Author |
Message |
JMCFAN Samba Member
Joined: May 10, 2020 Posts: 46 Location: Corrales, NM
|
Posted: Sat Oct 23, 2021 3:15 pm Post subject: Ignition Switch wiring... |
|
|
Finishing up my Rebel harness install... so awesome... question on ignition switch...
Switch has...
Bat
IGN
Sol
Harness has
Ignition Switch power
Ignition Switch Start
Ignition Switch Ignition
Coil...
??? |
|
Back to top |
|
|
MrGoodtunes Samba Member
Joined: May 14, 2012 Posts: 851 Location: South Florida
|
Posted: Sat Oct 23, 2021 3:33 pm Post subject: Re: Ignition Switch wiring... |
|
|
JMCFAN wrote: |
... Switch has...
Bat
IGN
Sol
Harness has
Ignition Switch power
Ignition Switch Start
Ignition Switch Ignition
Coil...
??? |
Connect Bat to Ignition Switch power and on to +12v (battery positive).
Connect IGN to Ignition Switch Ignition and on to + terminal on ignition coil.
Connect Sol to Ignition Switch Start and on to starter solenoid male spade terminal.
Makes sense? |
|
Back to top |
|
|
JMCFAN Samba Member
Joined: May 10, 2020 Posts: 46 Location: Corrales, NM
|
Posted: Sat Oct 23, 2021 3:56 pm Post subject: Re: Ignition Switch wiring... |
|
|
MrGoodtunes wrote: |
JMCFAN wrote: |
... Switch has...
Bat
IGN
Sol
Harness has
Ignition Switch power
Ignition Switch Start
Ignition Switch Ignition
Coil...
??? |
Connect Bat to Ignition Switch power and on to +12v (battery positive).
Connect IGN to Ignition Switch Ignition and on to + terminal on ignition coil.
Connect Sol to Ignition Switch Start and on to starter solenoid male spade terminal.
Makes sense? |
Sorry....not really.. the "and on" is confusing me a bit.... |
|
Back to top |
|
|
MrGoodtunes Samba Member
Joined: May 14, 2012 Posts: 851 Location: South Florida
|
Posted: Sat Oct 23, 2021 4:26 pm Post subject: Re: Ignition Switch wiring... |
|
|
[quote="JMCFAN"... the "and on" is confusing ...[/quote]
Sorry. Let me try it this way:
(1) Harness wire Ignition Switch power - Connect one end of that wire to Bat on ignition switch, and the other end to +12v (i.e. positive battery terminal, or a fuse that's always +12v when fuse is not blown).
(2) Harness wire Ignition Switch Start - Connect one end of that wire to Sol on ignition switch, and the other end to male spade terminal on starter solenoid.
(3) Harness wire Ignition Switch Ignition - Connect one end of that wire to IGN on ignition switch, and the other end to + terminal on ignition coil. |
|
Back to top |
|
|
Dale M. Samba Member
Joined: April 12, 2006 Posts: 20377 Location: Just a tiny bit west of Yosemite Valley
|
Posted: Sat Oct 23, 2021 5:08 pm Post subject: Re: Ignition Switch wiring... |
|
|
On ignition switch...
BAT is source of 12 volts (battery).
IGN is to + side of coil (and any other devices that power is controlled by ignition switch).
SOL is to terminal 50 of starter solenoid.
Sort of like graphic below....
_________________ “Fear The Government That Wants To Take Your Guns" - Thomas Jefferson.
"Kellison Sand Piper Roadster" For Street & Show.
"Joe Pody Sandrover" Buggy with 2180 for Autocross (Sold)
============================================================
All suggestions and advice are purely my own opinion. You are free to ignore them if you wish ...
Last edited by Dale M. on Sat Oct 23, 2021 5:14 pm; edited 1 time in total |
|
Back to top |
|
|
JMCFAN Samba Member
Joined: May 10, 2020 Posts: 46 Location: Corrales, NM
|
Posted: Sat Oct 23, 2021 5:09 pm Post subject: Re: Ignition Switch wiring... |
|
|
MrGoodtunes wrote: |
[quote="JMCFAN"... the "and on" is confusing ... |
Sorry. Let me try it this way:
(1) Harness wire Ignition Switch power - Connect one end of that wire to Bat on ignition switch, and the other end to +12v (i.e. positive battery terminal, or a fuse that's always +12v when fuse is not blown).
(2) Harness wire Ignition Switch Start - Connect one end of that wire to Sol on ignition switch, and the other end to male spade terminal on starter solenoid.
(3) Harness wire Ignition Switch Ignition - Connect one end of that wire to IGN on ignition switch, and the other end to + terminal on ignition coil.[/quote]
Ok Thanks! will ohm them out since the harness is one piece. Just have 4 wires and 3 spades on the switch |
|
Back to top |
|
|
|