Author |
Message |
OhHerrooo Samba Member
Joined: September 12, 2010 Posts: 1291 Location: Costa Mesa, CA
|
Posted: Thu Jan 18, 2018 4:36 pm Post subject: >67 trim on <66 fender |
|
|
I'm having a super tough time finding original paint, pearl white, passenger side body panels for my '67. I found an OG paint pass. rear fender in the classifieds but it is from a '66 (wider trim, bigger trim clip holes).
If I were to buy the fender from the '66 and put it on my '67... would the trim from my '67 be wide enough to cover the existing holes for the '66 trim clips? _________________ '67 Squareback
'69 Squareback
'68 Westfalia
'68 Squareback
OCT3 - Orange County Type 3's
www.evenkeelsurfshapes.com |
|
Back to top |
|
|
flyinglow94 Samba Member
Joined: January 17, 2005 Posts: 1166 Location: Las Vegas, Nevada
|
Posted: Thu Jan 18, 2018 5:17 pm Post subject: Re: >67 trim on <66 fender |
|
|
The holes for the 66 are the same size as your door card holes and take the same rubber boot to seal the hole. I don't think it will cover it and the clips are two different animals. _________________ "What we obtain too cheap, we esteem too lightly: 'tis dearness only that gives everything its value. Heaven knows how to put a proper price upon its goods; and it would be strange indeed if so celestial an article as FREEDOM should not be highly rated."
"Socialism is a philosophy of failure,the creed of ignorance, and the gospel of envy,its inherent virtue is the equal sharing of misery.." |
|
Back to top |
|
|
Bobnotch Samba Member
Joined: July 06, 2003 Posts: 22430 Location: Kimball, Mi
|
Posted: Fri Jan 19, 2018 11:42 am Post subject: Re: >67 trim on <66 fender |
|
|
OhHerrooo wrote: |
I'm having a super tough time finding original paint, pearl white, passenger side body panels for my '67. I found an OG paint pass. rear fender in the classifieds but it is from a '66 (wider trim, bigger trim clip holes).
If I were to buy the fender from the '66 and put it on my '67... would the trim from my '67 be wide enough to cover the existing holes for the '66 trim clips? |
I think it'll be close to covering. If you add the seals, then the seals will stick out at the edge of the trim. _________________ Bob 65 Notch S with Sunroof
71 Notch ...aka Krunchy; build pics here;
http://www.thesamba.com/vw/forum/viewtopic.php?t=249390 -been busy working
64 T-34 Ghia...aka Wolfie, under construction... http://www.thesamba.com/vw/forum/viewtopic.php?t=412120
Tram wrote: |
"Friends are God's way of apologizing for relatives." |
Tram wrote: |
People keep confusing "restored" and "restroyed". |
|
|
Back to top |
|
|
OhHerrooo Samba Member
Joined: September 12, 2010 Posts: 1291 Location: Costa Mesa, CA
|
Posted: Fri Jan 19, 2018 11:52 am Post subject: Re: >67 trim on <66 fender |
|
|
Bobnotch wrote: |
OhHerrooo wrote: |
I'm having a super tough time finding original paint, pearl white, passenger side body panels for my '67. I found an OG paint pass. rear fender in the classifieds but it is from a '66 (wider trim, bigger trim clip holes).
If I were to buy the fender from the '66 and put it on my '67... would the trim from my '67 be wide enough to cover the existing holes for the '66 trim clips? |
I think it'll be close to covering. If you add the seals, then the seals will stick out at the edge of the trim. |
I was just planning on drilling a new set of holes for the smaller trim clips and hoping the narrower trim would cover the existing holes. It'll probably be close. I'll compare my trim to some door trim clip plugs I have lying around. _________________ '67 Squareback
'69 Squareback
'68 Westfalia
'68 Squareback
OCT3 - Orange County Type 3's
www.evenkeelsurfshapes.com |
|
Back to top |
|
|
Bobnotch Samba Member
Joined: July 06, 2003 Posts: 22430 Location: Kimball, Mi
|
Posted: Fri Jan 19, 2018 11:58 am Post subject: Re: >67 trim on <66 fender |
|
|
OhHerrooo wrote: |
Bobnotch wrote: |
OhHerrooo wrote: |
I'm having a super tough time finding original paint, pearl white, passenger side body panels for my '67. I found an OG paint pass. rear fender in the classifieds but it is from a '66 (wider trim, bigger trim clip holes).
If I were to buy the fender from the '66 and put it on my '67... would the trim from my '67 be wide enough to cover the existing holes for the '66 trim clips? |
I think it'll be close to covering. If you add the seals, then the seals will stick out at the edge of the trim. |
I was just planning on drilling a new set of holes for the smaller trim clips and hoping the narrower trim would cover the existing holes. It'll probably be close. I'll compare my trim to some door trim clip plugs I have lying around. |
That's what I figured you were looking to do. _________________ Bob 65 Notch S with Sunroof
71 Notch ...aka Krunchy; build pics here;
http://www.thesamba.com/vw/forum/viewtopic.php?t=249390 -been busy working
64 T-34 Ghia...aka Wolfie, under construction... http://www.thesamba.com/vw/forum/viewtopic.php?t=412120
Tram wrote: |
"Friends are God's way of apologizing for relatives." |
Tram wrote: |
People keep confusing "restored" and "restroyed". |
|
|
Back to top |
|
|
Erik G Samba Member
Joined: October 16, 2002 Posts: 13281 Location: Tejas!
|
|
Back to top |
|
|
|