Author |
Message |
62kellison Samba Member
Joined: March 28, 2018 Posts: 513 Location: mass
|
Posted: Tue Jan 08, 2019 6:54 am Post subject: 3 ridge hood design |
|
|
once in a while I put this out there hoping some new person with info will read it.I have the 3 ridge hood design if anyone has any info on it.I am pretty sure its a kellison sandpiper roadster the body matches everywhere except the hood..yes I have checked dune buggy archives and sambas ID archive with no luck yet.thanx SEAN....I am just curious,the hood does have the factory color (gelcoat) like the rest of the body..1 piece hood and dash.
|
|
Back to top |
|
|
Dale M. Samba Member
Joined: April 12, 2006 Posts: 20380 Location: Just a tiny bit west of Yosemite Valley
|
Posted: Tue Jan 08, 2019 7:25 am Post subject: Re: 3 ridge hood design |
|
|
Not sure if your buggy body is a Kellsion.... I have what I believe is a Sand Piper Roadster and the back area over carburetor is different from yours.... Mine does not have the flat top edge of tub out over carburetor, my has a roll down to the a bump out just like a real Manx has.... Mine also has a single rib down the hood...
Dale _________________ “Fear The Government That Wants To Take Your Guns" - Thomas Jefferson.
"Kellison Sand Piper Roadster" For Street & Show.
"Joe Pody Sandrover" Buggy with 2180 for Autocross (Sold)
============================================================
All suggestions and advice are purely my own opinion. You are free to ignore them if you wish ... |
|
Back to top |
|
|
62kellison Samba Member
Joined: March 28, 2018 Posts: 513 Location: mass
|
Posted: Tue Jan 08, 2019 8:09 am Post subject: Re: 3 ridge hood design |
|
|
do u have tubes under on both sides Dale for wiring?.like the manx?.I have tubes on both sides also.thanx Sean |
|
Back to top |
|
|
62kellison Samba Member
Joined: March 28, 2018 Posts: 513 Location: mass
|
Posted: Tue Jan 08, 2019 8:10 am Post subject: Re: 3 ridge hood design |
|
|
any info is good info,thanx Dale.I also have the flat plate sort of side pods with the "mud flap" attached to them.just have not re installed yet.
Last edited by 62kellison on Thu Jan 10, 2019 3:31 pm; edited 1 time in total |
|
Back to top |
|
|
goodsofar Samba Member
Joined: September 16, 2017 Posts: 31
|
Posted: Tue Jan 08, 2019 12:43 pm Post subject: Re: 3 ridge hood design |
|
|
Looks a lot like mine, but my dash and hood are separate pieces.
I haven't been able to tell for sure what mine is.
|
|
Back to top |
|
|
62kellison Samba Member
Joined: March 28, 2018 Posts: 513 Location: mass
|
Posted: Tue Jan 08, 2019 5:11 pm Post subject: Re: 3 ridge hood design |
|
|
goodsofar mine has a groove/seam all the way around the dash under windshield and up the sides.it looks like it could of been glued together hard to tell.didnt know if its been glued or it was from the mold.it may have been glued together onto the hood. thanx sean |
|
Back to top |
|
|
slalombuggy Samba Member
Joined: July 17, 2010 Posts: 9147 Location: Canada
|
Posted: Wed Jan 09, 2019 6:41 am Post subject: Re: 3 ridge hood design |
|
|
Unless they used a mold that separated to get the hood out, the hood and dash would have to be 2 separate pieces or it would be locked in the mold by the protrusion on the dash and the fact that the front of the hood curls back. So chances are the hood and dash are glued together.
brad |
|
Back to top |
|
|
62kellison Samba Member
Joined: March 28, 2018 Posts: 513 Location: mass
|
Posted: Thu Jan 10, 2019 3:29 pm Post subject: Re: 3 ridge hood design |
|
|
thanks for the info Brad and the search continues.lol Sean... |
|
Back to top |
|
|
Wheeler72 Samba Member
Joined: September 01, 2021 Posts: 1 Location: United States
|
Posted: Wed Sep 01, 2021 1:44 pm Post subject: Re: 3 ridge hood design |
|
|
I have the same buggy and hood. No info on it.
|
|
Back to top |
|
|
|