Hello! Log in or Register
| Help | Donate | Buy Shirts ![]() |
See all banner ads | Advertise on TheSamba.com |
![]() |
|
|
Search found 158 matches |
Page: 1, 2, 3, 4, 5, 6, 7, 8 Next |
Author | Message |
---|---|
![]() |
|
Mr Brown Replies: 10 Views: 284 |
![]() |
I use Ravenol TSG 75W90 semi synthetic. I tried many different types, VW G50, the new VW stuff, mineral GL4, GL5, Amsoil, Redline etc and the TSG works best for our climate here, super hot summers an ... | |
![]() |
|
Mr Brown Replies: 7 Views: 372 |
![]() |
Sure it is the gearbox leaking? I rebuilt my gearbox( some time ago so a little fuzzy) and while I didn't change the seal in the van it should be pretty straight forward. The image shown in the previ ... | |
![]() |
|
Mr Brown Replies: 12 Views: 484 |
![]() |
I bought new film from an Ebay seller in the UK, pretty close cut but needed some trimming. I took the middle window out to do it. Indistinguishable from the original. 4 years and still looks good. H ... | |
![]() |
|
Mr Brown Replies: 3 Views: 2065 |
![]() |
I just run 43 front and back. | |
![]() |
|
Mr Brown Replies: 11 Views: 1090 |
![]() |
I have the C-Line Van tires 205 65 15 on my 94 EV GLS and they are excellent so far; three summers. Super quiet, nice ride, wear is decent so far, excellent in the rain. I don't do much high speed dr ... | |
![]() |
|
Mr Brown Replies: 2 Views: 405 |
![]() |
That coolant fitting with the two hoses should have an o-ring on it. | |
![]() |
|
Mr Brown Replies: 30 Views: 1856 |
![]() |
I rebuilt my gearbox last summer, not too difficult but then I had an aircraft component overhaul shop at my disposal. Those rollers are most likely from the small bearing in the mainshaft which is t ... | |
![]() |
|
Mr Brown Replies: 14 Views: 930 |
![]() |
Replacing the injectors requires removing the intake manifold. Right? How big a job is that?
Not on the AAF engine anyway. I did the injector seals last year and it wasn't too bad to get at. Harde ... |
|
![]() |
|
Mr Brown Replies: 1 Views: 304 |
![]() |
Window is bolted in I believe, have to take the interior trim off. | |
![]() |
|
Mr Brown Replies: 30 Views: 1377 |
![]() |
How did the Transmission ECM get water on it? It is inside the van. More likely water in a connection to the transmission itself. Do you have the sound deadening pan installed?
The same fellow I ... |
|
![]() |
|
Mr Brown Replies: 30 Views: 1377 |
![]() |
I believe this van still has the trans in it: http://www.thesamba.com/vw/classifieds/detail.php?id=1820985 | |
![]() |
|
Mr Brown Replies: 16 Views: 957 |
![]() |
I have also had a Sanden compressor failure just now, leaking shaft seal which contaminated the clutch. Lasted only 9 months, going to have another installed under warranty and see what happens. | |
![]() |
|
Mr Brown Replies: 13 Views: 1810 |
![]() |
You don't need to remove the dash to change the fan, or do any cutting. Just loosen the dash side bolts, bolt in engine compartment, remove lower center dash panels and glovebox, remove cruise contro ... | |
![]() |
|
Mr Brown Replies: 30 Views: 14168 |
![]() |
I am using Castrol Edge 5W50 year round in my 94 right now. Can get it on sale regularly at Canadian Tire for $35. No oil consumption at all.
Used Shell Rotella mineral for a while which worked ve ... |
|
![]() |
|
Mr Brown Replies: 11 Views: 1259 |
![]() |
From experience its always the combustion blower or safety switch. If the capacitors are cooked for the combustion blower points replace them, I went to an electronics supply store and they had some ... | |
![]() |
|
Mr Brown Replies: 21 Views: 3637 |
![]() |
Thumbs up for 3M 1357. We use it on aircraft interiors and I used it on my westy interior vinyl; after I used 5 different kinds of spray adhesive which all failed in the heat. Don`t use anything else ... | |
![]() |
|
Mr Brown Replies: 13 Views: 1210 |
![]() |
I had this when all the shim washers on the distributor shaft departed. The rotor rubbed the cap as it pushed too far up due to all the play in the distributor shaft. | |
![]() |
|
Mr Brown Replies: 6 Views: 510 |
![]() |
Just adjust it until your happy with it. Loosen that little nut on the back and move the stud up or down, very sensitive. Be gentle on the nut as it strips easily. | |
![]() |
|
Mr Brown Replies: 2 Views: 374 |
![]() |
I haven't seen one. Look for a used hard copy, I just bought the one that was posted in the classifieds. Amazon has them on sale right now as well. | |
![]() |
|
Mr Brown Replies: 19 Views: 1970 |
![]() |
Just take down to AATransaxle. I did this a few years ago, nice drive and no hassle/duties at the border. Can't go wrong there, my first rebuild I had done locally failed within a year and it cost m ... | |
Page: 1, 2, 3, 4, 5, 6, 7, 8 Next All times are Mountain Standard Time/Pacific Daylight Savings Time |