Author |
Message |
EastyRider Samba Member
Joined: March 25, 2019 Posts: 11 Location: NC
|
Posted: Mon Mar 25, 2019 2:08 pm Post subject: Driver side window stuck all the way down |
|
|
I looked all over the forum but couldn't find a solution to my problem. Maybe you fine folks can help...
I have a 1991 Vanagon Multivan with power windows. The other day, I rolled the driver side window down all the way to enjoy the beautiful Spring air in NC. When I got home, I tried to roll the window up and nothing happened...
I took off the door panel to inspect (keep in mind, the window is all the way down). I swapped around the switches to see if the switch was the problem. The driver side switch worked on the passenger window, so I ruled that out. The switch illuminates, so it is getting power.
I tried to move the door open and closed to see if it was a wire break in the crease, but nothing happened.
Next, I put my ear next to the motor/regulator and pressed the switch. I could hear a low electrical surge sound but nothing else... No clicking or anything
Is the motor jammed or the regulator or both? I am unable to remove them to inspect due to the window being all the way down AKA no access to the necessary 10mm bolts to release the regulator...
If it is one of those, how the hell do I get them out now that the window is all the way down? I saw someone was able to do it by cutting a hole in the door to access the bolts. is there another way?
FYI, water had been in the door due to a poor seal at the scraper before I bought it... |
|
Back to top |
|
|
0to60in6min Samba Member
Joined: November 27, 2006 Posts: 3416 Location: OR & CA (Oregon/California)
|
|
Back to top |
|
|
MarkWard Samba Member
Joined: February 09, 2005 Posts: 17118 Location: Retired South Florida
|
Posted: Mon Mar 25, 2019 2:27 pm Post subject: Re: Driver side window stuck all the way down |
|
|
The actual motor has 2 wires. Power and ground. Sort of. The switch reverses them. So you could test the motor with an external power supply. Another option is to tap the motor while you work the switch to raise the window. That sometimes works.
I would refrain from cutting holes in the door. You might be able to undo the regulator and move it around enough to unbolt the glass from the lift mech _________________ ☮️ |
|
Back to top |
|
|
DuncanS Samba Member
Joined: October 17, 2013 Posts: 4583 Location: New Hampshire
|
Posted: Mon Mar 25, 2019 6:07 pm Post subject: Re: Driver side window stuck all the way down |
|
|
Do this:
Unfortunately, I don't have any measurements, but if you scale them off the photos, you can get the location of the holes. I think I remember the back hole 1 1/2" back from the hole for the panel retainer and the distance between the two at 5". But I could be wrong as it was several years ago so try to verify by scaling from the photo. They don't have to be exact and it you miss a bit, just enlarge them as the panel covers it all anyway.
In this top photo you can see the bolt head through the hole.
In the second photo, you can see how I put a magnet on the socket extension so the bolts wouldn't disappear into the door. Once the bolts are out, you can raise the window manually and then deal with the issues.
If the motor--electric? won't work, then you have hold the window up while you remove the regulator. If is wiring then that's another issue recently dealt with in the topic "Power window driver side wiring". (Can someone tell be how to get the topic in blue as a link?) If you have to remove the glass, then remove all the weather stripping, the vent window and take the glass out. |
|
Back to top |
|
|
EastyRider Samba Member
Joined: March 25, 2019 Posts: 11 Location: NC
|
Posted: Mon Mar 25, 2019 6:12 pm Post subject: Re: Driver side window stuck all the way down |
|
|
MarkWard wrote: |
The actual motor has 2 wires. Power and ground. Sort of. The switch reverses them. So you could test the motor with an external power supply. Another option is to tap the motor while you work the switch to raise the window. That sometimes works.
I would refrain from cutting holes in the door. You might be able to undo the regulator and move it around enough to unbolt the glass from the lift mech |
How exactly do you test the motor? |
|
Back to top |
|
|
EastyRider Samba Member
Joined: March 25, 2019 Posts: 11 Location: NC
|
Posted: Mon Mar 25, 2019 6:17 pm Post subject: Re: Driver side window stuck all the way down |
|
|
DuncanS wrote: |
Do this:
Unfortunately, I don't have any measurements, but if you scale them off the photos, you can get the location of the holes. I think I remember the back hole 1 1/2" back from the hole for the panel retainer and the distance between the two at 5". But I could be wrong as it was several years ago so try to verify by scaling from the photo. They don't have to be exact and it you miss a bit, just enlarge them as the panel covers it all anyway.
In this top photo you can see the bolt head through the hole.
In the second photo, you can see how I put a magnet on the socket extension so the bolts wouldn't disappear into the door. Once the bolts are out, you can raise the window manually and then deal with the issues.
If the motor--electric? won't work, then you have hold the window up while you remove the regulator. If is wiring then that's another issue recently dealt with in the topic "Power window driver side wiring". (Can someone tell be how to get the topic in blue as a link?) If you have to remove the glass, then remove all the weather stripping, the vent window and take the glass out. |
Thanks for the info Duncan. I saw these photos in another post... Is there no other way?? I don't want to make holes, but I will if I have to. I saw another post where they had to cut the cable to the regulator but I am trying to avoid that also in case it doesn't need replacing.
Last edited by EastyRider on Fri Mar 29, 2019 8:41 am; edited 1 time in total |
|
Back to top |
|
|
Paulbeard Samba Member
Joined: July 10, 2015 Posts: 2604 Location: Seattle
|
Posted: Mon Mar 25, 2019 6:18 pm Post subject: Re: Driver side window stuck all the way down |
|
|
EastyRider wrote: |
How exactly do you test the motor? |
Hook up the wires to battery +/- Jumper cables would work in a pinch. The battery's not far. You can find a good ground at the seatbelt bolt or the screws that hold the door latch to the jamb. _________________ Currently -> Frida: 87 Tizian Red (mostly) Vanagon GL Westfalia w/ 2.0L ABA conversion
Formerly -> Steward of a 73 Super Beetle (Beater) and 67 Beetle 1300 (Little Max) both names by POs
— dhaavers |
|
Back to top |
|
|
CurtisS Samba Member
Joined: March 01, 2006 Posts: 128 Location: Kingston, WA USA
|
Posted: Tue Mar 26, 2019 12:35 pm Post subject: Re: Driver side window stuck all the way down |
|
|
It is likely the funky cable that raises/lowers the window has broken inside the gearbox connected to the motor and jammed it all up. It is not much fun to get out but I never had to drill holes in my door! See if you can get the window loose from the raising mechanism and follow the Bentley for removing the whole power window assembly (motor, gearbox and cable tubes). _________________ If "con" is the opposite of "pro", what is the opposite of "progress"? |
|
Back to top |
|
|
DuncanS Samba Member
Joined: October 17, 2013 Posts: 4583 Location: New Hampshire
|
Posted: Tue Mar 26, 2019 12:59 pm Post subject: Re: Driver side window stuck all the way down |
|
|
DO NOT CUT THE CABLE. Holes get covered. No sign of them afterwards. There IS no other way to get either the glass or regulator/motor out. |
|
Back to top |
|
|
EastyRider Samba Member
Joined: March 25, 2019 Posts: 11 Location: NC
|
Posted: Tue Mar 26, 2019 7:07 pm Post subject: Re: Driver side window stuck all the way down |
|
|
DuncanS wrote: |
DO NOT CUT THE CABLE. Holes get covered. No sign of them afterwards. There IS no other way to get either the glass or regulator/motor out. |
Thanks Duncan! If I can't get the regulator loose somehow, I will have to use a hole saw or drill bit to get a clean hole to access the bolts. |
|
Back to top |
|
|
DuncanS Samba Member
Joined: October 17, 2013 Posts: 4583 Location: New Hampshire
|
Posted: Tue Mar 26, 2019 7:15 pm Post subject: Re: Driver side window stuck all the way down |
|
|
The regulator is bolted to the glass with those two bolts. It is NOT possible to remove the regulator without removing the two bolts. |
|
Back to top |
|
|
CurtisS Samba Member
Joined: March 01, 2006 Posts: 128 Location: Kingston, WA USA
|
Posted: Wed Mar 27, 2019 9:07 am Post subject: Re: Driver side window stuck all the way down |
|
|
Can you physically move the window up by hand from the inside? If yes you should be able to get it into a position where you can access the bolts. _________________ If "con" is the opposite of "pro", what is the opposite of "progress"? |
|
Back to top |
|
|
EastyRider Samba Member
Joined: March 25, 2019 Posts: 11 Location: NC
|
Posted: Wed Mar 27, 2019 2:13 pm Post subject: Re: Driver side window stuck all the way down |
|
|
After beating on the motor/regulator with the grip end of a pair of channel locks, locking in the up button, and pulling up on the bottom of the glass.. I was able to get the motor to spin a little bit at a time until it was finally in position to where I can get to bolts out!!! Uhhh what now??? Haha |
|
Back to top |
|
|
MarkWard Samba Member
Joined: February 09, 2005 Posts: 17118 Location: Retired South Florida
|
Posted: Wed Mar 27, 2019 2:47 pm Post subject: Re: Driver side window stuck all the way down |
|
|
Congrats, glad you did not have to molest the door to do it. We have a member that rebuilds them. 16cvs or something similar is the user name. I would use him. No affiliation. _________________ ☮️ |
|
Back to top |
|
|
DuncanS Samba Member
Joined: October 17, 2013 Posts: 4583 Location: New Hampshire
|
Posted: Wed Mar 27, 2019 5:03 pm Post subject: Re: Driver side window stuck all the way down |
|
|
Pull the bolts, pull the regulator. Try it one more time going directly from the battery to the motor. Just small test shots. If stiff, pull the motor. Once the motor is free of the regulator check it again to determine if it's the motor or the cable assembly. Check out the motor rebuild threads. Not as tough as it is made out to be. |
|
Back to top |
|
|
EastyRider Samba Member
Joined: March 25, 2019 Posts: 11 Location: NC
|
Posted: Wed Mar 27, 2019 8:13 pm Post subject: Re: Driver side window stuck all the way down |
|
|
Pulled the motor and it was gunked up and full of water. Tested it after draining and it turned briefly but I could tell it needed to be cleaned. Disassembled. Bearings were stuck to the shaft. Was able to break those loose and clean everything up pretty well. Just need to get some electric motor grease tomorrow befor reassembling it. Fingers crossed this is the issue |
|
Back to top |
|
|
VicVan Samba Member
Joined: July 01, 2015 Posts: 1840 Location: Vancouver Island, BC
|
Posted: Wed Mar 27, 2019 10:54 pm Post subject: Re: Driver side window stuck all the way down |
|
|
As recommended somewhere on this forum, I drilled a small hole at the bottom the regulators last time I did this job. It will allow the water to drain out, and if you place it smartly, will allow you to spray grease in there once in a while. _________________ '90 Little Blue Truck, 2WD auto, FAS GenV 2.0 NA (AVH) |
|
Back to top |
|
|
JSlate Samba Member
Joined: March 22, 2015 Posts: 15 Location: Florida
|
Posted: Thu Mar 28, 2019 5:26 am Post subject: Re: Driver side window stuck all the way down |
|
|
Let me know how the motor does after you re-assemble. I've been working on the same issue. At first I thought it was the wiring, now I'm suspecting the motor, but still the wiring is a possibility. I'll likely be pulling the motor out and cleaning it up just like you did.
https://www.thesamba.com/vw/forum/viewtopic.php?t=715758&highlight= |
|
Back to top |
|
|
EastyRider Samba Member
Joined: March 25, 2019 Posts: 11 Location: NC
|
Posted: Fri Mar 29, 2019 7:34 am Post subject: Re: Driver side window stuck all the way down |
|
|
In my situation, the water and gunk in the motor housing was restricting the motor from spinning. After taking it apart, thoroughly cleaning everything, breaking free the bearings, polishing the shaft/bearings, and lubing it all up with motor oil.... it now spins!
It was all caused by water entering the door through a poor seal at the scraper. I will install the motor and regulator this evening and report back once it is all in place.
|
|
Back to top |
|
|
16CVs Samba Member
Joined: February 22, 2004 Posts: 4024 Location: Redwood City, California
|
Posted: Fri Mar 29, 2019 8:32 am Post subject: Re: Driver side window stuck all the way down |
|
|
It has nothing to do with the outside window scraper ! Those are not designed to keep water out. A properly sealed door skin is what protects the door panel from moisture and dirt intrusion. The door has drain holes in the bottom that need to be clear and open. The scraper keeps the big leaves and crap from entering the door and cover the metal at the top. Nothing more.
You need to stake that bearing keeper at the bottom. The bearing needs to held fast and not free spinning.
Drilling a hole in the regulator is not needed, take out the 2 rubber plugs in the bottom of the motor and that will allow any water that enters the motors to exit.
I have rebuilt 532 Motors and 320 Regulators, I may have seen a thing or 2 on the path down the road.
Stacy _________________ 1987 Syncro Westfalia Triple knob (bastard)
1989 Syncro Tristar Triple knob "Swedish"
2013 Jetta Hybrid a true "Zwitter"
Samba member # 14980
Call anytime number 650 722 4914 .
Keep Your van running and upkept tastefully for the love of the hobby.
Don't let your van end up in an "abortions" thread. |
|
Back to top |
|
|
|