Hello! Log in or Register   |  Help  |  Donate  |  Buy Shirts See all banner ads | Advertise on TheSamba.com  
TheSamba.com
 
Restoring hardware, what is your chosen finish?
Forum Index -> General/Chat Share: Facebook Twitter
Reply to topic
Print View
Quick sort: Show newest posts on top | Show oldest posts on top View previous topic :: View next topic  
Author Message
vwtrey
Samba Member


Joined: May 18, 2004
Posts: 587
Location: NM
vwtrey is offline 

PostPosted: Fri Nov 24, 2017 11:25 am    Post subject: Restoring hardware, what is your chosen finish? Reply with quote

Today, I have a pile of rusty bolts soaking in vinegar. Once these are cleaned, I will need a way to protect them. I don't care for painting bolts. I've never had results that I like. I considered getting an electroplating kit. What method do you prefer? Is there something that gives good results that I should try?
Back to top
View user's profile Send private message Facebook Gallery Classifieds Feedback
heimlich Premium Member
VWNOS.com


Joined: November 20, 2016
Posts: 6554
Location: Houston, Texas
heimlich is offline 

PostPosted: Fri Nov 24, 2017 11:27 am    Post subject: Re: Restoring hardware, what is your chosen finish? Reply with quote

How much do you want to spend?

Some kits are probably better than others. You can make your own kit from Amazon/Lowes/Home Depot/etc.
_________________
www.vwnos.com [email protected]
Classic Brands. Classic Quality.
Not all parts are made the same. NOS OE/OEM parts made mainly in West Germany, Early Germany, and Early Brazil are where VW produced the best quality parts and best fitting products.
5% Off your order with coupon code: 5%OFF
Restored Distributors Available (<--Click here)
Back to top
View user's profile Send private message Send e-mail Visit poster's website Gallery Classifieds Feedback
vwtrey
Samba Member


Joined: May 18, 2004
Posts: 587
Location: NM
vwtrey is offline 

PostPosted: Fri Nov 24, 2017 11:29 am    Post subject: Re: Restoring hardware, what is your chosen finish? Reply with quote

The kits I saw were 200ish. I'm not opposed to spending that if it does all the hardware. I've never used one before, so I don't know what to expect. This isn't going to be a show quality restoration.
Back to top
View user's profile Send private message Facebook Gallery Classifieds Feedback
heimlich Premium Member
VWNOS.com


Joined: November 20, 2016
Posts: 6554
Location: Houston, Texas
heimlich is offline 

PostPosted: Fri Nov 24, 2017 11:57 am    Post subject: Re: Restoring hardware, what is your chosen finish? Reply with quote

You can buy the pieces for less than 200. The only piece that may be a bit pricy is the power source.

I would say you can make your own kit for $50 easily. You'll want to clean the bolts immediately before putting them in the solution with muriatic acid. You can buy a gallon from Lowe's.
_________________
www.vwnos.com [email protected]
Classic Brands. Classic Quality.
Not all parts are made the same. NOS OE/OEM parts made mainly in West Germany, Early Germany, and Early Brazil are where VW produced the best quality parts and best fitting products.
5% Off your order with coupon code: 5%OFF
Restored Distributors Available (<--Click here)
Back to top
View user's profile Send private message Send e-mail Visit poster's website Gallery Classifieds Feedback
Mike Fisher
Samba Member


Joined: January 30, 2006
Posts: 17962
Location: Eugene, OR
Mike Fisher is offline 

PostPosted: Fri Nov 24, 2017 12:04 pm    Post subject: Re: Restoring hardware, what is your chosen finish? Reply with quote

Home made kit probably gives similar results to factory kits.
https://www.google.com/search?q=home+made+electrop...fox-b-1-ab
_________________
https://imgur.com/user/FisherSquareback/posts
69 FI/AT square Daily Driver
66 sunroof,67,70,71,71,71AT,72,72AT,73 Parts
two 57 oval ragtops sold
'68 Karmann Ghia sold

Society is like stew. If you don't keep it stirred up you end up with a lot of scum on the top! - Russ_Wolfe/Edward Abbey
Back to top
View user's profile Send private message Send e-mail Facebook Gallery Classifieds Feedback
heimlich Premium Member
VWNOS.com


Joined: November 20, 2016
Posts: 6554
Location: Houston, Texas
heimlich is offline 

PostPosted: Fri Nov 24, 2017 12:06 pm    Post subject: Re: Restoring hardware, what is your chosen finish? Reply with quote

I made my own. It works very well.
_________________
www.vwnos.com [email protected]
Classic Brands. Classic Quality.
Not all parts are made the same. NOS OE/OEM parts made mainly in West Germany, Early Germany, and Early Brazil are where VW produced the best quality parts and best fitting products.
5% Off your order with coupon code: 5%OFF
Restored Distributors Available (<--Click here)
Back to top
View user's profile Send private message Send e-mail Visit poster's website Gallery Classifieds Feedback
raygreenwood
Samba Member


Joined: November 24, 2008
Posts: 21474
Location: Oklahoma City
raygreenwood is offline 

PostPosted: Sun Nov 26, 2017 7:45 pm    Post subject: Re: Restoring hardware, what is your chosen finish? Reply with quote

What the hardware is...and what it does....is what decides what coating it needs. If it needs to be zinc....you can electroplate at home with zinc for fairly cheap.

For most under the hood bolts and nuts....black phosphate with an oil pickle is just fine.

For items not likely to be chewed up....plates and connectors...distributor parts and door internal lataches... and need a harder surface and high rust proof.....use electroless nickle.

Electroless plating is superior in finish and accuracy to electro plating. There are some electroless zinc methods....but they are chemically complex. You can also do chemical galvanizing to get zinc without plating. Depends on what you need. Ray
Back to top
View user's profile Send private message Send e-mail Gallery Classifieds Feedback
Bob Loblaw
Samba Member


Joined: August 17, 2008
Posts: 865
Location: Vancouver Island, Canada
Bob Loblaw is offline 

PostPosted: Mon Nov 27, 2017 9:32 am    Post subject: Re: Restoring hardware, what is your chosen finish? Reply with quote

raygreenwood wrote:
black phosphate with an oil pickle is just fine.


I'm ignorant. I Googled "oil pickle", but that was no help.

Explain please?
_________________
sent from a phone using poor grammar and spelling
Back to top
View user's profile Send private message Gallery Classifieds Feedback
panicman
Samba Member


Joined: December 18, 2011
Posts: 2290
Location: Canby, OR
panicman is offline 

PostPosted: Mon Nov 27, 2017 10:07 am    Post subject: Re: Restoring hardware, what is your chosen finish? Reply with quote

You can put together a home zinc playing kit from almost scratch for about $25. I’ll hunt down my old thread with a good link.
_________________
Plate of shrimp
Back to top
View user's profile Send private message Gallery Classifieds Feedback
Tram
Samba Socialist


Joined: May 02, 2003
Posts: 22697
Location: Still Feelin' the Bern- Once you've felt it you can't un- feel it.
Tram is offline 

PostPosted: Mon Nov 27, 2017 10:43 am    Post subject: Re: Restoring hardware, what is your chosen finish? Reply with quote

vwtrey wrote:
Today, I have a pile of rusty bolts soaking in vinegar. Once these are cleaned, I will need a way to protect them. I don't care for painting bolts. I've never had results that I like. I considered getting an electroplating kit. What method do you prefer? Is there something that gives good results that I should try?


Get a bolt tumbler and media and let them rip for a few days. If you want to plate them they need to be spotless clean and no microscopic rust.

Yellow zinc was original for most all fasteners and hardware if you care about that. People don't realize that today because the yellow didn't last.
_________________
Немає виправдання для війни! Я з Україною.

Bryan67 wrote:
Just my hands. And a little lube. No tools.


To best contact me, please use the EMAIL function in my profile
Back to top
View user's profile Send private message Send e-mail Gallery Classifieds Feedback
hazetguy
Samba Member


Joined: April 06, 2001
Posts: 10773
Location: iT StiNgeD iTseLf tO dEAd
hazetguy is offline 

PostPosted: Mon Nov 27, 2017 11:50 am    Post subject: Re: Restoring hardware, what is your chosen finish? Reply with quote

for what the local industrial plater charges me to do huge batches, it is not even remotely worth my time or effort to do plating at home.

i almost always get the hardware that i use coated in black or clear (silver colored) zinc. have yet to run into any rust issues. in fact, i've had a piece sitting outside for about 4 years, as a test against the weather, and have yet to see a change. the clear (silver colored) zinc can be a bit brighter than i prefer for distributors, but i have yet to hear any complaints from customers about it.

phosphate leaves too rough a coating for my liking, and the plater did not recommend it for long term rust prevention. not sure what oil pickling is.

Tram, not sure when yellow zinc came into fashion, my guess is early 1970's as I have many early 60's NOS hardware, and it is definitely not yellow. i do have some NOS early 70's hardware and a lot of it is yellow. i also think it is cad plated, not zinc.
_________________
thebucket: I invested in hoodride, now DBD won't return my call?
hazetguy: invested?
thebucket: Yeah Haze, its where people put money into a company in hopes of a return on their money
Back to top
View user's profile Send private message Gallery Classifieds Feedback
Tram
Samba Socialist


Joined: May 02, 2003
Posts: 22697
Location: Still Feelin' the Bern- Once you've felt it you can't un- feel it.
Tram is offline 

PostPosted: Mon Nov 27, 2017 12:35 pm    Post subject: Re: Restoring hardware, what is your chosen finish? Reply with quote

hazetguy wrote:
for what the local industrial plater charges me to do huge batches, it is not even remotely worth my time or effort to do plating at home.

i almost always get the hardware that i use coated in black or clear (silver colored) zinc. have yet to run into any rust issues. in fact, i've had a piece sitting outside for about 4 years, as a test against the weather, and have yet to see a change. the clear (silver colored) zinc can be a bit brighter than i prefer for distributors, but i have yet to hear any complaints from customers about it.

phosphate leaves too rough a coating for my liking, and the plater did not recommend it for long term rust prevention. not sure what oil pickling is.

Tram, not sure when yellow zinc came into fashion, my guess is early 1970's as I have many early 60's NOS hardware, and it is definitely not yellow. i do have some NOS early 70's hardware and a lot of it is yellow. i also think it is cad plated, not zinc.


Yes, cad originally, but yellow zinc and Caswell's "Copy Cad" is indestinguishable from the original. I've had lots of early Type 3 hardware come through my hands and it's been yellow. since Type 3 began in 1961, I'd say it began in the early '60s at least. That's about the time it started appearing on Mercedes and Porsche hardware as well.
_________________
Немає виправдання для війни! Я з Україною.

Bryan67 wrote:
Just my hands. And a little lube. No tools.


To best contact me, please use the EMAIL function in my profile
Back to top
View user's profile Send private message Send e-mail Gallery Classifieds Feedback
turbotype1
Samba Member


Joined: April 30, 2005
Posts: 580
Location: seacoast
turbotype1 is offline 

PostPosted: Tue Nov 28, 2017 6:03 pm    Post subject: Re: Restoring hardware, what is your chosen finish? Reply with quote

Image may have been reduced in size. Click image to view fullscreen.


Caswell's "copy Cad"…. Bought their plating kit almost 20 years ago. Still going strong after all these years...
_________________
117harv wrote:
This new fad of get it the lowest, or run it with the worst looks, (patina) isn't cool, it's for the hey everyone look at me crowd, i'm driving a beat down ratty, unsafe, VW, how cool am I ???...your not....




Pissing off the purists since 1997

Wanted: Boyd Motors plate frame

57 Turbo Oval Sliding rag
67 13 window delux walk-thru- now 21
64 all original for the misses
83 Sinka m-TDI diesel
Back to top
View user's profile Send private message Gallery Classifieds Feedback
raygreenwood
Samba Member


Joined: November 24, 2008
Posts: 21474
Location: Oklahoma City
raygreenwood is offline 

PostPosted: Wed Nov 29, 2017 12:19 pm    Post subject: Re: Restoring hardware, what is your chosen finish? Reply with quote

hazetguy wrote:
for what the local industrial plater charges me to do huge batches, it is not even remotely worth my time or effort to do plating at home.

i almost always get the hardware that i use coated in black or clear (silver colored) zinc. have yet to run into any rust issues. in fact, i've had a piece sitting outside for about 4 years, as a test against the weather, and have yet to see a change. the clear (silver colored) zinc can be a bit brighter than i prefer for distributors, but i have yet to hear any complaints from customers about it.

phosphate leaves too rough a coating for my liking, and the plater did not recommend it for long term rust prevention. not sure what oil pickling is.

Tram, not sure when yellow zinc came into fashion, my guess is early 1970's as I have many early 60's NOS hardware, and it is definitely not yellow. i do have some NOS early 70's hardware and a lot of it is yellow. i also think it is cad plated, not zinc.


Oil pickling....is taking phosphated (and other types of conversion coatings)....which as you mention do not have long term rust resistance....and place them in a vat of oil or penetrating oil fluid...and bringing them up to a fairly high temperature. This opens the pores between the coating and metal and puts lubricant in them.

This makes them much more rust proof in semi-sheltered usage...like say under the dash or in the engine compartment.

Also..there are a great many sealer coatings (spray or dip) that black phosphate hardware can now use that make them virtually rustproof in semi-sheltered use....for many years.

Yellow zinc chromate came into fashion in the 1920's....pioneered by Ford.

There are a huge range of chromate colors...not just yellow. They range from bright blue, through pinkish, greenish, yellowish...and many non-chromate based coatings for zinc. None of the non-chromate based top coatings are yet as good as the original chrome based ones but they are getting there.

The chromate coatings are not there to be pretty...but because they can be at the same time...you get the range of colors available.

The use of a chromate top coat for zinc plating easily doubles its anti-corrosion lifespan.

The gist is this: Zinc....is just about THE BEST...SACRIFICIAL anti-rust coating for ferrous metal on the planet. The only thing that can actually beat it....is zinc-nickel plating.

The problem with zinc....is that in order for it to work as an anti-corrosion coating....the zinc itself MUST corrode. Even if the zinc plating is spotty...it still works because its an anode.

As zinc corrodes it produces what is termed in the plating industry as "white rust"...that powdery residue we see on non-chromated zinc plated parts ...for example...like the vacuum advance units on our distributors. With age they get that greyish white powdery residue. That is the zinc plating doing its job.

But...once this white rust/corrosion starts....it will never stop over numerous years until the zinc is depleted and then actual ferrous metal rust can start.

The chromate...originally containing hexavalent chrome...very toxic...was simply a dip sealant with the right anode/cathode mix to bond to the zinc. It prevented oxygen from getting to the zinc and starting the white rust process. The chromating process only takes seconds or minutes and is done after the zinc plating.....after the zinc parts have been rinsed and cleaned again....and then they have their surface tension changed again usually by a dip in something like tri-sodium phosphate..then a dip in the heated chromate solution...done. Sometimes they get baked afterwards to dry them completely.

Another type of "pickling" that is done on virtually all plated metals....is acid pickling....that is also sometimes called surface activation.

The object is to have a short dip in a SPECIFIC acid to get the surface reacting and ready to bond to whatever metal ion you are plating on it.

Its usually not a super concentrated acid...but that depends on the acid type.
There are acids that are oxidizing and acids that are non-oxidizing. It depends on the metal type. Sometimes the metal needs a lengthy time in an acid mix.....sometimes just a short dip.

If you go too long on some metals...it creates hydrogen embrittlement on the surface. This can cause porous plating that can allow oxygen through to rust.
Another example is too long of an acid pickle on cast iron exposes carbon and molybdenum in the surface pores which interfere in plating and cause porosity. Ray
Back to top
View user's profile Send private message Send e-mail Gallery Classifieds Feedback
shadyacres63
Samba Member


Joined: January 21, 2019
Posts: 7
Location: Temecula, CA
shadyacres63 is offline 

PostPosted: Wed Aug 07, 2019 2:52 pm    Post subject: Re: Restoring hardware, what is your chosen finish? Reply with quote

Has anyone used the Caswell black oxide kit? It has some pretty mixed reviews. I'm also trying to figure out if the cold black oxide process even comes close to the factory hot black oxide process in corrosion resistance. Any assistance/thoughts would be greatly appreciated!
_________________
1963 Beetle De Luxe Sedan Ragtop

Check out my restoration progress: https://63vwblog.blogspot.com/
Back to top
View user's profile Send private message Send e-mail Gallery Classifieds Feedback
Splitdog
Samba Split Personality


Joined: February 16, 2004
Posts: 4124
Location: Planet VW
Splitdog is offline 

PostPosted: Thu Aug 08, 2019 11:07 am    Post subject: Re: Restoring hardware, what is your chosen finish? Reply with quote

raygreenwood wrote:
hazetguy wrote:
for what the local industrial plater charges me to do huge batches, it is not even remotely worth my time or effort to do plating at home.

i almost always get the hardware that i use coated in black or clear (silver colored) zinc. have yet to run into any rust issues. in fact, i've had a piece sitting outside for about 4 years, as a test against the weather, and have yet to see a change. the clear (silver colored) zinc can be a bit brighter than i prefer for distributors, but i have yet to hear any complaints from customers about it.

phosphate leaves too rough a coating for my liking, and the plater did not recommend it for long term rust prevention. not sure what oil pickling is.

Tram, not sure when yellow zinc came into fashion, my guess is early 1970's as I have many early 60's NOS hardware, and it is definitely not yellow. i do have some NOS early 70's hardware and a lot of it is yellow. i also think it is cad plated, not zinc.


Oil pickling....is taking phosphated (and other types of conversion coatings)....which as you mention do not have long term rust resistance....and place them in a vat of oil or penetrating oil fluid...and bringing them up to a fairly high temperature. This opens the pores between the coating and metal and puts lubricant in them.

This makes them much more rust proof in semi-sheltered usage...like say under the dash or in the engine compartment.

Also..there are a great many sealer coatings (spray or dip) that black phosphate hardware can now use that make them virtually rustproof in semi-sheltered use....for many years.

Yellow zinc chromate came into fashion in the 1920's....pioneered by Ford.

There are a huge range of chromate colors...not just yellow. They range from bright blue, through pinkish, greenish, yellowish...and many non-chromate based coatings for zinc. None of the non-chromate based top coatings are yet as good as the original chrome based ones but they are getting there.

The chromate coatings are not there to be pretty...but because they can be at the same time...you get the range of colors available.

The use of a chromate top coat for zinc plating easily doubles its anti-corrosion lifespan.

The gist is this: Zinc....is just about THE BEST...SACRIFICIAL anti-rust coating for ferrous metal on the planet. The only thing that can actually beat it....is zinc-nickel plating.

The problem with zinc....is that in order for it to work as an anti-corrosion coating....the zinc itself MUST corrode. Even if the zinc plating is spotty...it still works because its an anode.

As zinc corrodes it produces what is termed in the plating industry as "white rust"...that powdery residue we see on non-chromated zinc plated parts ...for example...like the vacuum advance units on our distributors. With age they get that greyish white powdery residue. That is the zinc plating doing its job.

But...once this white rust/corrosion starts....it will never stop over numerous years until the zinc is depleted and then actual ferrous metal rust can start.

The chromate...originally containing hexavalent chrome...very toxic...was simply a dip sealant with the right anode/cathode mix to bond to the zinc. It prevented oxygen from getting to the zinc and starting the white rust process. The chromating process only takes seconds or minutes and is done after the zinc plating.....after the zinc parts have been rinsed and cleaned again....and then they have their surface tension changed again usually by a dip in something like tri-sodium phosphate..then a dip in the heated chromate solution...done. Sometimes they get baked afterwards to dry them completely.

Another type of "pickling" that is done on virtually all plated metals....is acid pickling....that is also sometimes called surface activation.

The object is to have a short dip in a SPECIFIC acid to get the surface reacting and ready to bond to whatever metal ion you are plating on it.

Its usually not a super concentrated acid...but that depends on the acid type.
There are acids that are oxidizing and acids that are non-oxidizing. It depends on the metal type. Sometimes the metal needs a lengthy time in an acid mix.....sometimes just a short dip.

If you go too long on some metals...it creates hydrogen embrittlement on the surface. This can cause porous plating that can allow oxygen through to rust.
Another example is too long of an acid pickle on cast iron exposes carbon and molybdenum in the surface pores which interfere in plating and cause porosity. Ray


Nice. Thanks!
_________________
CH³NO²

Z = z² + C

Der Blitzkrieg Kafers

#notacallooker
Back to top
View user's profile Send private message Send e-mail Gallery Classifieds Feedback
Elroyyy
Samba Member


Joined: November 09, 2004
Posts: 110
Location: Burbank, CA
Elroyyy is offline 

PostPosted: Thu Aug 08, 2019 11:28 am    Post subject: Re: Restoring hardware, what is your chosen finish? Reply with quote

Another option for a black coating is Birchwood Casey Super Blue. It's a combination of selenious acid, nitric acid and phosphoric acid and is intended for ferrous metals; it won't work on stainless steel or aluminum. Look it up on the googles.
_________________
My Classified Ads
Back to top
View user's profile Send private message Gallery Classifieds Feedback
shadyacres63
Samba Member


Joined: January 21, 2019
Posts: 7
Location: Temecula, CA
shadyacres63 is offline 

PostPosted: Thu Aug 08, 2019 8:18 pm    Post subject: Re: Restoring hardware, what is your chosen finish? Reply with quote

Elroyyy wrote:
Another option for a black coating is Birchwood Casey Super Blue. It's a combination of selenious acid, nitric acid and phosphoric acid and is intended for ferrous metals; it won't work on stainless steel or aluminum. Look it up on the googles.


That looks like the way to go, then a hot oil pickling to seal it. Thanks for the input.
_________________
1963 Beetle De Luxe Sedan Ragtop

Check out my restoration progress: https://63vwblog.blogspot.com/
Back to top
View user's profile Send private message Send e-mail Gallery Classifieds Feedback
Display posts from previous:   
Reply to topic    Forum Index -> General/Chat All times are Mountain Standard Time/Pacific Daylight Savings Time
Page 1 of 1

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum

About | Help! | Advertise | Donate | Premium Membership | Privacy/Terms of Use | Contact Us | Site Map
Copyright © 1996-2023, Everett Barnes. All Rights Reserved.
Not affiliated with or sponsored by Volkswagen of America | Forum powered by phpBB
Links to eBay or other vendor sites may be affiliate links where the site receives compensation.