Author |
Message |
lawryr Samba Member
Joined: April 16, 2018 Posts: 6 Location: 32507
|
Posted: Mon Apr 16, 2018 4:56 pm Post subject: 69 panel distributor install |
|
|
my distributor line does not line up with the rotor
when at TDC on #1. also running terrible.
what to do?
|
|
Back to top |
|
|
busdaddy Samba Member
Joined: February 12, 2004 Posts: 51131 Location: Surrey B.C. Canada, but thinking of Ukraine
|
Posted: Mon Apr 16, 2018 5:36 pm Post subject: Re: 69 panel distributor install |
|
|
lawryr wrote: |
what to do? |
Explain how you are setting the timing, what distributor model you have and how you are determining #1 TDC to start with. _________________ Rust NEVER sleeps and stock never goes out of style.
Please don't PM technical questions, ask your problem in public so everyone can play along. If you think it's too stupid post it here
Stop dead photo links! Post your photos to The Samba Gallery!
Слава Україні! |
|
Back to top |
|
|
Wildthings Samba Member
Joined: March 13, 2005 Posts: 50338
|
Posted: Mon Apr 16, 2018 8:44 pm Post subject: Re: 69 panel distributor install |
|
|
If it is running at all then a couple of the plug wires have to be in the correct place, but two might be swapped. More info would help, is the engine back firing? When did the problem start? Is your compression good? Is the idle slow and weak?
Don't post the same question in different threads. |
|
Back to top |
|
|
lawryr Samba Member
Joined: April 16, 2018 Posts: 6 Location: 32507
|
Posted: Tue Apr 17, 2018 7:39 am Post subject: Re: 69 panel distributor install |
|
|
Thanks for the replies. TDC is with the flywheel mark aligned with the case split
and #1 valves closed while rocking the flywheel.
The engine is missing and will only start with timing retarded.
Engine is weak and tends to backfire.
I've been through the carb which is clean.
I think a cylinder is not firing due to the misaligned rotor and notch. |
|
Back to top |
|
|
EDragnDean Samba Member
Joined: July 13, 2005 Posts: 1148 Location: Vancouver, WA
|
|
Back to top |
|
|
Wildthings Samba Member
Joined: March 13, 2005 Posts: 50338
|
Posted: Tue Apr 17, 2018 9:06 am Post subject: Re: 69 panel distributor install |
|
|
lawryr wrote: |
Thanks for the replies. TDC is with the flywheel mark aligned with the case split
and #1 valves closed while rocking the flywheel.
The engine is missing and will only start with timing retarded.
Engine is weak and tends to backfire.
I've been through the carb which is clean.
I think a cylinder is not firing due to the misaligned rotor and notch. |
Check and double check your firing order one more time. If you have a couple of wires swapped your engine will fight to run and backfire when it does. |
|
Back to top |
|
|
lawryr Samba Member
Joined: April 16, 2018 Posts: 6 Location: 32507
|
Posted: Tue Apr 17, 2018 7:31 pm Post subject: Re: 69 panel distributor install |
|
|
checked the firing order twice. adjusted the valves and still have the same issues. ill check for intake and exhaust leaks. The carb is a new chinese PICT 1 which may be the issue. it's clean as a whistle but cheaply made.
ill change the plugs too since i'm not sure how old they are. |
|
Back to top |
|
|
busdaddy Samba Member
Joined: February 12, 2004 Posts: 51131 Location: Surrey B.C. Canada, but thinking of Ukraine
|
Posted: Tue Apr 17, 2018 8:01 pm Post subject: Re: 69 panel distributor install |
|
|
Is this a "new" Chinese distributor as well? _________________ Rust NEVER sleeps and stock never goes out of style.
Please don't PM technical questions, ask your problem in public so everyone can play along. If you think it's too stupid post it here
Stop dead photo links! Post your photos to The Samba Gallery!
Слава Україні! |
|
Back to top |
|
|
Wildthings Samba Member
Joined: March 13, 2005 Posts: 50338
|
Posted: Tue Apr 17, 2018 9:11 pm Post subject: Re: 69 panel distributor install |
|
|
You don't say where you live but getting someone familiar with one of these engines to take a look at yours might save you a lot of grief. There is likely a VW club somewhere not to far from you. |
|
Back to top |
|
|
lawryr Samba Member
Joined: April 16, 2018 Posts: 6 Location: 32507
|
Posted: Wed Apr 18, 2018 4:52 am Post subject: Re: 69 panel distributor install |
|
|
I'm in Pensacola FL. Rare Air is the local VW club here. |
|
Back to top |
|
|
busdaddy Samba Member
Joined: February 12, 2004 Posts: 51131 Location: Surrey B.C. Canada, but thinking of Ukraine
|
|
Back to top |
|
|
|