Author |
Message |
Ian Godfrey Samba Member
Joined: September 25, 2006 Posts: 1137 Location: Melbourne Australia
|
Posted: Sat May 15, 2021 6:58 pm Post subject: Re: O Ghia's Restoration Journey |
|
|
I have used just one spring, the one opposite the 2 adjusting screws. (RH in your pic)
but I don't know if this is 'correct' |
|
Back to top |
|
|
Marcdeb Samba Member
Joined: May 22, 2019 Posts: 3033 Location: Vermont
|
Posted: Mon May 17, 2021 11:14 am Post subject: Re: O Ghia's Restoration Journey |
|
|
Ian Godfrey wrote: |
I have used just one spring, the one opposite the 2 adjusting screws. (RH in your pic)
but I don't know if this is 'correct' |
I have found numerous pictures of headlight assemblies and it seems odd that so many have only one spring.
I can see that it still works but I am curious if there's a reason for using only one other than one gets lost or broken??
I managed to find one more spring so I'm putting 2 on both headlights. _________________ Marc
68 Karmann Ghia Cabrio Autostick
71 Karmann Ghia Cabrio
Previously Owned:
2011 VW EOS Hard Top Conv
2008 Saab 9-3 2.0T Conv
2003 Saab 9-3 SE Conv
2001 Saab 9-3 Conv
1998 BMW 3 Series Conv
1997 Saab 900 Conv
1997 Mazda Miata
68 Ghia Vert Survivor with 22,350 miles: https://www.thesamba.com/vw/forum/viewtopic.php?t=768107&highlight=
71 Ghia Vert Restoration: https://www.thesamba.com/vw/forum/viewtopic.php?t=726710&postorder=asc |
|
Back to top |
|
|
Marcdeb Samba Member
Joined: May 22, 2019 Posts: 3033 Location: Vermont
|
Posted: Mon May 17, 2021 11:53 am Post subject: Re: O Ghia's Restoration Journey |
|
|
I have 5 headliight bulbs. None have been tested yet. No two of them are a match which is not surprising.
Would any 2 of these be good choices as far as matching up a pair.?
Westinghouse "J14" "8361" that says "Drive Left" but also says "Not for use on USA Hghways!
Westinghouse "2" "8224" "6014" "R-Beam" ? I wasn't aware that these old Sealed Beam headlights are side specific. Are they?
Sylvania "2D1" "C10"
Wagner "2D1" "6014" "MZK31" "H83"
Wagner "2D1" "Halogen" "8255" "H6324"
Is the halogen light stronger?
Or should I just buy a new pair and if so, what should I install? Not interested in LED. _________________ Marc
68 Karmann Ghia Cabrio Autostick
71 Karmann Ghia Cabrio
Previously Owned:
2011 VW EOS Hard Top Conv
2008 Saab 9-3 2.0T Conv
2003 Saab 9-3 SE Conv
2001 Saab 9-3 Conv
1998 BMW 3 Series Conv
1997 Saab 900 Conv
1997 Mazda Miata
68 Ghia Vert Survivor with 22,350 miles: https://www.thesamba.com/vw/forum/viewtopic.php?t=768107&highlight=
71 Ghia Vert Restoration: https://www.thesamba.com/vw/forum/viewtopic.php?t=726710&postorder=asc |
|
Back to top |
|
|
Rome Samba Member
Joined: June 02, 2004 Posts: 9653 Location: Pearl River, NY
|
Posted: Mon May 17, 2021 5:57 pm Post subject: Re: O Ghia's Restoration Journey |
|
|
Quote: |
Westinghouse "2" "8224" "6014" "R-Beam" ? I wasn't aware that these old Sealed Beam headlights are side specific. Are they?
Sylvania "2D1" "C10"
Wagner "2D1" "6014" "MZK31" "H83"
Wagner "2D1" "Halogen" "8255" "H6324"
Is the halogen light stronger?
Or should I just buy a new pair and if so, what should I install? |
I researched the 6014 and the "R-Beam" designations on internet but could not find anything conclusive. 6014 and 6015 appear to be industry designations for 2-filament (high/low beam) 7" round sealed beams. R-Beam is likely a lamp designed with the light output pattern for right-hand traffic such as in the USA, and not a dedicated lamp for the right side of the car. Both lamps would be identical. R-Beam might also mean "round" headlamp vs the rectangular which was allowed on US cars as of 1974 ('75 model year), though unlikely because both words start with an "r".
On my '64 Ghia I installed Sylvania Halogen sealed-beam lamps in the 1990's. I've avoided driving at night for at least 20 years, but I do remember their light output as excellent and "sufficient". Those have a curved lens design, compared to the traditional flat lens on H4 high/low beam removable bulb style. |
|
Back to top |
|
|
Marcdeb Samba Member
Joined: May 22, 2019 Posts: 3033 Location: Vermont
|
Posted: Mon May 17, 2021 7:27 pm Post subject: Re: O Ghia's Restoration Journey |
|
|
Rome wrote: |
Quote: |
Westinghouse "2" "8224" "6014" "R-Beam" ? I wasn't aware that these old Sealed Beam headlights are side specific. Are they?
Sylvania "2D1" "C10"
Wagner "2D1" "6014" "MZK31" "H83"
Wagner "2D1" "Halogen" "8255" "H6324"
Is the halogen light stronger?
Or should I just buy a new pair and if so, what should I install? |
I researched the 6014 and the "R-Beam" designations on internet but could not find anything conclusive. 6014 and 6015 appear to be industry designations for 2-filament (high/low beam) 7" round sealed beams. R-Beam is likely a lamp designed with the light output pattern for right-hand traffic such as in the USA, and not a dedicated lamp for the right side of the car. Both lamps would be identical. R-Beam might also mean "round" headlamp vs the rectangular which was allowed on US cars as of 1974 ('75 model year), though unlikely because both words start with an "r".
On my '64 Ghia I installed Sylvania Halogen sealed-beam lamps in the 1990's. I've avoided driving at night for at least 20 years, but I do remember their light output as excellent and "sufficient". Those have a curved lens design, compared to the traditional flat lens on H4 high/low beam removable bulb style. |
The Sylvania Halogen comes up as H6024. I found one write up that states anything non halogen is out of date and should be replaced with halogen. _________________ Marc
68 Karmann Ghia Cabrio Autostick
71 Karmann Ghia Cabrio
Previously Owned:
2011 VW EOS Hard Top Conv
2008 Saab 9-3 2.0T Conv
2003 Saab 9-3 SE Conv
2001 Saab 9-3 Conv
1998 BMW 3 Series Conv
1997 Saab 900 Conv
1997 Mazda Miata
68 Ghia Vert Survivor with 22,350 miles: https://www.thesamba.com/vw/forum/viewtopic.php?t=768107&highlight=
71 Ghia Vert Restoration: https://www.thesamba.com/vw/forum/viewtopic.php?t=726710&postorder=asc |
|
Back to top |
|
|
Duncan67KG Samba Member
Joined: August 09, 2015 Posts: 33 Location: Southern California
|
Posted: Mon May 17, 2021 7:49 pm Post subject: Re: O Ghia's Restoration Journey |
|
|
I am running the Sylvania halogens and I am very happy with them while driving at night. Back in the 80’s I ran the Hella H4’s and they were brighter than anything available at the time but I never really liked the look of the flat lens. _________________ Duncan
1967 Ghia Coupe |
|
Back to top |
|
|
Marcdeb Samba Member
Joined: May 22, 2019 Posts: 3033 Location: Vermont
|
Posted: Tue May 18, 2021 6:01 pm Post subject: Re: O Ghia's Restoration Journey |
|
|
Duncan67KG wrote: |
I am running the Sylvania halogens and I am very happy with them while driving at night. Back in the 80’s I ran the Hella H4’s and they were brighter than anything available at the time but I never really liked the look of the flat lens. |
Good to know. Thank you. The Sylvania H6024 Halogens were in stock at the local O'Reilly's. The package says rated for 150 hours
Might be changing headlights with every other oil change! I don't plan to drive at night much, but I am planning to have them
on during the day just to make sure the car is easily seen. They look great and as long as they work, I'm happy.
_________________ Marc
68 Karmann Ghia Cabrio Autostick
71 Karmann Ghia Cabrio
Previously Owned:
2011 VW EOS Hard Top Conv
2008 Saab 9-3 2.0T Conv
2003 Saab 9-3 SE Conv
2001 Saab 9-3 Conv
1998 BMW 3 Series Conv
1997 Saab 900 Conv
1997 Mazda Miata
68 Ghia Vert Survivor with 22,350 miles: https://www.thesamba.com/vw/forum/viewtopic.php?t=768107&highlight=
71 Ghia Vert Restoration: https://www.thesamba.com/vw/forum/viewtopic.php?t=726710&postorder=asc |
|
Back to top |
|
|
Trylon Samba Member
Joined: August 16, 2019 Posts: 4853 Location: Connecticut
|
Posted: Wed May 19, 2021 4:34 am Post subject: Re: O Ghia's Restoration Journey |
|
|
Hey, I think you are officially ahead of me now! _________________ 1973 Porsche 914 2.0
1959 Volkswagen Karmann Ghia
1979 Volkswagen Rabbit
1973 Volkswagen Bus
1970 MGB-GT
1962 Oldsmobile Jetfire
More tomfoolery on
The Karmann Ghia Fever YouTube Channel! |
|
Back to top |
|
|
Marcdeb Samba Member
Joined: May 22, 2019 Posts: 3033 Location: Vermont
|
Posted: Wed May 19, 2021 8:08 am Post subject: Re: O Ghia's Restoration Journey |
|
|
Trylon wrote: |
Hey, I think you are officially ahead of me now! |
Feels like I'm moving at a snails pace. Lots of work ahead with doors which are only empty shells right now.
Like you, I have lots of small things that are not needed for state inspection so they will have to wait. _________________ Marc
68 Karmann Ghia Cabrio Autostick
71 Karmann Ghia Cabrio
Previously Owned:
2011 VW EOS Hard Top Conv
2008 Saab 9-3 2.0T Conv
2003 Saab 9-3 SE Conv
2001 Saab 9-3 Conv
1998 BMW 3 Series Conv
1997 Saab 900 Conv
1997 Mazda Miata
68 Ghia Vert Survivor with 22,350 miles: https://www.thesamba.com/vw/forum/viewtopic.php?t=768107&highlight=
71 Ghia Vert Restoration: https://www.thesamba.com/vw/forum/viewtopic.php?t=726710&postorder=asc |
|
Back to top |
|
|
obus Samba Member
Joined: March 08, 2001 Posts: 11069 Location: just off Garden State Parkway Exit 81
|
|
Back to top |
|
|
Marcdeb Samba Member
Joined: May 22, 2019 Posts: 3033 Location: Vermont
|
Posted: Wed May 19, 2021 7:10 pm Post subject: Re: O Ghia's Restoration Journey |
|
|
obus wrote: |
If you are moving at snails pace then what is my Ghias pace?
Yours looks great! |
Thank you. I've read many times on this site to just do something every day so I try to follow that advice. Sometimes it's just doing research or buy a part.
Your car is quite a find. I just love looking at the gaps on your car. The are so even. _________________ Marc
68 Karmann Ghia Cabrio Autostick
71 Karmann Ghia Cabrio
Previously Owned:
2011 VW EOS Hard Top Conv
2008 Saab 9-3 2.0T Conv
2003 Saab 9-3 SE Conv
2001 Saab 9-3 Conv
1998 BMW 3 Series Conv
1997 Saab 900 Conv
1997 Mazda Miata
68 Ghia Vert Survivor with 22,350 miles: https://www.thesamba.com/vw/forum/viewtopic.php?t=768107&highlight=
71 Ghia Vert Restoration: https://www.thesamba.com/vw/forum/viewtopic.php?t=726710&postorder=asc |
|
Back to top |
|
|
c21darrel Samba Member
Joined: January 22, 2009 Posts: 8211 Location: San Dimas
|
|
Back to top |
|
|
rbsurfguy Samba Member
Joined: August 10, 2008 Posts: 1757 Location: Fairfax, Northern Virginia Formerly Huntington Beach, SoCal
|
Posted: Fri May 21, 2021 6:33 am Post subject: Re: O Ghia's Restoration Journey |
|
|
I find at times I go out to the Ghia Haus and just sit and stare at it, or touch parts, or fantasize how it will look with the upholstery and top in place, still trying to figure out color of all. Does that count as spending time with it and doing something? I think so.
I also find myself, too may times, waiting for postings on the Samba and get anxious when no one posts!!!
Jeff _________________ 1971 Ghia convertible (Body off rebuild)
2019 VW Atlas 4Motion
2012 Passat-Sold
See my build on The Samba at:
Jeff's 71 Vert Restoration/Reassembly http://www.thesamba.com/vw/forum/viewtopic.php?t=6...highlight= |
|
Back to top |
|
|
Marcdeb Samba Member
Joined: May 22, 2019 Posts: 3033 Location: Vermont
|
Posted: Fri May 21, 2021 7:03 am Post subject: Re: O Ghia's Restoration Journey |
|
|
rbsurfguy wrote: |
I find at times I go out to the Ghia Haus and just sit and stare at it, or touch parts, or fantasize how it will look with the upholstery and top in place, still trying to figure out color of all. Does that count as spending time with it and doing something? I think so.
I also find myself, too may times, waiting for postings on the Samba and get anxious when no one posts!!!
Jeff |
For me yes. Some days I just do planning, looking for related threads and thinking ahead. Even clean up and get organized again. While the car was in the body shop, I kept thinking about cleaning and restoring parts like window mechanisms, or tail lights, but without the car at my disposal, I though it was pointless. Now that I'm actually doing this, I see that it was the right way to do it. I really need the car here to prep the parts that go back on. _________________ Marc
68 Karmann Ghia Cabrio Autostick
71 Karmann Ghia Cabrio
Previously Owned:
2011 VW EOS Hard Top Conv
2008 Saab 9-3 2.0T Conv
2003 Saab 9-3 SE Conv
2001 Saab 9-3 Conv
1998 BMW 3 Series Conv
1997 Saab 900 Conv
1997 Mazda Miata
68 Ghia Vert Survivor with 22,350 miles: https://www.thesamba.com/vw/forum/viewtopic.php?t=768107&highlight=
71 Ghia Vert Restoration: https://www.thesamba.com/vw/forum/viewtopic.php?t=726710&postorder=asc |
|
Back to top |
|
|
obus Samba Member
Joined: March 08, 2001 Posts: 11069 Location: just off Garden State Parkway Exit 81
|
Posted: Fri May 21, 2021 8:03 am Post subject: Re: O Ghia's Restoration Journey |
|
|
Marcdeb wrote: |
rbsurfguy wrote: |
I find at times I go out to the Ghia Haus and just sit and stare at it, or touch parts, or fantasize how it will look with the upholstery and top in place, still trying to figure out color of all. Does that count as spending time with it and doing something? I think so.
I also find myself, too may times, waiting for postings on the Samba and get anxious when no one posts!!!
Jeff |
For me yes. Some days I just do planning, looking for related threads and thinking ahead. Even clean up and get organized again. While the car was in the body shop, I kept thinking about cleaning and restoring parts like window mechanisms, or tail lights, but without the car at my disposal, I though it was pointless. Now that I'm actually doing this, I see that it was the right way to do it. I really need the car here to prep the parts that go back on. |
well your planning is serving you well thus far! keep on planning! _________________ July 1959 Mango Standard Bus aka Obus L346 L347 https://www.thesamba.com/vw/forum/viewtopic.php?t=256592&highlight=
June 1973 Pumpkin Orange Thing aka Othing L30H
https://www.thesamba.com/vw/forum/viewtopic.php?t=711775&highlight=
1960 Paprika Red Karmann Ghia Convertible aka Schatze L452 built 5/20/60
https://www.thesamba.com/vw/forum/viewtopic.php?t=...highlight=
66 21 window bus built 8/31/65 https://www.thesamba.com/vw/forum/viewtopic.php?t=777273 |
|
Back to top |
|
|
Marcdeb Samba Member
Joined: May 22, 2019 Posts: 3033 Location: Vermont
|
Posted: Sat May 22, 2021 10:30 am Post subject: Re: O Ghia's Restoration Journey |
|
|
What am I doing wrong!!!
I believe I have all the right parts on the front but these bracket covers again will not let the bumper move all the way in.
The inside lower corner of the bracket cover makes contact with the body while the rest of the covers are as much as 3/8 inch clearance.
What am I doing wrong?
I left all the bolts loose so that I have play in all the parts. It's like I need to pull the bracket covers back but they are already all the way back??
The front of the car has never been hit. There is no body work anywhere on the front.
I'm wondering if, like the back bumper, these bracket covers and/or tubes again are the wrong parts for a 71.
_________________ Marc
68 Karmann Ghia Cabrio Autostick
71 Karmann Ghia Cabrio
Previously Owned:
2011 VW EOS Hard Top Conv
2008 Saab 9-3 2.0T Conv
2003 Saab 9-3 SE Conv
2001 Saab 9-3 Conv
1998 BMW 3 Series Conv
1997 Saab 900 Conv
1997 Mazda Miata
68 Ghia Vert Survivor with 22,350 miles: https://www.thesamba.com/vw/forum/viewtopic.php?t=768107&highlight=
71 Ghia Vert Restoration: https://www.thesamba.com/vw/forum/viewtopic.php?t=726710&postorder=asc |
|
Back to top |
|
|
sputnick60 Samba Moderator
Joined: July 22, 2007 Posts: 3916 Location: In Molinya Orbit
|
Posted: Sat May 22, 2021 3:42 pm Post subject: Re: O Ghia's Restoration Journey |
|
|
Bumpers have probably been banged around in their lives and the fittings are not to the original shape. You’re going to need reshape things if you are after an exacting fit. Here a some things to consider. A combination might work well enough to close the gap for you.
The covers aren’t supposed to have that flare those seem to have, especially past the attachment bolt. Straightening should have occurred before paint. I don’t see where you have the grommeting glued to the edge facing towards the body. Such grommeting will add a small amount of thickness and close the gap a little more. .
You could try angling the irons upwards. With all that weight it would be natural for the bumpers to sag. Get a jack under each overrider to lift while you reach over the nose with your spanner and tighten. Rest your weight on the car to add as much push as you need.
The support piece has that zig zag which affects the position of the cover. Maybe you can open out the zig zag to get a few millimetres.
The irons have a slotted hole towards the bumper. There is also the curve through 90 degrees they have to meet the bumper. if the curve is an incorrect radius it will put the bumper a fraction out of position. The bolts will go though the slots but the result will be slightly out.
You could try working with just the irons and the covers until you are satisfied with the fit, then build up the rest of the bumpers on the car.
Nicholas. _________________ '66 Karmann Ghia Cabriolet...
'65 Porsche 356C Coupe...
2005 Mecedes Benz C180 Kompressor Estate
Stop dead photo links! Post your photos to The Samba Gallery! |
|
Back to top |
|
|
c21darrel Samba Member
Joined: January 22, 2009 Posts: 8211 Location: San Dimas
|
Posted: Sat May 22, 2021 5:02 pm Post subject: Re: O Ghia's Restoration Journey |
|
|
sputnick60 wrote: |
Bumpers have probably been banged around in their lives and the fittings are not to the original shape. You’re going to need reshape things if you are after an exacting fit. Here a some things to consider. A combination might work well enough to close the gap for you.
The covers aren’t supposed to have that flare those seem to have, especially past the attachment bolt. Straightening should have occurred before paint. I don’t see where you have the grommeting glued to the edge facing towards the body. Such grommeting will add a small amount of thickness and close the gap a little more. .
You could try angling the irons upwards. With all that weight it would be natural for the bumpers to sag. Get a jack under each overrider to lift while you reach over the nose with your spanner and tighten. Rest your weight on the car to add as much push as you need.
The support piece has that zig zag which affects the position of the cover. Maybe you can open out the zig zag to get a few millimetres.
The irons have a slotted hole towards the bumper. There is also the curve through 90 degrees they have to meet the bumper. if the curve is an incorrect radius it will put the bumper a fraction out of position. The bolts will go though the slots but the result will be slightly out.
You could try working with just the irons and the covers until you are satisfied with the fit, then build up the rest of the bumpers on the car.
Nicholas. |
Great post with lots of knowledge on assembly process.
I would add, you can oval out mount holes to give you more movement, you can shim where needed under bolts (washers) to push out, between bumper mount and bumper.... You can re-form covers, trim/file them as last resort. All the mounts and supports are same size year after year. If you want perfect, it takes extra effort. Compete re-assembly prior to paint helps, but even then you get surprised. Surprise!
Plenty of ghias on the road may not even have the covers installed, and almost no one notices. _________________ GhiaBuild
http://www.thesamba.com/vw/forum/viewtopic.php?t=481184
1967 DC build
https://www.thesamba.com/vw/forum/viewtopic.php?t=693583&highlight=67+dc
Stop dead photo links! Post your photos to The Samba Gallery! |
|
Back to top |
|
|
Marcdeb Samba Member
Joined: May 22, 2019 Posts: 3033 Location: Vermont
|
Posted: Sat May 22, 2021 5:13 pm Post subject: Re: O Ghia's Restoration Journey |
|
|
sputnick60 wrote: |
Bumpers have probably been banged around in their lives and the fittings are not to the original shape. You’re going to need reshape things if you are after an exacting fit. Here a some things to consider. A combination might work well enough to close the gap for you.
The covers aren’t supposed to have that flare those seem to have, especially past the attachment bolt. Straightening should have occurred before paint. I don’t see where you have the grommeting glued to the edge facing towards the body. Such grommeting will add a small amount of thickness and close the gap a little more. .
You could try angling the irons upwards. With all that weight it would be natural for the bumpers to sag. Get a jack under each overrider to lift while you reach over the nose with your spanner and tighten. Rest your weight on the car to add as much push as you need.
The support piece has that zig zag which affects the position of the cover. Maybe you can open out the zig zag to get a few millimetres.
The irons have a slotted hole towards the bumper. There is also the curve through 90 degrees they have to meet the bumper. if the curve is an incorrect radius it will put the bumper a fraction out of position. The bolts will go though the slots but the result will be slightly out.
You could try working with just the irons and the covers until you are satisfied with the fit, then build up the rest of the bumpers on the car.
Nicholas. |
Great tips. Thank you again Nicolas. So fortunate to have all the advise from people on this forum. These parts were painted
by the previous owner and I assumed I could use them as is. They were on the car when it arrived. The rubber seals to cover the
forward edge came with the car but not installed. I plan to install them once I ensure that I have everything fitted. I am hoping to
avoid gluing them though
I went through some boxes that I had forgotten about. Parts that I had bought from a 71 Vert from Chicago. Fortunately I have
a 2nd set of these parts for comparison. The covers themselves seem to be formed pretty much the same. The irons though are bent
differently on the bracket end. I am 100% sure that the blue parts are original to the 71 model year. But I discovered that one of
the ivory irons is bent outward at the end, basically elongating it. I will have to fix the longer iron. And one of the blue irons is
missing the welded on nut and they don't both have the same angle coming off from the towel bar. One of them is bent for sure.
But my goal is to reuse the ivory set if possible.
You are correct about the angle of the bumper, I realize now that I did not observe that as much as I should have. I was more
concerned about getting the 4 bracket bolts into the car.
I placed just the covers up against the car and the contour seems to fit well so I need to pay attention to the angle of the bumper.
I am wondering if it might help to remove the bolt from the cover and back it off until the bumper is roughly in position?? _________________ Marc
68 Karmann Ghia Cabrio Autostick
71 Karmann Ghia Cabrio
Previously Owned:
2011 VW EOS Hard Top Conv
2008 Saab 9-3 2.0T Conv
2003 Saab 9-3 SE Conv
2001 Saab 9-3 Conv
1998 BMW 3 Series Conv
1997 Saab 900 Conv
1997 Mazda Miata
68 Ghia Vert Survivor with 22,350 miles: https://www.thesamba.com/vw/forum/viewtopic.php?t=768107&highlight=
71 Ghia Vert Restoration: https://www.thesamba.com/vw/forum/viewtopic.php?t=726710&postorder=asc |
|
Back to top |
|
|
Marcdeb Samba Member
Joined: May 22, 2019 Posts: 3033 Location: Vermont
|
Posted: Sat May 22, 2021 5:30 pm Post subject: Re: O Ghia's Restoration Journey |
|
|
c21darrel wrote: |
sputnick60 wrote: |
Bumpers have probably been banged around in their lives and the fittings are not to the original shape. You’re going to need reshape things if you are after an exacting fit. Here a some things to consider. A combination might work well enough to close the gap for you.
The covers aren’t supposed to have that flare those seem to have, especially past the attachment bolt. Straightening should have occurred before paint. I don’t see where you have the grommeting glued to the edge facing towards the body. Such grommeting will add a small amount of thickness and close the gap a little more. .
You could try angling the irons upwards. With all that weight it would be natural for the bumpers to sag. Get a jack under each overrider to lift while you reach over the nose with your spanner and tighten. Rest your weight on the car to add as much push as you need.
The support piece has that zig zag which affects the position of the cover. Maybe you can open out the zig zag to get a few millimetres.
The irons have a slotted hole towards the bumper. There is also the curve through 90 degrees they have to meet the bumper. if the curve is an incorrect radius it will put the bumper a fraction out of position. The bolts will go though the slots but the result will be slightly out.
You could try working with just the irons and the covers until you are satisfied with the fit, then build up the rest of the bumpers on the car.
Nicholas. |
Great post with lots of knowledge on assembly process.
I would add, you can oval out mount holes to give you more movement, you can shim where needed under bolts (washers) to push out, between bumper mount and bumper.... You can re-form covers, trim/file them as last resort. All the mounts and supports are same size year after year. If you want perfect, it takes extra effort. Compete re-assembly prior to paint helps, but even then you get surprised. Surprise!
Plenty of ghias on the road may not even have the covers installed, and almost no one notices. |
Yes, I've seen many photos of Ghias with no bumper bracket covers. But my car will have all it's parts if I can help it.
I was wondering about adding washers and enlarging the holes to give me more wiggle room, but I also feel like if it went together
properly once, then I'll do my best to get it together again the same way. At some point when all my ideas are exhausted as well as those
offered up by others, then I'll do what I have to do!
Thank you for the help. _________________ Marc
68 Karmann Ghia Cabrio Autostick
71 Karmann Ghia Cabrio
Previously Owned:
2011 VW EOS Hard Top Conv
2008 Saab 9-3 2.0T Conv
2003 Saab 9-3 SE Conv
2001 Saab 9-3 Conv
1998 BMW 3 Series Conv
1997 Saab 900 Conv
1997 Mazda Miata
68 Ghia Vert Survivor with 22,350 miles: https://www.thesamba.com/vw/forum/viewtopic.php?t=768107&highlight=
71 Ghia Vert Restoration: https://www.thesamba.com/vw/forum/viewtopic.php?t=726710&postorder=asc |
|
Back to top |
|
|
|