Author |
Message |
deluxe hunter Samba Member
Joined: May 17, 2007 Posts: 42
|
Posted: Wed Jan 16, 2019 1:29 am Post subject: Help Needed 741 trans into an A |
|
|
Im looking for advice and information on fitting a 741 trans into a 57 A.
What needs changing and or modifying? (on the car or the trans)
Engine will be from a 912.
thanks in advance |
|
Back to top |
|
|
ensys Samba Member
Joined: March 11, 2009 Posts: 322 Location: America's Automobile Heartland
|
Posted: Wed Jan 16, 2019 10:18 pm Post subject: Re: Help Needed 741 trans into an A |
|
|
Mr.hunter:
The lump itself lofts right in without modifications.
The three issues of concern are:
- getting the T.O.brng/press.plate/flywheel combo right.
- getting the correct (longer) cable/end hardware.
- getting the correct throttle cable/case pivot/pull rod combination.
At least, these were the issues I found in installing a 741 in my T1 (along with disk brakes) back in the 80s.
Have fun. _________________ Keep 'em flying...
S.J.Szabo |
|
Back to top |
|
|
deluxe hunter Samba Member
Joined: May 17, 2007 Posts: 42
|
Posted: Thu Jan 17, 2019 5:09 pm Post subject: Re: Help Needed 741 trans into an A |
|
|
Thanks
So will the 741 nosecone/hockey stick etc will all work and line up with the T1 shift rod etc??
cheers |
|
Back to top |
|
|
Jacks Samba Member
Joined: July 15, 2006 Posts: 2347 Location: San Clemente, Ca.
|
Posted: Fri Jan 18, 2019 2:58 am Post subject: Re: Help Needed 741 trans into an A |
|
|
No _________________ Jack Staggs
Actual name |
|
Back to top |
|
|
deluxe hunter Samba Member
Joined: May 17, 2007 Posts: 42
|
Posted: Tue Jan 22, 2019 12:47 am Post subject: Re: Help Needed 741 trans into an A |
|
|
I am looking for guidance here to fit the 741 into the T1.
'Jacks' has said the 741 gear selector is not in the correct place for me...so can I simply swap the nosecone/hockey stick from my 644 to the 741 ??
or what else is required??
thanks |
|
Back to top |
|
|
donco735 Samba Member
Joined: December 13, 2018 Posts: 38 Location: New Mexico
|
Posted: Tue Jan 29, 2019 8:22 pm Post subject: Re: Help Needed 741 trans into an A |
|
|
Check 356 Registery, Volume 3, No. 3. Lemme know if you don't have access to it and I'll post the article |
|
Back to top |
|
|
Jacks Samba Member
Joined: July 15, 2006 Posts: 2347 Location: San Clemente, Ca.
|
Posted: Fri Feb 01, 2019 1:27 am Post subject: Re: Help Needed 741 trans into an A |
|
|
You have to change the shift fork operating shafts too _________________ Jack Staggs
Actual name |
|
Back to top |
|
|
deluxe hunter Samba Member
Joined: May 17, 2007 Posts: 42
|
Posted: Fri Feb 01, 2019 9:05 pm Post subject: Re: Help Needed 741 trans into an A |
|
|
thanks donco,
Im not a member on the registry, so if you could post the article here it would be appreciated.
cheers |
|
Back to top |
|
|
ensys Samba Member
Joined: March 11, 2009 Posts: 322 Location: America's Automobile Heartland
|
Posted: Fri Feb 01, 2019 10:40 pm Post subject: Re: Help Needed 741 trans into an A |
|
|
Mr.Staggs:
My thanks for correcting my grievous oversight. The old synapses were not firing well, I reckon.
Please fact-check me if I offer that all the needed nose/shift parts can be cannibalized from a 644 box, if need requires _________________ Keep 'em flying...
S.J.Szabo |
|
Back to top |
|
|
donco735 Samba Member
Joined: December 13, 2018 Posts: 38 Location: New Mexico
|
Posted: Sat Feb 02, 2019 11:39 am Post subject: Re: Help Needed 741 trans into an A |
|
|
deluxe hunter wrote: |
thanks donco,
Im not a member on the registry, so if you could post the article here it would be appreciated.
cheers |
|
|
Back to top |
|
|
deluxe hunter Samba Member
Joined: May 17, 2007 Posts: 42
|
Posted: Tue Feb 05, 2019 4:24 pm Post subject: Re: Help Needed 741 trans into an A |
|
|
thank you.....perfect |
|
Back to top |
|
|
PD41 Samba Member
Joined: May 30, 2016 Posts: 109 Location: Redondo Beach
|
Posted: Tue Feb 05, 2019 11:11 pm Post subject: Re: Help Needed 741 trans into an A |
|
|
Great info Donco. |
|
Back to top |
|
|
|