| ALLWAGONS |
Sun Jan 07, 2024 1:38 pm |
|
| Do only type 34's have the inner tire support bracket on the spare tire bowl? or do other models have it too? My '65 squareback does not have it. My type 34 does. |
|
| Bobnotch |
Sun Jan 07, 2024 2:13 pm |
|
| I think so. I've never seen one on either a Square or a Notch, but my T-34 did have one. |
|
| ALLWAGONS |
Thu Feb 20, 2025 7:15 pm |
|
Anyone know when type 34 tail light bases got the rubber cap to protect the wiring on the light bulb. See top and bottom. My parts manual is dated 1972 and it only shows the base with the rubber cap.
|
|
| squaretobehip |
Fri Feb 21, 2025 1:17 pm |
|
ALLWAGONS wrote: Anyone know when type 34 tail light bases got the rubber cap to protect the wiring on the light bulb. See top and bottom. My parts manual is dated 1972 and it only shows the base with the rubber cap.
I checked my parts books.
1961 - No cap
1963 - No cap
1969 - Cap
There's also no chassis breakdown for the tail light or cap. A T34 super nerd is gonna have to chime in here. |
|
| notchboy |
Fri Feb 21, 2025 6:33 pm |
|
| I was going to say the no cap is an early thing but have no idea about cut off date. I was happy to have early, cast, two piece rear lights that have caps. That way you can detach the chrome ring and put the restored ring onto a cast body, capped tail light. |
|
| notchboy |
Fri Feb 21, 2025 6:35 pm |
|
All of which I didnt figure out till it was all in front of my face. Im lucky to have good- OG ruber caps as well.
|
|
| Splitdog |
Sun Nov 23, 2025 8:10 pm |
|
Does anyone have, or make the electrical piece of the front turn signal housing?
I want to convert mine to dual filament. Any ideas would be appreciated. |
|
| bullethead |
Mon Dec 01, 2025 2:01 pm |
|
Windshield Trim?
Having a time trying to polish the windshield brightwork, front and rear. Is anyone reproducing these pieces or have success re-anodizing them?
Thanks! |
|
| Splitdog |
Mon Dec 01, 2025 2:08 pm |
|
| Isn't that stainless steel? Just polish it and it should be good to go for a long time. |
|
| bullethead |
Mon Dec 01, 2025 4:50 pm |
|
| No, hard anodized aluminum. If it was stainless it would take a polish easily. 4-0 Stainless wool isn't removing the discoloration which is baffling... I'll post a couple of pics showing the problem. |
|
| ibjack |
Mon Dec 01, 2025 8:08 pm |
|
| ISP sold a repop set a while back. |
|
| notchboy |
Tue Dec 02, 2025 8:29 pm |
|
Splitdog wrote: Does anyone have, or make the electrical piece of the front turn signal housing?
I want to convert mine to dual filament. Any ideas would be appreciated.
I made mine dual with these
https://www.snydersantiqueauto.com/product.htm?pid=976595&cat=41888
Slipped in the og hole with some aluminum tape. |
|
| Splitdog |
Tue Dec 02, 2025 9:25 pm |
|
| Nice. I just ordered. What's the deal with the $1.00 then wait? |
|
Powered by phpBB © 2001, 2005 phpBB Group
|