Author |
Message |
mark.konney@alliedprintin Samba Member
Joined: May 26, 2017 Posts: 28 Location: Connecticut
|
Posted: Tue May 17, 2022 7:11 am Post subject: Brake Bleeding |
|
|
Hi All!
I've been picking away at all the problems the PO left me with on our MANX.
Just replaced the clutch, pressure plate and throw out bearing, along with all wheel cylinders, all brake shoes and rear drums. The reason I changed the wheel cylinders was the buggy had no stopping power, and found that every single one of them had a frozen piston.
About 2 years ago I changed the Single Master cylinder to a Dual Master cylinder.
The problem I have now is that I cannot get any brake pedal to come back.
I started with a vacuum bleeder at the furthest wheel, doing them all, one by one, over and over. Still no pedal.
I tried the old fashion way same order and still no pedal. I'm very careful watching the level in the reservoir too.
What am I doing wrong?? Has the Master cylinder failed??
Please help!
Madmax26
|
|
Back to top |
|
|
Dangib Samba Member
Joined: October 05, 2011 Posts: 95 Location: pittsburgh
|
Posted: Tue May 17, 2022 8:20 am Post subject: Re: Brake Bleeding |
|
|
My bro had empi calipers he had to remove from car and bleed bc the bleeder isnt on the top so air gets trapped. |
|
Back to top |
|
|
MrGoodtunes Samba Member
Joined: May 14, 2012 Posts: 852 Location: South Florida
|
Posted: Tue May 17, 2022 12:05 pm Post subject: Re: Brake Bleeding |
|
|
mark.konney@alliedprintin wrote: |
... changed the Single Master cylinder to a Dual Master cylinder... started with a vacuum bleeder at the furthest wheel ... |
Forget about using vacuum bleeder, they tend to suck air into system. Also, due to the in-line arrangement of the VW dual master cylinder; you should bleed front right first, then front left, and then rear right & left after that.
If you still can't get good pedal; tighten all 8 brake shoes as much as possible, and re-do bleeding process all over again. And if this still fails, jack up front left as high as possible to raise your brake fluid reservoir up high. Then, lower right side of car (especially rear right). Open right side wheel cylinder bleeders, and wait for gravity to do its thing. And if even this fails, it's time to replace flexible brake hoses!
Oh wait, I'm assuming your brake pedal pushrod is adjusted propperly. If not, this could be the cause of your troubles. You need to make sure that when pedal is released so it comes back to floor stop plate, the pushrod will have completely released itself from master cylinder piston. Otherwise, flow from reservoir thru master to wheels will be block'd! So, check that you have the correct dimension "S" shown here:
|
|
Back to top |
|
|
Q-Dog Samba Member
Joined: April 05, 2010 Posts: 8700 Location: Sunset, Louisiana
|
Posted: Tue May 17, 2022 3:01 pm Post subject: Re: Brake Bleeding |
|
|
I would tighten up all of the brake shoes so they are dragging pretty good then get a helper and try bleeding again. Don't bother with the vacuum bleeder. _________________ Brian
'69 Dune Buggy
'69 Beetle Convertible
'70 Beetle |
|
Back to top |
|
|
mark.konney@alliedprintin Samba Member
Joined: May 26, 2017 Posts: 28 Location: Connecticut
|
Posted: Wed May 18, 2022 4:32 am Post subject: Re: Brake Bleeding |
|
|
Thanks for the help!
I'll start with the pedal push rod, then tighten up all brake adjusters and give it a shot again.
I'll let you know how I make out!
Thanks again |
|
Back to top |
|
|
tcmia Samba Member
Joined: April 30, 2019 Posts: 212 Location: Cleveland TN
|
Posted: Wed May 18, 2022 5:41 am Post subject: Re: Brake Bleeding |
|
|
I had similar issues. Q-dog's procedure worked for me. |
|
Back to top |
|
|
jspbtown Samba Member
Joined: January 27, 2004 Posts: 5157
|
Posted: Wed May 18, 2022 6:24 am Post subject: Re: Brake Bleeding |
|
|
I have never successfully bled a VW's brakes without tightening all the shoes against the drums. |
|
Back to top |
|
|
manxvair Samba Member
Joined: January 11, 2011 Posts: 231 Location: Arizona
|
Posted: Sun May 22, 2022 9:11 am Post subject: Re: Brake Bleeding |
|
|
To help prime the system, I installed a tire valve stem into a spare resevoir cap and then used a bicycle hand tire pump to pressurize the system and push fluid through. You don't need much pressure, but monitor the fluid level. |
|
Back to top |
|
|
mark.konney@alliedprintin Samba Member
Joined: May 26, 2017 Posts: 28 Location: Connecticut
|
Posted: Tue May 31, 2022 7:56 am Post subject: Re: Brake Bleeding |
|
|
Thank you all for the help!
I'll let you know how I make out! |
|
Back to top |
|
|
didget69 Samba Member
Joined: July 22, 2004 Posts: 4927 Location: Raleigh, North Carolina
|
Posted: Wed Jul 13, 2022 6:01 pm Post subject: Re: Brake Bleeding |
|
|
MrGoodtunes wrote: |
mark.konney@alliedprintin wrote: |
... changed the Single Master cylinder to a Dual Master cylinder... started with a vacuum bleeder at the furthest wheel ... |
Forget about using vacuum bleeder, they tend to suck air into system. Also, due to the in-line arrangement of the VW dual master cylinder; you should bleed... |
I've vacum-bled VW T1 brakes since the Eighties, no issues. If you get air in lines during process, it's because you let fluid level in reservoir get too low.
bnc _________________ I never found the need to impress people with any mechanic certifications, trophies or track wins... unless it was for Mom to post on the refrigerator door. |
|
Back to top |
|
|
|