Hello! Log in or Register
| Help | Donate | Buy Shirts ![]() |
See all banner ads | Advertise on TheSamba.com |
![]() |
|
|
Search found 1189 matches |
Page: 1, 2, 3 ... 58, 59, 60 Next |
Author | Message |
---|---|
![]() |
|
hobbybob517 Replies: 211 Views: 10890 |
![]() |
That looks crazy expensive ![]() https://www.thesamba.com/vw/gallery/pix/2009870.jpg https://www.thesamba.com/vw/gallery/pix/2009871.jpg this is a 177 ... |
|
![]() |
|
hobbybob517 Replies: 211 Views: 10890 |
![]() |
That looks crazy expensive ![]() this one is not so bad , i use Kaiser cutting head upwards of 13K € the finish is ultimate, tolerance within 0.005 mm |
|
![]() |
|
hobbybob517 Replies: 211 Views: 10890 |
![]() |
[youtube]https://youtu.be/SP8l54lAtZY[/youtube] | |
![]() |
|
hobbybob517 Replies: 211 Views: 10890 |
![]() |
Boring out holes is easy, no problem. What is hard is facing a surface flat at the bottom of the hole.
THe automatic facing head expands say, .004" each revolution, so it's only cutting .0 ... |
|
![]() |
|
hobbybob517 Replies: 377 Views: 39088 |
![]() |
Post a video! | |
![]() |
|
hobbybob517 Replies: 12 Views: 648 |
![]() |
The 1300 F has tiny oil passages, and a tiny oil pick up tube,
i would at least go and look for a AB case |
|
![]() |
|
hobbybob517 Replies: 377 Views: 39088 |
![]() |
Getting there! | |
![]() |
|
hobbybob517 Replies: 26 Views: 1504 |
![]() |
I wouldnt use them at all, unlesss this 2275 is low DCR. (A lot of cam duration like FK10 or 87) They are too warm. Dependant on DCR and use of the car/engine you need at least 1 number colder, maybe ... | |
![]() |
|
hobbybob517 Replies: 7 Views: 422 |
![]() |
what ignition are you running?
Horrible - an .009 centrifugal with Pertronix points, blue coil, NGK long reach as I have big valve heads on it. I am seriously considering going to a CB Magnaspark ... |
|
![]() |
|
hobbybob517 Replies: 7 Views: 422 |
![]() |
what ignition are you running? | |
![]() |
|
hobbybob517 Replies: 26 Views: 855 |
![]() |
if you open it up, it's line bore time ( 9/10 times ) | |
![]() |
|
hobbybob517 Replies: 40 Views: 2940 |
![]() |
Had a set of kolbenschmidt main bearings and the split bearing 1 half was warped, ttok me an afternoon to figure it out, now i only use silver line steel backs | |
![]() |
|
hobbybob517 Replies: 14 Views: 859 |
![]() |
Don't use the paper gaskets under the cylinders,
also do not apply anything on the oil pump gaskets. |
|
![]() |
|
hobbybob517 Replies: 11 Views: 825 |
![]() |
Looks like a nice little hobby lathe,
i personaly like them a bit bigger, once you go VDF you can't go back ![]() |
|
![]() |
|
hobbybob517 Replies: 3 Views: 176 |
![]() |
maybe the trottle closes to fast creating a big vaccuum , did you add return springs? | |
![]() |
|
hobbybob517 Replies: 35 Views: 3969 |
![]() |
I have the CSP, a very nice product!
https://www.thesamba.com/vw/gallery/pix/1915640.jpg https://www.thesamba.com/vw/gallery/pix/1934577.jpg https://www.thesamba.com/vw/gallery/pix/1934576.jp ... |
|
![]() |
|
hobbybob517 Replies: 59 Views: 1976 |
![]() |
It came back today | |
![]() |
|
hobbybob517 Replies: 16 Views: 457 |
![]() |
Isn't the 34 pict-3 supossed to be combined with a SVDA dist? | |
![]() |
|
hobbybob517 Replies: 23 Views: 963 |
![]() |
you could have it like a shift light, no way you would miss that. | |
![]() |
|
hobbybob517 Replies: 59 Views: 1976 |
![]() |
Update;
Today was a very hot day, i drove for about 20 miles, and after about 10 miles i was waiting at a red light and the noise went away. will check again tomorrow when the engine is cold. |
|
Page: 1, 2, 3 ... 58, 59, 60 Next All times are Mountain Standard Time/Pacific Daylight Savings Time |