Author |
Message |
Mattasmith12 Samba Member
Joined: June 22, 2015 Posts: 2
|
Posted: Thu Jun 30, 2016 2:38 pm Post subject: Corrosion around cylinder bores |
|
|
I have a case that was cleaned and bored for 90.5 cylinders. Unfortunately, the machine shop found some corrosion around the bores. Am I right to assume this case is garbage now since the cylinders won't seal correctly?
|
|
Back to top |
|
|
miniman82 Samba Swamp Donkey
Joined: March 22, 2005 Posts: 9515 Location: Southern Maryland
|
Posted: Thu Jun 30, 2016 3:05 pm Post subject: Re: Corrosion around cylinder bores |
|
|
It'll seal fine, why wouldn't it? None of that damage connects a point from inside the engine to the outside, and you're going to use sealant anyway. I've always used silicone in this area of the engine, but nowhere else! _________________ Build thread: http://www.thesamba.com/vw/forum/viewtopic.php?t=212747
Glenn wrote: |
satterley_sr wrote: |
I just wanted to bitch but I'm getting no sympathy. |
Welcome to the Samba. |
|
|
Back to top |
|
|
vwracerdave Samba Member
Joined: November 11, 2004 Posts: 15303 Location: Deep in the 405
|
Posted: Thu Jun 30, 2016 3:38 pm Post subject: Re: Corrosion around cylinder bores |
|
|
I'd run it. It is not in a pressurized oil stream so the silicone will do it's job and seal it up. _________________ 2017 Street Comp Champion - Thunder Valley Raceway Park - Noble, OK
2010 Sportsman ET Champion - Mid-America Dragway - Arkansas City, KS
1997 Sportsman ET Champion - Thunder Valley Raceway Park - Noble ,OK
Featured in Dec. 2001 HOT VW's Magazine page 63
Watch my racing video's http://www.youtube.com/user/okvwracer/videos |
|
Back to top |
|
|
Mattasmith12 Samba Member
Joined: June 22, 2015 Posts: 2
|
Posted: Thu Jun 30, 2016 3:53 pm Post subject: Re: Corrosion around cylinder bores |
|
|
Thanks for the input! That turned my day around. I'll move forward as planned. |
|
Back to top |
|
|
powerbee1 Samba Member
Joined: November 13, 2011 Posts: 8 Location: Sonoma, CA
|
Posted: Thu Jun 30, 2016 4:23 pm Post subject: Re: Corrosion around cylinder bores |
|
|
cut deck .100 use spacer for right deck height:D |
|
Back to top |
|
|
modok Samba Member
Joined: October 30, 2009 Posts: 26781 Location: Colorado Springs
|
Posted: Thu Jun 30, 2016 4:33 pm Post subject: Re: Corrosion around cylinder bores |
|
|
it's alrady cut .040 approx
dab 518 in the pot-holes, it'll work |
|
Back to top |
|
|
miniman82 Samba Swamp Donkey
Joined: March 22, 2005 Posts: 9515 Location: Southern Maryland
|
Posted: Fri Jul 01, 2016 12:01 pm Post subject: Re: Corrosion around cylinder bores |
|
|
Whoever did that must have a pretty sharp flycutter for it to clean up that good, looking at it beforehand I bet you didn't think it would turn out that clean. _________________ Build thread: http://www.thesamba.com/vw/forum/viewtopic.php?t=212747
Glenn wrote: |
satterley_sr wrote: |
I just wanted to bitch but I'm getting no sympathy. |
Welcome to the Samba. |
|
|
Back to top |
|
|
mark tucker Samba Member
Joined: April 08, 2009 Posts: 23937 Location: SHALIMAR ,FLORIDA
|
Posted: Fri Jul 01, 2016 5:26 pm Post subject: Re: Corrosion around cylinder bores |
|
|
looks like a good job but should of went about .040 farther. shims are sheep...and seals are wet....unless there sunning them selves. |
|
Back to top |
|
|
Rome Samba Member
Joined: June 02, 2004 Posts: 9640 Location: Pearl River, NY
|
Posted: Fri Jul 01, 2016 6:11 pm Post subject: Re: Corrosion around cylinder bores |
|
|
matta, very good work with your photos- sharp, well lit. Wish I could reach thru the computer and run my fingers lightly over the machined surfaces. |
|
Back to top |
|
|
bugguy1967 Samba Member
Joined: January 16, 2008 Posts: 4341 Location: Los Angeles, CA 90016
|
Posted: Sat Jul 02, 2016 9:04 am Post subject: Re: Corrosion around cylinder bores |
|
|
Who did that machine work? Looks like EMW in Hawthorne. |
|
Back to top |
|
|
rs58rag Samba Member
Joined: August 22, 2010 Posts: 419 Location: riverside,ca
|
Posted: Sat Jul 02, 2016 11:13 am Post subject: Re: Corrosion around cylinder bores |
|
|
Permatex ultra copper silicone to seal cylinders to case.... |
|
Back to top |
|
|
|