| Author |
Message |
EverettB 
Administrator
Joined: April 11, 2000
Posts: 70834
Location: Phoenix 602
|
|
| Back to top |
|
 |
B_vdd
Samba Member
Joined: March 18, 2021
Posts: 4
Location: Belgium
|
 Posted: Sun Oct 13, 2024 12:54 am Post subject: Re: 1954 & 1955 engines whats not correct! |
 |
|
| EverettB wrote: |
Are you asking if the cylinder tin should be 3-hole?
Yes.
|
Yes those with the different pressing. |
|
| Back to top |
|
|
bnam
Samba Member
Joined: July 02, 2006
Posts: 3368
Location: El Dorado Hills CA/ Bangalore, India
|
| Posted: Tue Oct 22, 2024 8:38 am Post subject: Re: 1954 & 1955 engines whats not correct! |
|
|
| RockStock wrote: |
| sgellis wrote: |
| Was the fastener on end of fan shroud a flat head or hex head? |
Should be a cheese head screw, not the hex head. |
The parts manual says different - N 10 212 3, bolt, hex head 6x12.
Byas
_________________
1971 1302LS Convertible (RHD) owned since '74
Click to view image
1965 Karmann Ghia Coupe - under restoration
1966 Fiat 1500 Cabrio (with 1600 Twin cam)
1952 Citroen TA 11BL |
|
| Back to top |
|
|
RockStock
Samba Member
Joined: November 26, 2004
Posts: 4088
Location: England
|
| Posted: Tue Oct 22, 2024 1:20 pm Post subject: Re: 1954 & 1955 engines whats not correct! |
|
|
One example. Jan 55 bus engine.
1954 Bus Parts Manual
#45
_________________
-StockRocks- |
|
| Back to top |
|
|
bnam
Samba Member
Joined: July 02, 2006
Posts: 3368
Location: El Dorado Hills CA/ Bangalore, India
|
| Posted: Tue Oct 22, 2024 8:59 pm Post subject: Re: 1954 & 1955 engines whats not correct! |
|
|
You’re right it seems to have been superseded only sometime after 67 with 2 hex bolts.
The fan cover screws seem to have been hex bolts throughout.
_________________
1971 1302LS Convertible (RHD) owned since '74
Click to view image
1965 Karmann Ghia Coupe - under restoration
1966 Fiat 1500 Cabrio (with 1600 Twin cam)
1952 Citroen TA 11BL |
|
| Back to top |
|
|
janerick3
Samba Member
Joined: June 04, 2006
Posts: 1892
Location: Colorado
|
| Posted: Wed Oct 23, 2024 3:28 am Post subject: Re: 1954 & 1955 engines whats not correct! |
|
|
I think the confusion comes from the 356 community, where the purists are much more anal.
356/912 fan shrouds, which are no more than modified VW stampings, are held in place by 2 hex bolts on the ends. I have never seen an original 36 or 40hp VW engine with anything other than cheese head screws holding the fan shroud in place.
_________________
Thanks,
Jan K. |
|
| Back to top |
|
|
1957_SC
Samba Member
Joined: June 30, 2008
Posts: 24
Location: Pomona, CA
|
| Posted: Mon Nov 11, 2024 7:28 pm Post subject: Re: 1954 & 1955 engines whats not correct! |
|
|
Anyone know if there is anything unique to the Heater box tin, no the box itself, but rather the "Sled" that runs under the pushrod tubes with the flap?
Looking for one for an early 55 (jan) engine, and not sure if I am looking for something specifc.
Thanks |
|
| Back to top |
|
|
|
