Author |
Message |
Mr Orange Samba Member
Joined: September 30, 2011 Posts: 64 Location: Göteborg SWEDEN
|
Posted: Tue Jun 12, 2012 10:14 pm Post subject: Cargo floor seat mounts |
|
|
Hi All,
I've got my Klassic Fab cargo floor the other day. When I unpacked I was a little surprised as there was no seat mounts for the middle seat included.
So I have some questions for you:
1) The mounts marked A is for the rear seat. But what are the recessions in front of them for?
2) The recesses marked B is for the wide middle seat. Right? And the brackets is the same that goes on A?
3) There is a plate missing at C, right? Can you buy this reproduced?
Thanks for any input,
Jörgen Forssling
SWEDEN |
|
Back to top |
|
|
EverettB Administrator
Joined: April 11, 2000 Posts: 69802 Location: Phoenix Metro
|
|
Back to top |
|
|
Mr Orange Samba Member
Joined: September 30, 2011 Posts: 64 Location: Göteborg SWEDEN
|
Posted: Tue Jun 12, 2012 11:12 pm Post subject: |
|
|
It is supposed to be a 66 floor. I'll have to check with my supplier. Is the 66 floor the same? What kind of seat mount brackets goes on a 66 floor?
Thanks for your input!
//Jörgen |
|
Back to top |
|
|
Gmiee5 Samba Member
Joined: December 06, 2008 Posts: 388 Location: Portland Oregon
|
Posted: Wed Jun 13, 2012 12:05 am Post subject: |
|
|
I'm sure Gerson still sells them.
I picked mine up about 2 years ago from him
_________________ _______________________ |
|
Back to top |
|
|
Mr Orange Samba Member
Joined: September 30, 2011 Posts: 64 Location: Göteborg SWEDEN
|
Posted: Wed Jun 13, 2012 12:33 am Post subject: |
|
|
Is your bus a 66 or 67?
Thanks,
Jörgen |
|
Back to top |
|
|
Gmiee5 Samba Member
Joined: December 06, 2008 Posts: 388 Location: Portland Oregon
|
Posted: Wed Jun 13, 2012 12:34 am Post subject: |
|
|
67
before
_________________ _______________________ |
|
Back to top |
|
|
Mr Orange Samba Member
Joined: September 30, 2011 Posts: 64 Location: Göteborg SWEDEN
|
Posted: Wed Jun 13, 2012 12:48 am Post subject: |
|
|
Can someone post a pic of a 66 floor.
Thanks,
Jörgen |
|
Back to top |
|
|
Mr Orange Samba Member
Joined: September 30, 2011 Posts: 64 Location: Göteborg SWEDEN
|
Posted: Wed Jun 13, 2012 11:18 pm Post subject: |
|
|
Can someone post a pic on a 66 floor so I can get the right kind of seat mounts.
Thanks,
Jörgen |
|
Back to top |
|
|
olliehank47 Samba Member
Joined: May 04, 2011 Posts: 1198
|
Posted: Thu Jun 14, 2012 7:53 am Post subject: |
|
|
Mr Orange wrote: |
Can someone post a pic on a 66 floor so I can get the right kind of seat mounts.
Thanks,
Jörgen |
The seat mounts you need will be the plates shown in the photo posted by Gmiee5. You will need to determine what middle seat you have--full width or 2/3rds. If you have a full seat, you will need all four plates. If you have a 2/3rds seat, you need three plates, leaving out the one closest to the cargo doors.
The only difference between a 66/earlier floor and the 67 shown (with regard to anchor plates) is the 67 has all four plates installed regardless of the seat ordered with the bus.
Use the photo posted by Everett to orient the plates correctly. The round holes in the plates are toward the center line of the cargo floor. |
|
Back to top |
|
|
Mr Orange Samba Member
Joined: September 30, 2011 Posts: 64 Location: Göteborg SWEDEN
|
Posted: Thu Jun 14, 2012 9:58 am Post subject: |
|
|
Thanks!
My bus is a full width middle seat. I'm not too concerned about originality. But from what I could see, I did not have the big plates. I rescued at least three of the mounts. Two at the most rear and one for the middle seat.
Gerson has sent me a PM that he will ship me the hardware. That is a stand up guy!
Just for the nerds I post some pics of my old rotten floor. Please tell me what you think regarding the mounts. Can it be that mine is an early 66? (mid august production)
Thanks all!
Jörgen
|
|
Back to top |
|
|
Mr Orange Samba Member
Joined: September 30, 2011 Posts: 64 Location: Göteborg SWEDEN
|
Posted: Thu Jun 28, 2012 5:33 am Post subject: |
|
|
Hi All!
I got my seat mount plates from Gerson yesterday.
How were they fastened originally? Spot welds?
Thanks for any input,
Jörgen |
|
Back to top |
|
|
Kchulick Samba Member
Joined: October 27, 2004 Posts: 47 Location: Cumming, GA
|
Posted: Sun Apr 06, 2014 9:10 pm Post subject: |
|
|
I was told these were seat mounts for my middle seat? Then again my order got a little messed up and I have not been able to get a response from anyone at Klassic Fab over what these pieces are.
_________________ ChuforiaGraffix.com
Graphics, clear bras, apparel, vehicle wraps, decals, and toilet monsters. |
|
Back to top |
|
|
KOMBI NIKO Samba Member
Joined: February 03, 2013 Posts: 277 Location: Australia
|
|
Back to top |
|
|
EverettB Administrator
Joined: April 11, 2000 Posts: 69802 Location: Phoenix Metro
|
|
Back to top |
|
|
EverettB Administrator
Joined: April 11, 2000 Posts: 69802 Location: Phoenix Metro
|
|
Back to top |
|
|
Kchulick Samba Member
Joined: October 27, 2004 Posts: 47 Location: Cumming, GA
|
Posted: Wed May 21, 2014 5:38 pm Post subject: |
|
|
Well I'll be darned. Those look like the pics of the pieces I posted above. Thanks for posting. After many attempts to contact Klassic Fab I never got any kind of response to multiple emails to multiple email addresses, and phone #'s.
Still would need to see how they function, but nice to at least seem there where they go. _________________ ChuforiaGraffix.com
Graphics, clear bras, apparel, vehicle wraps, decals, and toilet monsters. |
|
Back to top |
|
|
lumber-baron Samba Member
Joined: May 01, 2010 Posts: 394 Location: Golden, CO
|
Posted: Sat Dec 19, 2015 12:14 pm Post subject: Re: Cargo floor seat mounts |
|
|
Has anyone run into this problem?
The right mounting location for the short middle seat is 4" right of where it should be.
This should measure 42".
WTF GERSON???
:snipersmile: :snipersmile: :snipersmile:
|
|
Back to top |
|
|
Stanagon Samba Member
Joined: July 11, 2003 Posts: 4186 Location: Boston, MA
|
|
Back to top |
|
|
lumber-baron Samba Member
Joined: May 01, 2010 Posts: 394 Location: Golden, CO
|
Posted: Sat Dec 19, 2015 1:22 pm Post subject: Re: Cargo floor seat mounts |
|
|
It's a 59-66. |
|
Back to top |
|
|
flemcadiddlehopper Samba Member
Joined: December 05, 2011 Posts: 2332 Location: Kelowna, BC. Canada.
|
Posted: Sat Dec 19, 2015 1:33 pm Post subject: Re: Cargo floor seat mounts |
|
|
I had my floor replaced in my '67 ( not classic Fab) and the mounting locations were wrong for my 2/3 middle seat. I had to flatten the areas in the correct locations and weld in the mounting plates.
The die made to hammer on.
A look after hammering done.
Plates set in place
Painted, done.
Not a factory correct thing, but it will hold my seat in place. Yes I know...wavy floor, again not funky green...get what you pay for.
Gordo. _________________ Everybody Dies....Some Never Live.
Retrograde Garage. Vintage Aircooled, and others. |
|
Back to top |
|
|
|