Author |
Message |
xmass Samba Member
Joined: March 30, 2017 Posts: 3 Location: St-canut
|
Posted: Thu Mar 30, 2017 7:13 am Post subject: Re: Ez30d harness |
|
|
Hi i'm in the process of swapping my 2.1wasserboxer for a subaru ez30D 2001 and i can't seem to find info on how to adapt the harness for the vanagon.
Ive seen for all the other subaru engine exept for H6.
Even if a will figure it by my self ( as an aicraft mechanic for 23 yrs i'm very resourceful ) it woud be nice to have couple hits and a pin out chart for the ecu.
I want to also install the subaru cruise control onto my westy at the same time.
If you guys have info on this please feel free to comment.
Thanks |
|
Back to top |
|
|
levi Samba Member
Joined: February 11, 2005 Posts: 5522 Location: Las Vegas
|
Posted: Thu Mar 30, 2017 12:27 pm Post subject: Re: My H6 Install (EZ30) |
|
|
I don't have the pinout info, but your fellow Canadian Tom shiels does.
Just Google tom shiels Subaru wiring harness. _________________ One of these days I'm gonna settle down,
but till I do I won't be hangin round.
Going down that long lonesome highway,
gonna see life my way
https://youtu.be/cSrL0BXsO40 |
|
Back to top |
|
|
xmass Samba Member
Joined: March 30, 2017 Posts: 3 Location: St-canut
|
Posted: Thu Mar 30, 2017 5:30 pm Post subject: Re: My H6 Install (EZ30) |
|
|
Than'k levi, lot's of info on tom sheild'd site 😁😁
Merci!😉 |
|
Back to top |
|
|
wesitarz Samba Member
Joined: August 20, 2012 Posts: 1491 Location: Victoria,B.C.Canada
|
|
Back to top |
|
|
kpsamba Samba Member
Joined: September 15, 2007 Posts: 6
|
Posted: Wed Jan 31, 2018 5:24 pm Post subject: Re: My H6 Install (EZ30) |
|
|
Help! Need info as to how to connect Vanagon front and rear heater hoses and coolant fill tank to Subaru H6 3.0L engine heater hose connectors.!
Presently I have the coolant fill reservoir in parallel with the heater hoses and the flow of hot coolant to the front heater is extremely marginal/slow! |
|
Back to top |
|
|
wesitarz Samba Member
Joined: August 20, 2012 Posts: 1491 Location: Victoria,B.C.Canada
|
Posted: Wed Jan 31, 2018 7:32 pm Post subject: Re: My H6 Install (EZ30) |
|
|
Do you have a diagram of your cooling system? |
|
Back to top |
|
|
piledriver Samba Member
Joined: June 05, 2003 Posts: 184 Location: In my bunker, beside my wall. (Howe, Tx)
|
Posted: Tue Dec 01, 2020 3:45 pm Post subject: Re: My H6 Install (EZ30) |
|
|
Awesome thread...
2 questions:
I'm stuffing a 3.6 in my 86 Wolfie "shed".
Will be using the RMW mountbar.
Will the 3.0/3.6 take the same mounts and steel mount plates as the 2.5?
The "square" earlier mounts seem to be greatly preferred, perhaps even the group N versions.
question#2: who makes (or made) this 3.0/3.6 header shown earlier in thread???
I have an Evil Plan to modify an existing common header for a flat 6, but if somebody is actually making one that fits that would be preferred.
_________________ Current daily driver---73 Square, 1.8L T4, MS3+MS3X/sequential w/LS2 coils 80 miles/day. |
|
Back to top |
|
|
|