Hello! Log in or Register   |  Help  |  Donate  |  Buy Shirts See all banner ads | Advertise on TheSamba.com  
TheSamba.com
 
Filter bracket mount area for full flow on a Thing
Forum Index -> Thing/Type 181 Share: Facebook Twitter
Reply to topic
Print View
Quick sort: Show newest posts on top | Show oldest posts on top View previous topic :: View next topic  
Author Message
74 Thing
Samba Member


Joined: September 02, 2004
Posts: 7390

74 Thing is offline 

PostPosted: Wed Oct 17, 2018 9:15 am    Post subject: Filter bracket mount area for full flow on a Thing Reply with quote

I was looking for photos and ideas for full flow filter bracket mounting areas on a Thing. Currently mine is off the bumper bracket since it is a straight shot to the case, but I may have to move it and was looking for suggestions.
Back to top
View user's profile Send private message Gallery Classifieds Feedback
Glenn Premium Member
Mr. 010


Joined: December 25, 2001
Posts: 76909
Location: Sneaking up behind you
Glenn is offline 

PostPosted: Wed Oct 17, 2018 9:21 am    Post subject: Re: Filter bracket mount area for full flow on a Thing Reply with quote

Just mount it in the left rear fender well.
_________________
Glenn
74 Beetle Specs | 74 Beetle Restoration | 2180cc Engine
"You may not get what you pay for, but you always pay for what you get"

Member #1009

#BlueSquare
Back to top
View user's profile Send private message Send e-mail Visit poster's website Gallery Classifieds Feedback
74 Thing
Samba Member


Joined: September 02, 2004
Posts: 7390

74 Thing is offline 

PostPosted: Wed Oct 17, 2018 9:31 am    Post subject: Re: Filter bracket mount area for full flow on a Thing Reply with quote

I am avoiding the fender well. I blew out the rear drivers side tire on the highway before and the tire wrapped around the drum and it tore off the oil filter and lines. Needless to say being stuck in the fast lane on the small shoulder of the freeway with a blown tire and an oil down with no hose to repair is not fun or safe.
Back to top
View user's profile Send private message Gallery Classifieds Feedback
mondshine
Samba Member


Joined: October 27, 2006
Posts: 2769
Location: The World's Motor Capital
mondshine is offline 

PostPosted: Wed Oct 17, 2018 10:44 am    Post subject: Re: Filter bracket mount area for full flow on a Thing Reply with quote

Here's an ancient "Mecca" oil filter, mounted on the driver's side air filter mount.
It's well over 30 years old. Now-a-days, they're called Canton Mecca, and they look a little different (the body is an aluminum extrusion, rather than a casting), but they use the same filter elements as always (probably the same as the spin on filter under Glenn's fender).

Image may have been reduced in size. Click image to view fullscreen.



There's lots of extra, unrecognizable stuff in the picture, but the filter inlet is at the bottom. The filter outlet, barely visible in this picture, is connected to an oil thermostat attached to the "firewall" with bulkhead fittings. The hose with the "T" fitting is the return hose to the engine.

Here's a sketch of the overall layout:
Image may have been reduced in size. Click image to view fullscreen.



Just for another idea. here’s the installation I did in a ’71 Super Beetle in 2006.
The Beetle engine compartment is far less roomy than a Thing’s, and this was a very compact installation.
This is the later style Canton Mecca cartridge filter (the shorter model).
It was mounted directly on the engine, using only hard lines (no hoses at all).
Image may have been reduced in size. Click image to view fullscreen.

Image may have been reduced in size. Click image to view fullscreen.

In this installation, a low crack pressure check valve (Moroso 23875) was mounted at the filter inlet as an anti-drain-back device.

Both of these arrangements stay nice and clean, and are very easy to service.
Good luck, Mondshine
Back to top
View user's profile Send private message AIM Address Gallery Classifieds Feedback
Display posts from previous:   
Reply to topic    Forum Index -> Thing/Type 181 All times are Mountain Standard Time/Pacific Daylight Savings Time
Page 1 of 1

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum

About | Help! | Advertise | Donate | Premium Membership | Privacy/Terms of Use | Contact Us | Site Map
Copyright © 1996-2023, Everett Barnes. All Rights Reserved.
Not affiliated with or sponsored by Volkswagen of America | Forum powered by phpBB
Links to eBay or other vendor sites may be affiliate links where the site receives compensation.