots of how I used a standard buggy windshield frame mount to attach the center rear view mirror on an Mini-T windshield with a slightly different extrusion profile.

EVfun · Posted: Fri Dec 23, 2016 10:12 pm Size: 1024x768 Views: 108 Rating: Not rated

EVfun
A mechanical brake light switch to eliminate the sometimes troublesome pressure switches in the master cylinder.

EVfun · Posted: Wed Aug 31, 2016 7:18 pm Size: 640x480 Views: 14 Rating: Not rated

EVfun
I show 2 different designs of headlamp bulb retaining clips for '66 and earlier headlight assemblies.

EVfun · Posted: Tue Aug 09, 2016 2:41 pm Size: 640x480 Views: 23 Rating: Not rated

EVfun
I believe this SG key was cut incorrectly.

EVfun · Posted: Sat Jun 11, 2016 1:04 pm Size: 1000x750 Views: 48 Rating: Not rated

EVfun
Marable Motors license plate frame mounted with a reproduction 1955 Chevy Bel Air license plate frame.

EVfun · Posted: Sat Jun 11, 2016 12:48 pm Size: 750x1000 Views: 113 Rating: Not rated

EVfun
Marable Motors license plate frame mounted with a reproduction 1955 Chevy Bel Air license plate frame.

EVfun · Posted: Sun Mar 06, 2016 10:59 am Size: 800x600 Views: 41 Rating: Not rated

EVfun

EVfun · Posted: Sat Feb 20, 2016 9:13 pm Size: 1000x750 Views: 42 Rating: Not rated

EVfun

EVfun · Posted: Sat Feb 20, 2016 9:13 pm Size: 750x1000 Views: 78 Rating: Not rated

EVfun

EVfun · Posted: Sun Jan 17, 2016 5:29 pm Size: 800x600 Views: 81 Rating: Not rated

EVfun
I modified an inexpensive reserve handle extension so it would work better.

EVfun · Posted: Sun Jan 17, 2016 5:29 pm Size: 800x600 Views: 60 Rating: Not rated

EVfun
I modified an inexpensive reserve handle extension so it would work better.

EVfun · Posted: Sun Jan 17, 2016 5:29 pm Size: 794x600 Views: 63 Rating: Not rated

EVfun
I modified an inexpensive reserve handle extension so it would work better.

EVfun · Posted: Sat Dec 12, 2015 8:42 pm Size: 600x800 Views: 57 Rating: Not rated

EVfun

EVfun · Posted: Sat Dec 12, 2015 12:34 pm Size: 1280x960 Views: 64 Rating: Not rated

EVfun

EVfun · Posted: Sat Dec 05, 2015 1:46 pm Size: 640x480 Views: 47 Rating: Not rated

EVfun
A set of these where on a Bug I bought. I have never seen early style hubcaps with a raised logo before. They also lack holes for a hub cap puller.

EVfun · Posted: Sat Dec 05, 2015 1:46 pm Size: 360x480 Views: 25 Rating: Not rated

EVfun
A set of these where on a Bug I bought. I have never seen early style hubcaps with a raised logo before. They also lack holes for a hub cap puller.


Hello! Log in or Register \| Help \| Donate \| Buy Shirts	See all banner ads \| Advertise on TheSamba.com