thomas. |
Thu Jan 28, 2016 6:35 am |
|
Sharp64 wrote: That's just a handle to a pretty common scissor style if im not mistaken.
From the classifieds a repop;
http://www.thesamba.com/vw/classifieds/detail.php?id=1090316 |
|
EMPIImp69 |
Thu Jan 28, 2016 7:39 am |
|
Sharp64 wrote: That's just a handle to a pretty common scissor style if im not mistaken.
I think your right, it almost looks too thin to be a crank handle. It's the same thickness as the correct lug/jack handle I need. |
|
EMPIImp69 |
Tue Feb 09, 2016 6:50 pm |
|
Polished out the slide rails for the rag assembly. Been renovating a bathroom in the house so not much done on the bug.
|
|
EMPIImp69 |
Thu Feb 25, 2016 6:28 pm |
|
Got my beam narrowed 3.5" and wheels widened to 15x8s and 15x6s. Decided to go with wide steelies instead of the polished 5 spokes. Not sure yet what color I'll paint them yet.
|
|
EMPIImp69 |
Wed Mar 09, 2016 5:36 pm |
|
Built a body dolly. Made it tall enough so frame can roll under it. Body coming back off soon
|
|
EMPIImp69 |
Sun Mar 13, 2016 6:12 pm |
|
Got the shell on the dolly. Started stripping the rear apron of paint. Going to be a long road ahead of paint stripping, sanding and new paint prep.
|
|
EMPIImp69 |
Tue Mar 22, 2016 6:53 pm |
|
Had this rear apron latch cut out of another car and welded it onto the aftermarket rear apron I have. Still need to grind the welds and line up the decklid better.
Also got some new tires for the rear 8" smoothies 225/50/15 and some more parts off CL including a Scat 35 cam for the engine. Wires are old school.
|
|
EMPIImp69 |
Tue May 10, 2016 6:01 pm |
|
Been working on the bug again. Got some shock towers, welded them to the beam and shortened the leaves. Painted the beam again, painted the frame head, steering box and bolted the beam back on.
|
|
EMPIImp69 |
Tue May 10, 2016 6:07 pm |
|
I picked up some 1.25" wider fiberglass rear fenders but I'm not sure if I'm going to use them yet.
I also am converting this later model fender to early style in case I go with stock size steel fenders
Other side
|
|
EMPIImp69 |
Tue May 10, 2016 6:11 pm |
|
Also put in new cable boots. Still need to replace clutch crossshaft and bushings.
|
|
EMPIImp69 |
Tue May 10, 2016 6:34 pm |
|
Here's what I did on the beam after I cut down the stock shock towers.
Had to mark and dimple the leaves
|
|
EMPIImp69 |
Tue May 17, 2016 5:43 am |
|
Pulled it outside, started sanding down some of the surface rust. Still more to go.
Pulled the harness out
I ended up using a later model fender on the pass side, so I filled in the bumper bracket area
Primed the fenders & cut the opening for the bumper bracket. Still need to drill for the overrider hole.
|
|
grandpa pete |
Tue May 17, 2016 7:21 am |
|
Why is there a hose clamp on your Bowden tube ?? |
|
EMPIImp69 |
Tue May 17, 2016 4:03 pm |
|
grandpa pete wrote: Why is there a hose clamp on your Bowden tube ??
Its keeping the dust boot from moving. |
|
EMPIImp69 |
Tue May 17, 2016 6:43 pm |
|
Cleaned up the tie rods and shortened them about an inch and tapped the ends. May need to shorten them a little more. Going to change driver side tie rod ends.
|
|
EMPIImp69 |
Sun May 22, 2016 5:48 pm |
|
Pretty much wrapped up the front end and put in the pedal assembly.
Put in new cross shaft and bushings
Finished drilling the hole for over rider in this fender.
Did some more sanding and bodywork.
Used Evercoat Rage on the quarter panel. Stuff is nice and smooth, goes on like butter and sands well too.
|
|
EMPIImp69 |
Sat May 28, 2016 5:57 pm |
|
Got the tires mounted on the polished 5 spokes I got. Pretty much level front and rear.
|
|
grandpa pete |
Sat May 28, 2016 6:06 pm |
|
Coming along ; I like the silver gray chassis :) |
|
EMPIImp69 |
Sat May 28, 2016 6:12 pm |
|
grandpa pete wrote: Coming along ; I like the silver gray chassis :)
Thanks Grandpa, that's just Rustoleum hammered silver. |
|
EMPIImp69 |
Tue Jun 07, 2016 5:29 pm |
|
Picked up a NOS driver door. Will be using this one since its better than the other 2 driver side ones I have.
Started sanding it down, its in like perfect shape.
|
|
Powered by phpBB © 2001, 2005 phpBB Group
|