Hello! Log in or Register   |  Help  |  Donate  |  Buy Shirts New!  See all banner ads | Advertise on TheSamba.com  
TheSamba.com
 
retrofitting Air Conditioning
Page: Previous  1, 2
Forum Index -> Vanagon Share: Facebook Twitter
Reply to topic
Print View
Quick sort: Show newest posts on top | Show oldest posts on top View previous topic :: View next topic  
Author Message
mickeyflorio
Samba Member


Joined: July 05, 2009
Posts: 10
Location: Denver
mickeyflorio is offline 

PostPosted: Tue Sep 13, 2011 7:36 pm    Post subject: Reply with quote

Thanks for all the advice! Sounds like Vintage Air is the way to go. Still not clear on how much surgery is required for Gen II vs Gen IV. Specifically, which systems require you to lose the ashtray, radio and/or glove compartment?

rsxsr: where did you get those great vents? (I'd need black)

edgood1: I followed your poptop-grafting project. We'll all be grateful if you document your A/C install in as much detail!
Back to top
View user's profile Send private message Classifieds Feedback
MarkWard
Samba Member


Joined: February 09, 2005
Posts: 15080
Location: Palm Beach County, Florida
MarkWard is offline 

PostPosted: Wed Sep 14, 2011 7:23 am    Post subject: Reply with quote

The center vents are from Vintage Air as well. They match the outers the closest. As far as surgery and the Gen II. I had to drill holes in the front firewall for the two AC hoses. Rather than doing complete hose runs through the firewall, I used a bulkhead fitting instead. This allowed me to get the interior finished up and then move on to the condensor, compressor, dryer and hoses, but still have the van driveable. Once the dash is back in, you can't access the AC hoses.

I had to drill two holes for the evaporator drain. One in the cross member where the evap sits, and one through the floor under the member. Drains near the spare tire. The 82 has the coolant hoses on the passenger floor so my AC drain is next to them.

I needed to drill some small holes for mounting relays dryer etc. For blocking the fresh air intake, I used an aluminum .063" plate with weather strip tape and the original heater housing mounting bolts. I had to notch two of the braces on the underside of the dash board to insure the vent hoses would not be jammed when the dash was put pack in.
I also needed to enlarge the radio hole and the factory control cutouts in the dashboard.

So I would call it minimal surgery. I have a zip file of my installation if you would like to see a little more of my install. PM me your email address and I can email the file to you. I could not see the sense in uploading all the pictures here. mark
_________________
1982 Vanagon Camper with ALH TDI.

In Car https://youtu.be/5hbfdUJR88Q
Back to top
View user's profile Send private message Gallery Classifieds Feedback
thummmper
Samba Member


Joined: November 25, 2009
Posts: 2015
Location: Meadow Valley, California Republic
thummmper is offline 

PostPosted: Fri Sep 16, 2011 10:08 am    Post subject: Reply with quote

hope these help a little
Image may have been reduced in size. Click image to view fullscreen.

Image may have been reduced in size. Click image to view fullscreen.
Back to top
View user's profile Send private message Visit poster's website Gallery Classifieds Feedback
Display posts from previous:   
Reply to topic    Forum Index -> Vanagon All times are Mountain Standard Time/Pacific Daylight Savings Time
Page: Previous  1, 2
Page 2 of 2

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum

About | Help! | Advertise | Donate | Premium Membership | Privacy/Terms of Use | Contact Us | Site Map
Copyright © 1996-2020, Everett Barnes. All Rights Reserved.
Not affiliated with or sponsored by Volkswagen of America | Forum powered by phpBB