Author |
Message |
Mike Edwards Samba Member
Joined: November 17, 2003 Posts: 44 Location: Charlotte, NC
|
Posted: Fri Jul 29, 2005 4:17 am Post subject: Hand Crank |
|
|
Finally got around to installing the hand crank I bought from Mike Crip last year. What a blast! I may never use the starter again.
Anyway.....
I need a way to cover the hole in the rear tin. It is right by the muffler and I don't want to draw in that hot air. Just curious what others have used.
Thanks,
Mike |
|
Back to top |
|
|
Towel Rail Horizontally Opposed
Joined: April 15, 2005 Posts: 4622 Location: SE CR IA US NA PE
|
Posted: Fri Jul 29, 2005 7:52 am Post subject: |
|
|
I plan to install a little swiveling metal piece on my tin with a bolt on one side and a little hook on the other, with some kind of rubber stopper between them.
I haven't really sketched it out well, but you get the idea. For some more vintage-approved ideas, look up "crank start tin" in the Classifieds section. |
|
Back to top |
|
|
markie61 Samba Member
Joined: April 11, 2005 Posts: 583 Location: Northern Virginia
|
Posted: Sun Feb 25, 2007 4:09 pm Post subject: |
|
|
Old thread....
New video.....
Link
Keys!!??? We don't need no stinkin' keys....!
Mark _________________ Whut is that-there Thang!?
------------------------------
Chicks dig my Thing - so what if it's little and yellow...!? |
|
Back to top |
|
|
Towel Rail Horizontally Opposed
Joined: April 15, 2005 Posts: 4622 Location: SE CR IA US NA PE
|
Posted: Sun Feb 25, 2007 4:39 pm Post subject: |
|
|
Coolness! I had not yet seen that video!
Since my earlier post, I discovered that my frame horns were sprung enough that my engine was too misaligned to use the crank. I'll have to wait until after the resto to crank-start this Thing... _________________ 1974 Thing -- under the knife
1967 Beetle -- spring/summer/fall driver
1996 Subaru OBW (EJ22, 5-speed, AWD) -- winter car, 3-seasons "don't feel like biking today" car
049 > 070 > 053 > 009 |
|
Back to top |
|
|
Go-SpeedRacer Samba Member
Joined: December 31, 2006 Posts: 79
|
Posted: Sun Feb 25, 2007 6:16 pm Post subject: |
|
|
You see where those tail lights are mounted, is that a Euro set up, not only are they bus tail lights, I assume but, they are down close to the bumper in lieu of up high on the slanted part. Looks pretty clean. |
|
Back to top |
|
|
markie61 Samba Member
Joined: April 11, 2005 Posts: 583 Location: Northern Virginia
|
Posted: Sun Feb 25, 2007 7:59 pm Post subject: |
|
|
Go-SpeedRacer wrote: |
You see where those tail lights are mounted, is that a Euro set up, not only are they bus tail lights, I assume but, they are down close to the bumper in lieu of up high on the slanted part. Looks pretty clean. |
The spoken German on the video is another clue that it is a European vehicle . I prefer the look of the orginal lights down low over the elephant feet up high on US models, but think the slickest are the aftermarket flat ones up high.
Mark _________________ Whut is that-there Thang!?
------------------------------
Chicks dig my Thing - so what if it's little and yellow...!?
Last edited by markie61 on Mon Feb 26, 2007 5:58 am; edited 1 time in total |
|
Back to top |
|
|
Ferretkona Samba Member
Joined: December 03, 2005 Posts: 1306 Location: Columbia, CA
|
Posted: Sun Feb 25, 2007 8:37 pm Post subject: |
|
|
Go-SpeedRacer wrote: |
You see where those tail lights are mounted, is that a Euro set up, not only are they bus tail lights, I assume but, they are down close to the bumper in lieu of up high on the slanted part. Looks pretty clean. |
All Things, 181, 182 (or whatever names were used) previous to our imported 73's and 74's came with the bus lights. 73 buses did not use them either. |
|
Back to top |
|
|
Woreign Samba Member
Joined: June 04, 2006 Posts: 2841 Location: Crestview FL
|
Posted: Mon Feb 26, 2007 6:11 am Post subject: |
|
|
It's a shame that the North American models didn't come with the crank... Probably because VW was afraid that someone would hurt themself and want to sue, or we're too lazy to use a crank and are expected to call roadside service!
By the way, what does the kit consist of? A crank, special drive pulley nut, and a rear engine tin with a hole in it? |
|
Back to top |
|
|
markie61 Samba Member
Joined: April 11, 2005 Posts: 583 Location: Northern Virginia
|
Posted: Mon Feb 26, 2007 6:55 am Post subject: |
|
|
It also looks like like the crank handle itself has some sort of ratching mechanism/freewheel built in so the crank doesn't spin with the running engine and take someone's head off.
Mark _________________ Whut is that-there Thang!?
------------------------------
Chicks dig my Thing - so what if it's little and yellow...!? |
|
Back to top |
|
|
Towel Rail Horizontally Opposed
Joined: April 15, 2005 Posts: 4622 Location: SE CR IA US NA PE
|
Posted: Mon Feb 26, 2007 7:29 am Post subject: |
|
|
markie61 wrote: |
It also looks like like the crank handle itself has some sort of ratching mechanism/freewheel built in so the crank doesn't spin with the running engine and take someone's head off.
Mark |
Nope. That's built into the nut. There are "ramps" built into the side of the nut that keep it from engaging with the crank once the engine is moving faster than the crank.
_________________ 1974 Thing -- under the knife
1967 Beetle -- spring/summer/fall driver
1996 Subaru OBW (EJ22, 5-speed, AWD) -- winter car, 3-seasons "don't feel like biking today" car
049 > 070 > 053 > 009 |
|
Back to top |
|
|
markie61 Samba Member
Joined: April 11, 2005 Posts: 583 Location: Northern Virginia
|
Posted: Mon Feb 26, 2007 9:06 am Post subject: |
|
|
Oh....in the video, it sounded like some sort of ratcheting sound.
Yeah, I'll bet that crank setup has more potential for hitting someone in the head than a gas heater blowing up...
Mark _________________ Whut is that-there Thang!?
------------------------------
Chicks dig my Thing - so what if it's little and yellow...!? |
|
Back to top |
|
|
oorwullie Samba Member
Joined: May 01, 2003 Posts: 2365 Location: fribourg,switzerland
|
Posted: Mon Feb 26, 2007 10:35 am Post subject: |
|
|
markie61 wrote: |
Yeah, I'll bet that crank setup has more potential for hitting someone in the head than a gas heater blowing up.
Mark |
not really, it's pretty foolproof provided you don't have your thumb around the handle and it kicks back!
i was rooting around in one of my sheds last week and discovered (among other things)2 more cranks i'd forgotten about. i think the bent one is from my 65 army bus(used regularly till i converted to 12v) and that the shorter one is from a 63 army bus i broke about 15 years ago, but it might be an original trekker one.
|
|
Back to top |
|
|
Towel Rail Horizontally Opposed
Joined: April 15, 2005 Posts: 4622 Location: SE CR IA US NA PE
|
Posted: Thu Mar 08, 2007 12:23 am Post subject: |
|
|
oorwullie wrote: |
i was rooting around in one of my sheds last week and discovered (among other things)2 more cranks i'd forgotten about. i think the bent one is from my 65 army bus(used regularly till i converted to 12v) and that the shorter one is from a 63 army bus i broke about 15 years ago, but it might be an original trekker one.
|
That longer one looks like it could work for a beetle (assuming you straightened it.) _________________ 1974 Thing -- under the knife
1967 Beetle -- spring/summer/fall driver
1996 Subaru OBW (EJ22, 5-speed, AWD) -- winter car, 3-seasons "don't feel like biking today" car
049 > 070 > 053 > 009 |
|
Back to top |
|
|
lukesky Samba Member
Joined: July 12, 2006 Posts: 246 Location: See The Rabbits, IA
|
Posted: Thu Mar 08, 2007 9:24 pm Post subject: |
|
|
As far as the cover for the hole in the bumper (Towel Rail, you've seen this), the P.O. of mine took an old round trailer light plug socket and screwed it on into the hole, making it look like you'd plug the trailer lights in there. Of course, it took me a while (and TRail's help) to figure that with no trailer hitch and none of the wires being connected, it was unlikely that anyone would ever plug anything into it.
I have replaced it with a newer VW emblem. _________________ You get what you get, and you don't throw a fit.
-Gabi |
|
Back to top |
|
|
oorwullie Samba Member
Joined: May 01, 2003 Posts: 2365 Location: fribourg,switzerland
|
Posted: Fri Mar 09, 2007 1:35 am Post subject: |
|
|
i'll post a pic of the original rear tin with crank hole later. |
|
Back to top |
|
|
oorwullie Samba Member
Joined: May 01, 2003 Posts: 2365 Location: fribourg,switzerland
|
Posted: Fri Mar 09, 2007 6:05 am Post subject: |
|
|
|
|
Back to top |
|
|
Video Bob Samba Member
Joined: November 03, 2005 Posts: 261 Location: Bishop, GA
|
Posted: Fri Mar 09, 2007 1:15 pm Post subject: |
|
|
Having been raised in the dark ages, when tractors were started with a crank, I offer this bit of information. Do not wrap your thumb around the crank handle. Place all fingers and thumb on the same side of the crank handle. Thus if the engine backfires, it will not break your thumb on the reverse spin. Age sometimes has it's benefits _________________ Ya can't have too many Vdubs!
1956 Oval
1966 Beetle
1974 Thing
1974 Super Beetle
1976 Westy P22 |
|
Back to top |
|
|
oorwullie Samba Member
Joined: May 01, 2003 Posts: 2365 Location: fribourg,switzerland
|
Posted: Sat Mar 10, 2007 11:28 am Post subject: |
|
|
Video Bob wrote: |
Having been raised in the dark ages, when tractors were started with a crank, I offer this bit of information. Do not wrap your thumb around the crank handle. Place all fingers and thumb on the same side of the crank handle. Thus if the engine backfires, it will not break your thumb on the reverse spin. Age sometimes has it's benefits |
this is true.
i learned at an early age with cement mixers and dumper trucks on building sites. |
|
Back to top |
|
|
pewe_kodok Samba Member
Joined: October 15, 2006 Posts: 64 Location: Bandung, West Java, Indonesia
|
Posted: Thu Mar 22, 2007 1:10 am Post subject: |
|
|
where i can get hand crank set? like special nut, and crank arm |
|
Back to top |
|
|
|