Hello! Log in or Register   |  Help  |  Donate  |  Buy Shirts See all banner ads | Advertise on TheSamba.com  
TheSamba.com
 
Advice on CR, before I order heads
Forum Index -> Performance/Engines/Transmissions Share: Facebook Twitter
Reply to topic
Print View
Quick sort: Show newest posts on top | Show oldest posts on top View previous topic :: View next topic  
Author Message
msaltz
Samba Member


Joined: October 24, 2015
Posts: 42
Location: Fallbrook
msaltz is offline 

PostPosted: Sat Aug 11, 2018 6:58 pm    Post subject: Advice on CR, before I order heads Reply with quote

Before I order my heads I want to make sure I am going to be running the proper compression ratio (CR). My initial plan was to run a 9.5:1 CR, but it was mentioned to me that may be to high for the below spec engine? I would like to know what experienced people think and make sure I'm not making any major mistakes. I know this is somewhat subjective but I would like to get some opinions. The engine is going in a 65 ghia that will be somewhat of a daily driver. I have decided on Steve Tim's stage II heads and they can do up to a 60cc chamber.

Engine:

2180cc (92 thick wall pistons/ 82mm crank)

Deck Height- #1=0.0405", #2=0.0435", #3=0.0395", #4=0.0420", These are with a 0.09" shim under the cylinder.

SCAT pro series 1.25:1 rockers;

Dual 44HPMX carbs;

1 5/8" exhaust (I think);

Web 163 cam:
Intake Exhaust
Valve Lash (Inch): .006" .006"
Valve Lift (Inch): 0.430 0.430
Valve Lift (mm): 10.92 10.92
Advertised Duration: 288° 288°
Duration @ 0.050": 250° 250°
Lobe Center: 108° 108°

Not necessarily looking every last drop of HP that I can get with this set up but would like the car to be fun, smooth running and idle well. Any opinions would be greatly appreciated, especially any objections to the 9.5:1 CR!

Thanks,
Back to top
View user's profile Send private message Gallery Classifieds Feedback
Cptn. Calzone
Samba Member


Joined: June 27, 2007
Posts: 1855
Location: S>E>Alabama
Cptn. Calzone is offline 

PostPosted: Sat Aug 11, 2018 9:30 pm    Post subject: Re: Advice on CR, before I order heads Reply with quote

I currently run that cam with Timms stage 1.5 heads.Cool and strong.Make certain of lifter compatability. Comp is 8.5.1 in a 67SC truck.Pulls really well and quiet valve train.Guy that built it did an outstanding job.
_________________
71 westfalia
67 912 Porsche Quintilla
67 Single Cab aka my work horse
Back to top
View user's profile Send private message Send e-mail Gallery Classifieds Feedback
74 Thing
Samba Member


Joined: September 02, 2004
Posts: 7529

74 Thing is offline 

PostPosted: Sun Aug 12, 2018 12:30 am    Post subject: Re: Advice on CR, before I order heads Reply with quote

I would leave it as it is or change the cam to WebCam 86b with 1.4 CB or Scat rockers.

Tune it good and run good octane gas

https://vwparts.aircooled.net/Web-Cam-Type-1-Camshaft-Grind-163-1-1-or-1-25-p/00-212.htm
Back to top
View user's profile Send private message Gallery Classifieds Feedback
Alstrup
Samba Member


Joined: July 12, 2007
Posts: 7451
Location: Videbaek Denmark
Alstrup is offline 

PostPosted: Sun Aug 12, 2018 1:13 am    Post subject: Re: Advice on CR, before I order heads Reply with quote

msaltz wrote:
Before I order my heads I want to make sure I am going to be running the proper compression ratio (CR). My initial plan was to run a 9.5:1 CR, but it was mentioned to me that may be to high for the below spec engine? I would like to know what experienced people think and make sure I'm not making any major mistakes. I know this is somewhat subjective but I would like to get some opinions. The engine is going in a 65 ghia that will be somewhat of a daily driver. I have decided on Steve Tim's stage II heads and they can do up to a 60cc chamber.

Engine:

2180cc (92 thick wall pistons/ 82mm crank)

Deck Height- #1=0.0405", #2=0.0435", #3=0.0395", #4=0.0420", These are with a 0.09" shim under the cylinder.

SCAT pro series 1.25:1 rockers;

Dual 44HPMX carbs;

1 5/8" exhaust (I think);

Web 163 cam:
Intake Exhaust
Valve Lash (Inch): .006" .006"
Valve Lift (Inch): 0.430 0.430
Valve Lift (mm): 10.92 10.92
Advertised Duration: 288° 288°
Duration @ 0.050": 250° 250°
Lobe Center: 108° 108°

Not necessarily looking every last drop of HP that I can get with this set up but would like the car to be fun, smooth running and idle well. Any opinions would be greatly appreciated, especially any objections to the 9.5:1 CR!

Thanks,

9,5 is ok, - on premium fuel. That said I tend to agree on the 86B cam. Then you can go 1 notch down in fuel octane too.
T
Back to top
View user's profile Send private message Send e-mail Gallery Classifieds Feedback
mark tucker
Samba Member


Joined: April 08, 2009
Posts: 23946
Location: SHALIMAR ,FLORIDA
mark tucker is offline 

PostPosted: Sun Aug 12, 2018 10:31 am    Post subject: Re: Advice on CR, before I order heads Reply with quote

ditto,to alstrup, I didnt care for the 163....but it wasent mine somebody else was paying for it so thats what went in.
Back to top
View user's profile Send private message Gallery Classifieds Feedback
bugguy1967
Samba Member


Joined: January 16, 2008
Posts: 4354
Location: Los Angeles, CA 90016
bugguy1967 is offline 

PostPosted: Sun Aug 12, 2018 10:49 am    Post subject: Re: Advice on CR, before I order heads Reply with quote

It's looks milder than a W120, and 9.5:1 is generally the limit for that cam. If you do run 9.5, you need to be pretty knowledgable about AFR and ignition timing. 9.0:1 is safer.

The Stage 2s are kind of big for your cam. They flow about 180 CFM@25"/.550". You'd be better off with the Stage 1s. Or even better, CNC chamber Panchitos.
_________________
"A petrol engine can start readily, run smoothly and give every appearance of being in good order, without necessarily being in good tune." - Colin Campbell, "The Sportscar Engine"
Back to top
View user's profile Send private message Send e-mail Gallery Classifieds Feedback
msaltz
Samba Member


Joined: October 24, 2015
Posts: 42
Location: Fallbrook
msaltz is offline 

PostPosted: Sun Aug 12, 2018 3:38 pm    Post subject: Re: Advice on CR, before I order heads Reply with quote

Thanks for all the input. I am leaning towards going with the Tim's Stage II heads w/60 cc chambers. With my not very consistent deck heights that should put me about 9.1-9.2:1 CR. I'll role with that and see how it performs.


Thanks again.
Back to top
View user's profile Send private message Gallery Classifieds Feedback
mcmscott
Samba Member


Joined: March 12, 2010
Posts: 4888
Location: sanger ca
mcmscott is offline 

PostPosted: Sun Aug 12, 2018 6:05 pm    Post subject: Re: Advice on CR, before I order heads Reply with quote

msaltz wrote:
Before I order my heads I want to make sure I am going to be running the proper compression ratio (CR). My initial plan was to run a 9.5:1 CR, but it was mentioned to me that may be to high for the below spec engine? I would like to know what experienced people think and make sure I'm not making any major mistakes. I know this is somewhat subjective but I would like to get some opinions. The engine is going in a 65 ghia that will be somewhat of a daily driver. I have decided on Steve Tim's stage II heads and they can do up to a 60cc chamber.

Engine:

2180cc (92 thick wall pistons/ 82mm crank)

Deck Height- #1=0.0405", #2=0.0435", #3=0.0395", #4=0.0420", These are with a 0.09" shim under the cylinder.

SCAT pro series 1.25:1 rockers;

Dual 44HPMX carbs;

1 5/8" exhaust (I think);

Web 163 cam:
Intake Exhaust
Valve Lash (Inch): .006" .006"
Valve Lift (Inch): 0.430 0.430
Valve Lift (mm): 10.92 10.92
Advertised Duration: 288° 288°
Duration @ 0.050": 250° 250°
Lobe Center: 108° 108°

Not necessarily looking every last drop of HP that I can get with this set up but would like the car to be fun, smooth running and idle well. Any opinions would be greatly appreciated, especially any objections to the 9.5:1 CR!

Thanks,




Your deck is all over the place! fix that first! then ask questions
_________________
There are no stupid questions, only stupid people,

68 Ghia
67 T-1
65 Notch
02 Mexican beetle
74 Thing
15 Long travel rail
07 Nomad
05 f-250
Back to top
View user's profile Send private message Gallery Classifieds Feedback
mark tucker
Samba Member


Joined: April 08, 2009
Posts: 23946
Location: SHALIMAR ,FLORIDA
mark tucker is offline 

PostPosted: Mon Aug 13, 2018 10:36 am    Post subject: Re: Advice on CR, before I order heads Reply with quote

I figuyred he wasent all that carfull checking the deck hight....or in the right /same position on each setup...I would also suggest the lost pan of cheetos cb heads for this build.CNC of course.

Last edited by mark tucker on Tue Aug 14, 2018 8:34 am; edited 1 time in total
Back to top
View user's profile Send private message Gallery Classifieds Feedback
74 Thing
Samba Member


Joined: September 02, 2004
Posts: 7529

74 Thing is offline 

PostPosted: Mon Aug 13, 2018 8:57 pm    Post subject: Re: Advice on CR, before I order heads Reply with quote

Why don't you ask Tims what to run and have him set up the heads for the compression you want? They know their stuff.
Back to top
View user's profile Send private message Gallery Classifieds Feedback
Display posts from previous:   
Reply to topic    Forum Index -> Performance/Engines/Transmissions All times are Mountain Standard Time/Pacific Daylight Savings Time
Page 1 of 1

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum

About | Help! | Advertise | Donate | Premium Membership | Privacy/Terms of Use | Contact Us | Site Map
Copyright © 1996-2024, Everett Barnes. All Rights Reserved.
Not affiliated with or sponsored by Volkswagen of America | Forum powered by phpBB
Links to eBay or other vendor sites may be affiliate links where the site receives compensation.