Author |
Message |
kintail Samba Member
Joined: January 01, 2003 Posts: 659 Location: Canada
|
Posted: Sat Dec 07, 2024 9:40 pm Post subject: Re: New project - 1954 VW Beetle Deluxe w/ VW Canada prodn plate |
|
|
Pulled the trigger on the West Coast Interiors fabric kit to match the OG fabric in evidence. This needs to be replaced.
Now to get some work done. Found a local welder to make the tray and rear window repair as needed. In the meantime dealing with minor surgery so a wee bit of recovery time in order.
_________________ Scott |
|
Back to top |
|
|
djfordmanjack Samba Member
Joined: June 15, 2009 Posts: 2281 Location: Graz, Austria, Europe
|
Posted: Thu Dec 12, 2024 4:00 am Post subject: Re: New project - 1954 VW Beetle Deluxe w/ VW Canada prodn plate |
|
|
Mika has a super nice quality repair panel for your rusted section ! Would be a shame to cut what seems another really good ( even donor) body that maybe still could be used for another project in future ! 54s don't grow on trees anymore... _________________ Hotrods, Fords, Veedubs and Triumph Twins !
52 Barndoor DLX Coachbuild project
55 Wolfsburg panel project, og paint Taubenblau L31
62 Dickholmer, custom color Seeblau L360
63 1500 Notch, og paint Rubin Rot L456
67 1500 Käfer, og paint Lotus weiß L282 w/red interior |
|
Back to top |
|
|
kintail Samba Member
Joined: January 01, 2003 Posts: 659 Location: Canada
|
Posted: Thu Dec 12, 2024 7:04 am Post subject: Re: New project - 1954 VW Beetle Deluxe w/ VW Canada prodn plate |
|
|
I understand your thoughts on this as well.... a lot of vw cars and parts have disappeared over the decades. And thanks to new technology and those who have stepped up to reproduce parts accurately and affordable.
I should have taken a full picture to the extent the body has been cut before I got it. The pan is gone, and the b-pillars have been cut for the semaphores. the bottom of the body has been sitting on the ground for decades so the heat channels are rusted pretty badly. Plus the front clip cut off as well. I did order some great repair panels from Mika just as the Canada Post strike started...... Hopefully ends soon!!
The VW Canada plate was saved for the record.
_________________ Scott |
|
Back to top |
|
|
kintail Samba Member
Joined: January 01, 2003 Posts: 659 Location: Canada
|
Posted: Thu Dec 12, 2024 9:16 am Post subject: Re: New project - 1954 VW Beetle Deluxe w/ VW Canada prodn plate |
|
|
In the foreground a rare 1953 VW Custom sunroof to be restored. In the background the remains of the '54 donor body. _________________ Scott |
|
Back to top |
|
|
kintail Samba Member
Joined: January 01, 2003 Posts: 659 Location: Canada
|
Posted: Fri Dec 27, 2024 6:22 pm Post subject: Re: New project - 1954 VW Beetle Deluxe w/ VW Canada prodn plate |
|
|
Got some replacement sheet metal today from Virtanen Replacement Panels for both doors and A pillars. This was held up because of the Canada Post strike here but they arrived safely.
Found out both headlights on the car are the originals put on at the factory, noted by arrow mark on glass and two rivets on chrome headlight ring. Hopefully the stone chip on one can be reasonably repaired.
Determined that heater channels have to be replaced. Klassic panels now ordered. Discussions regarding body work continue. Ordered European bumper kit to return to original and.... birth certificate on the way!! Last time I ordered one of these they were free from VW..... oh well.[/img] _________________ Scott |
|
Back to top |
|
|
sunroof Samba Member
Joined: October 06, 2006 Posts: 1881 Location: Winnipeg
|
Posted: Tue Jan 07, 2025 5:27 pm Post subject: Re: New project - 1954 VW Beetle Deluxe w/ VW Canada prodn plate |
|
|
This is a parcel tray I cut out of a '59 that was intended for your convertible but should work in your '54. It is different from the '54 but since no one will ever see it, it should be Ok
Don _________________ Better and better mistakes! |
|
Back to top |
|
|
vw356 Samba Member
Joined: January 09, 2004 Posts: 256 Location: Cullman,Alabama
|
Posted: Tue Jan 07, 2025 5:42 pm Post subject: Re: New project - 1954 VW Beetle Deluxe w/ VW Canada prodn plate |
|
|
This clip is possibly a late '59, but I usually consider this a 1960 because of the rib differences. A '54 is completely different, but this could work. I do not think a '54 rear seat will fit with this clip installed though. In a '54, the rear cargo shelf curves sharply downwards at the front edge, then curves outward at the bottom sharply to meet the crossmembers and the whole lower area is more flat and the seat base sits on it and the seat back meets the sharp upper curve.
I can make pictures if needed of a '54 body and '54 back seat.
As correct as this car is, might as well go all the way.
Best of luck!
Don _________________ Current projects:
1950's Volkswagens!
51,52,54's,55,56's,57,58's,'60's And then a bunch of '60's, but the '50's are my favorites.. |
|
Back to top |
|
|
vw356 Samba Member
Joined: January 09, 2004 Posts: 256 Location: Cullman,Alabama
|
Posted: Tue Jan 07, 2025 5:48 pm Post subject: Re: New project - 1954 VW Beetle Deluxe w/ VW Canada prodn plate |
|
|
Oops.. I just replied impulsively seeing this latest picture in the gallery. I forgot the correct '54 package area was already posted above.
I would use that '54 donor car. Other people will want to buy the other donor clip pieces left over too.
Best of luck!
Don _________________ Current projects:
1950's Volkswagens!
51,52,54's,55,56's,57,58's,'60's And then a bunch of '60's, but the '50's are my favorites.. |
|
Back to top |
|
|
sunroof Samba Member
Joined: October 06, 2006 Posts: 1881 Location: Winnipeg
|
Posted: Tue Jan 07, 2025 7:17 pm Post subject: Re: New project - 1954 VW Beetle Deluxe w/ VW Canada prodn plate |
|
|
Quote: |
I can make pictures if needed of a '54 body and '54 back seat.
|
I actually have a 54
However I think you're right. As soon as it warms up a little I can head over to John's place and directly compare the two and figure out if the '59 tray will work or not.
Don _________________ Better and better mistakes! |
|
Back to top |
|
|
vw356 Samba Member
Joined: January 09, 2004 Posts: 256 Location: Cullman,Alabama
|
Posted: Tue Jan 07, 2025 7:32 pm Post subject: Re: New project - 1954 VW Beetle Deluxe w/ VW Canada prodn plate |
|
|
I like your '54 too!
I know your clip can weld in and look decent, but I am fairly sure the '54 back seat will not fit in with the later clip.
I do all kinds of vw welding as my hobby, and I have early beetles for each year from 1951-'60.
Still, I learn new details very often even after 30 years. We will know soon.
Thank You. _________________ Current projects:
1950's Volkswagens!
51,52,54's,55,56's,57,58's,'60's And then a bunch of '60's, but the '50's are my favorites.. |
|
Back to top |
|
|
|