Author |
Message |
cecil Samba Member
Joined: February 23, 2005 Posts: 461 Location: Stockton, CA
|
Posted: Fri Jul 24, 2015 1:27 pm Post subject: Move seats back |
|
|
I need to increase my leg room by at least 2 inches. As it is my legs are scrunched up like a clown car. currently using 71 beetle high back with new covers which I don't want to change.
Suggestions on best way to do this. _________________ I may not be that funny or athletic or good looking or smart or talented....I forgot where I was going with this
I have this wierd desease called "must tear everything up and put it back together when there's nothing wrong with it...Itus." |
|
Back to top |
|
|
KAmes Samba Member
Joined: February 16, 2014 Posts: 877 Location: Illinois
|
Posted: Fri Jul 24, 2015 5:40 pm Post subject: |
|
|
Here's the idea I was thinking about, mind you I've not ever done it, there may be some reason it won't work. Think about the rear of the seat part of the track and where it contacts the tabs at the rear of the floor part of the track, preventing it going back farther. What if you notched out part of, say two inches, of the seat part of the track allowing it to progress rearward a little farther. There would be a point where it would be too much, as the seat would be effectively off the back of the track, but I wonder if an inch or two would be ok. Idea two: Maybe get some floor track pieces and lengthen it? Obvious solution is cut the track off the floor and re weld, but maybe it could be solved without the mess and destruction. Good luck! |
|
Back to top |
|
|
HIGHTOWER Samba Member
Joined: June 06, 2007 Posts: 20 Location: California SF
|
Posted: Sat Jul 25, 2015 2:27 am Post subject: seat |
|
|
This is what i did.cut of te stop at de track on the chassis.then you can go allot more backwards but it wil not stay if you have to brake hard.
I fabricated a pice that i welded to the seat trak so i can lock it in posision. _________________ Quallity is never an accident! |
|
Back to top |
|
|
cecil Samba Member
Joined: February 23, 2005 Posts: 461 Location: Stockton, CA
|
Posted: Sat Jul 25, 2015 11:16 am Post subject: |
|
|
I cut the stop off and pushed the seat back ~ 1 inch. More comfortable. If I need more i will re-locate rails. Thanks for the idea. _________________ I may not be that funny or athletic or good looking or smart or talented....I forgot where I was going with this
I have this wierd desease called "must tear everything up and put it back together when there's nothing wrong with it...Itus." |
|
Back to top |
|
|
jjrannauro Samba Member
Joined: June 30, 2011 Posts: 217 Location: MEXICO
|
Posted: Sat Jul 25, 2015 11:46 am Post subject: |
|
|
I think it would be best if you unweld the seat track and move it backwards where it is right for you and weld it back to the floor.
When I restored my Thing, I use 4 screws for each seat track and screw the seat tracks to the floor and they work fine for me.
|
|
Back to top |
|
|
CraigInPA Samba Member
Joined: March 09, 2011 Posts: 212 Location: Norristown, PA
|
Posted: Sun Jul 26, 2015 2:54 am Post subject: |
|
|
jjrannauro wrote: |
I think it would be best if you unweld the seat track and move it backwards where it is right for you and weld it back to the floor.
When I restored my Thing, I use 4 screws for each seat track and screw the seat tracks to the floor and they work fine for me.
|
From the pics, it looks like you're using carriage bolts to hold the seats down, not metal screws. For clarification for future readers, sheet metal screws will not hold the seats in place during a collision, and will loosen over time. For seats, you should have a through-floor connection. i.e., a wide head bolt, and a large washer and nut underneath the floor. The large washer is there to spread the load in the event of a collision.
Craig |
|
Back to top |
|
|
GI Joe Samba Member
Joined: April 28, 2005 Posts: 2012 Location: Athens, TN
|
Posted: Sun Jul 26, 2015 4:13 pm Post subject: |
|
|
Lost in translation..
CraigInPA wrote: |
jjrannauro wrote: |
I think it would be best if you unweld the seat track and move it backwards where it is right for you and weld it back to the floor.
When I restored my Thing, I use 4 screws for each seat track and screw the seat tracks to the floor and they work fine for me.
|
From the pics, it looks like you're using carriage bolts to hold the seats down, not metal screws. For clarification for future readers, sheet metal screws will not hold the seats in place during a collision, and will loosen over time. For seats, you should have a through-floor connection. i.e., a wide head bolt, and a large washer and nut underneath the floor. The large washer is there to spread the load in the event of a collision.
Craig |
_________________ '74 Thing, "Our Thing"....
http://www.thesamba.com/vw/forum/viewtopic.php?t=4...p;start=60
'71 Beetle RPU
http://www.thesamba.com/vw/forum/viewtopic.php?p=8080337#8080337
www.NLEOMF.com
Respect, Honor, Remember |
|
Back to top |
|
|
jjrannauro Samba Member
Joined: June 30, 2011 Posts: 217 Location: MEXICO
|
Posted: Mon Jul 27, 2015 8:35 am Post subject: |
|
|
Thanks for pointed it out, you are right, I forgot to mention that I reinforced the floor underneath with metal and changed the screws for the same reason.
Greetings.
GI Joe wrote: |
Lost in translation..
CraigInPA wrote: |
jjrannauro wrote: |
I think it would be best if you unweld the seat track and move it backwards where it is right for you and weld it back to the floor.
When I restored my Thing, I use 4 screws for each seat track and screw the seat tracks to the floor and they work fine for me.
|
From the pics, it looks like you're using carriage bolts to hold the seats down, not metal screws. For clarification for future readers, sheet metal screws will not hold the seats in place during a collision, and will loosen over time. For seats, you should have a through-floor connection. i.e., a wide head bolt, and a large washer and nut underneath the floor. The large washer is there to spread the load in the event of a collision.
Craig |
|
|
|
Back to top |
|
|
|