Hello! Log in or Register   |  Help  |  Donate  |  Buy Shirts  See all banner ads | Advertise on TheSamba.com  
TheSamba.com
 
Let the process of saving 2222069996 begin
Page: Previous  1, 2, 3, 4, 5, 6, 7
Forum Index -> Bay Window Bus Share: Facebook Twitter
Reply to topic
Print View
Quick sort: Show newest posts on top | Show oldest posts on top View previous topic :: View next topic  
Author Message
malcolm2
Samba Member


Joined: September 28, 2011
Posts: 727
Location: Mount Juliet, TN
malcolm2 is offline 

PostPosted: Mon Jun 08, 2020 2:19 pm    Post subject: Re: Let the process of saving 2222069996 begin Reply with quote

Image may have been reduced in size. Click image to view fullscreen.


cam thrust bearing came with a tang.... but does not need it. I ground it off. As you can see the upper portion of the picture is the saddle where the bearing goes and the bearing below with the tang.... NO NOTCH.

old removed, dark bearing next to the new one.

Image may have been reduced in size. Click image to view fullscreen.


Right half. no thrust bearing, all have tangs.

Image may have been reduced in size. Click image to view fullscreen.

_________________
My Toys: '75 Porsche 914, '86 VW MK1 Cabriolet (sold), '92 Ski Nautique and now a 1972 VW Transporter Deluxe (under construction)
Back to top
View user's profile Send private message Send e-mail Gallery Classifieds Feedback
malcolm2
Samba Member


Joined: September 28, 2011
Posts: 727
Location: Mount Juliet, TN
malcolm2 is offline 

PostPosted: Mon Jun 08, 2020 2:25 pm    Post subject: Re: Let the process of saving 2222069996 begin Reply with quote

Crank and cam gears are indexed.

Image may have been reduced in size. Click image to view fullscreen.


case halves are bolted up. Used all new hardware from Type4store.com

Image may have been reduced in size. Click image to view fullscreen.

_________________
My Toys: '75 Porsche 914, '86 VW MK1 Cabriolet (sold), '92 Ski Nautique and now a 1972 VW Transporter Deluxe (under construction)
Back to top
View user's profile Send private message Send e-mail Gallery Classifieds Feedback
jtauxe Premium Member
Samba Member


Joined: September 30, 2004
Posts: 5464
Location: Los Alamos, New Mexico
jtauxe is offline 

PostPosted: Mon Jun 08, 2020 2:50 pm    Post subject: Re: Let the process of saving 2222069996 begin Reply with quote

malcolm2 wrote:
a month later....
<snip>
While I waited, I cleaned and tested the wiper motor and bought all the goodies for the wiper arm shafts and some used arms for $12 each. Buy the way, this black cap requires some drilling. I could not get it onto the shaft. And as you can see, it does not fully seat over the nut. Oh well...

Image may have been reduced in size. Click image to view fullscreen.

Image may have been reduced in size. Click image to view fullscreen.

I think the problem here is that your nuts are too fat. IIRC, they should be thinner, and that will also allow the plastic cover to completely cover them.
_________________
John
"Travelling in a fried-out Kombi, on a hippie trail, head full of zombie..." - Colin Hay and Ron Strykert
http://vw.tauxe.net
1969 Transporter, 1971 Westfalia, 1976, 1977, 1976, 1977, 1971, 1973, 1977 Westfalias,
1979 Champagne Sunroof, 1974 Westfalia Automatic, 1979 Transporter, 1972 Sportsmobile, 1973 Transporter Wild Westerner, 1974 Westfalia parts bus
, 1975 Mexican single cab *FOR SALE*, 1978 Irish 4-door double cab RHD
Back to top
View user's profile Send private message Visit poster's website Gallery Classifieds Feedback
malcolm2
Samba Member


Joined: September 28, 2011
Posts: 727
Location: Mount Juliet, TN
malcolm2 is offline 

PostPosted: Tue Jun 09, 2020 8:04 am    Post subject: Re: Let the process of saving 2222069996 begin Reply with quote

Meant to include some pix of the thrust bearing fix.

Image may have been reduced in size. Click image to view fullscreen.

Image may have been reduced in size. Click image to view fullscreen.

Image may have been reduced in size. Click image to view fullscreen.

_________________
My Toys: '75 Porsche 914, '86 VW MK1 Cabriolet (sold), '92 Ski Nautique and now a 1972 VW Transporter Deluxe (under construction)
Back to top
View user's profile Send private message Send e-mail Gallery Classifieds Feedback
malcolm2
Samba Member


Joined: September 28, 2011
Posts: 727
Location: Mount Juliet, TN
malcolm2 is offline 

PostPosted: Tue Jun 09, 2020 8:20 am    Post subject: Re: Let the process of saving 2222069996 begin Reply with quote

I have purchased and installed a new distributor. A petronix flamethrower 3. The 3 module is the most up to date. Big feature is it won’t burn up if you leave the key on.

Aircooled.net was helpful in the purchase and some issues after i got it. They recommended for me to disassemble the unit. Clean is and polish where the two plates touch. Lube and re assemble.

What i found was the lobes touched the module. The seller and petronix said not to sorry. But i did. So I had slightly bend the tab that holds the plate. When the screw is tightened the plate moves just a bit and pulls the module away from the shaft. Smooth spinning now.


Image may have been reduced in size. Click image to view fullscreen.

Image may have been reduced in size. Click image to view fullscreen.

Image may have been reduced in size. Click image to view fullscreen.

_________________
My Toys: '75 Porsche 914, '86 VW MK1 Cabriolet (sold), '92 Ski Nautique and now a 1972 VW Transporter Deluxe (under construction)
Back to top
View user's profile Send private message Send e-mail Gallery Classifieds Feedback
malcolm2
Samba Member


Joined: September 28, 2011
Posts: 727
Location: Mount Juliet, TN
malcolm2 is offline 

PostPosted: Thu Jul 23, 2020 6:21 pm    Post subject: Re: Let the process of saving 2222069996 begin Reply with quote

Gettin there. These are Camper Specials from the type four store by HAM. He recommended the copper spray seal. Spray on within ten minutes of installation.
Image may have been reduced in size. Click image to view fullscreen.

Image may have been reduced in size. Click image to view fullscreen.

_________________
My Toys: '75 Porsche 914, '86 VW MK1 Cabriolet (sold), '92 Ski Nautique and now a 1972 VW Transporter Deluxe (under construction)
Back to top
View user's profile Send private message Send e-mail Gallery Classifieds Feedback
malcolm2
Samba Member


Joined: September 28, 2011
Posts: 727
Location: Mount Juliet, TN
malcolm2 is offline 

PostPosted: Sun Sep 13, 2020 3:31 pm    Post subject: Re: Let the process of saving 2222069996 begin Reply with quote

Image may have been reduced in size. Click image to view fullscreen.


Tranz is in. Word is it might be easier to assemble the engine and the tranz, then install. Like most things on these cars, I have to do them 2 or 3 times, so why should engine install be different.... If it happens, it happens. For now it is in the bus.

Tranz guy may have mentioned it, but I don't remember. My case and bell housing were swiss cheese. He got me replacements. Cool thing is the bell housing is a late one. I noticed the throw out lever etc.... were different when I was looking to install the bearing. Turns out the clutch kit came with a TO bearing and it is the one I now need. Yee Haw.


Image may have been reduced in size. Click image to view fullscreen.


ALL the cooling tins are installed. Found a heat shield that was in decent shape. Slatered it with some high temp paint, maybe it will last another 45 years.

Muffler as a whole was good. But the mounting holes and tail pipe bracket were super rusty.
Image may have been reduced in size. Click image to view fullscreen.

Image may have been reduced in size. Click image to view fullscreen.

Image may have been reduced in size. Click image to view fullscreen.


But I got the broken studs out, added a few thread sleeves, and bought SS hardware.
Image may have been reduced in size. Click image to view fullscreen.

_________________
My Toys: '75 Porsche 914, '86 VW MK1 Cabriolet (sold), '92 Ski Nautique and now a 1972 VW Transporter Deluxe (under construction)


Last edited by malcolm2 on Sun Sep 13, 2020 3:41 pm; edited 1 time in total
Back to top
View user's profile Send private message Send e-mail Gallery Classifieds Feedback
malcolm2
Samba Member


Joined: September 28, 2011
Posts: 727
Location: Mount Juliet, TN
malcolm2 is offline 

PostPosted: Sun Sep 13, 2020 3:34 pm    Post subject: Re: Let the process of saving 2222069996 begin Reply with quote

Image may have been reduced in size. Click image to view fullscreen.


If you remember, I got an engine hatch and welded it in. Yesterday, I trimmed up the insulation and the plates that hold it in. It fit nicely. I added a few tek screws and it is holding. I put a thin layer of B-Quiet on before I put the 45 year old insulation back. You can see thru the hatch to the roof, it has B-Quiet sheets on it too. Complete coverage is not required. It is a thick tar material that will absorb the vibrations of the metal panels. Gonna stick some in the doors and the side panels too.
_________________
My Toys: '75 Porsche 914, '86 VW MK1 Cabriolet (sold), '92 Ski Nautique and now a 1972 VW Transporter Deluxe (under construction)
Back to top
View user's profile Send private message Send e-mail Gallery Classifieds Feedback
malcolm2
Samba Member


Joined: September 28, 2011
Posts: 727
Location: Mount Juliet, TN
malcolm2 is offline 

PostPosted: Sun Oct 18, 2020 6:48 pm    Post subject: Re: Let the process of saving 2222069996 begin Reply with quote

Still drag-assin' around. You would think that "working from home" would give you more free time. But damn, I end up working 10-12 hours and then I am not motivated to do BUS work.

Anyway, Put some loaner Weber 40s on the engine and learned a bit about setting them up. 1. Clean them up. And set up the adjustment screws. 2. Get the engine started. 3. take the linkage off, and compare how it runs. The linkage is critical.

I did all that it worked great. Still don' t have the linkage set, but screw-up. Time to buy my own carbs.

So the Cam has been broken in, Timing has been set. All this took about 1.5 gallons of gas.


Image may have been reduced in size. Click image to view fullscreen.

_________________
My Toys: '75 Porsche 914, '86 VW MK1 Cabriolet (sold), '92 Ski Nautique and now a 1972 VW Transporter Deluxe (under construction)
Back to top
View user's profile Send private message Send e-mail Gallery Classifieds Feedback
malcolm2
Samba Member


Joined: September 28, 2011
Posts: 727
Location: Mount Juliet, TN
malcolm2 is offline 

PostPosted: Sun Oct 18, 2020 6:55 pm    Post subject: Re: Let the process of saving 2222069996 begin Reply with quote

OIL PRESSURE build up.....



Link


On this video, I have already set the carbs and attempted to set the linkage ( not such a good result). Set the timing, double checked the T-stat. Fixed an oil leak found during Cam Break-in. Re-checked the valve clearances on the Chromoly push-rods. Coated the cork valve cover gaskets with K2. I ran the tank out of gas.... and saw no oil leaks! I am calling this done!


Link
[youtube]
_________________
My Toys: '75 Porsche 914, '86 VW MK1 Cabriolet (sold), '92 Ski Nautique and now a 1972 VW Transporter Deluxe (under construction)
Back to top
View user's profile Send private message Send e-mail Gallery Classifieds Feedback
metz
Samba Member


Joined: March 31, 2005
Posts: 174
Location: Norway
metz is offline 

PostPosted: Mon Oct 19, 2020 11:52 pm    Post subject: Re: Let the process of saving 2222069996 begin Reply with quote

Looks and sounds great. Congrats!
_________________
68 panel
Back to top
View user's profile Send private message Gallery Classifieds Feedback
Display posts from previous:   
Reply to topic    Forum Index -> Bay Window Bus All times are Mountain Standard Time/Pacific Daylight Savings Time
Page: Previous  1, 2, 3, 4, 5, 6, 7
Page 7 of 7

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum

About | Help! | Advertise | Donate | Premium Membership | Privacy/Terms of Use | Contact Us | Site Map
Copyright © 1996-2020, Everett Barnes. All Rights Reserved.
Not affiliated with or sponsored by Volkswagen of America | Forum powered by phpBB