Hello! Log in or Register   |  Help  |  Donate  |  Buy Shirts  See all banner ads | Advertise on TheSamba.com  
TheSamba.com
 
What did YOU do to your van today?
Page: Previous  1, 2, 3 ... 547, 548, 549, 550, 551  Next
Jump to:
Forum Index -> Vanagon Share: Facebook Twitter
Reply to topic
Print View
Quick sort: Show newest posts on top | Show oldest posts on top View previous topic :: View next topic  
Author Message
vanis13
Samba Member


Joined: August 15, 2010
Posts: 1158
Location: ABQ NM
vanis13 is offline 

PostPosted: Tue Oct 13, 2020 8:09 pm    Post subject: Re: What did YOU do to your van today? Reply with quote

mcarlson_sb wrote:
vanis13 wrote:

I can, but it would really only work if your pins are the same diameter as mine and at the same (radial) place on the leg. what set up do you have?

Currently we have the stock table that never locks in place, swings into the wall and makes a hole, and makes access to the water tank and storage a pain.

I'm looking for ideas to improve all that and your setup inspired me.

We have a few 3d printers and some skill with modeling.
I was mostly hoping to use your STL as a starting point.

My wife has been enjoying remixing prints for the van.
She just did a custom organizer for the kitchen drawer and is thinking of doing the same for the "spice rack" gutter.


PM me your email and I'll send it to you. can also send you the Fusion 360 file

Notice this is your 3rd poist...welcome! from the stock leg, you would need to install pins to use my solution and also if you want the raised table thing, there is a thread on that with several solutions.

Welcome to the madness!
_________________
83.5 Westy with Subaru 2.5, 4 spd manual, center seat, COLD A/C on 134a!, Winter camp heated with an Espar B4 gasoline furnace

I can send you the capacitor to Fix/prevent Vanagon Syndrome and/or smooth out idle - See here - http://www.thesamba.com/vw/forum/viewtopic.php?p=5445671#5445671
Back to top
View user's profile Send private message Gallery Classifieds Feedback
jlrftype7
Samba Member


Joined: July 24, 2018
Posts: 1856
Location: Chicago
jlrftype7 is offline 

PostPosted: Fri Oct 16, 2020 6:30 am    Post subject: Re: What did YOU do to your van today? Reply with quote

I installed, finally, the GoWesty dash illumination LED bulbs for the Heater Controls, and Rear Heater Switch. I went with the Orange version.
Iíd bought them months ago and just kept forgetting to put them in.

Also went through all my parts and supplies , transferring them out of all the cardboard boxes they had been in, and into new plastic storage boxes that have carrying handles and stack pretty well on top of each other.
This way, I can grab a box and take it to the shop and actually know whatís in the box again. My previous storage was just haphazard and lazy.... Embarassed Embarassed Embarassed

Iíve got another set of LED headlights on the way, should be here today.
They have the Angel Ring and Amber Turn Signal ring feature on them, wanted to try that out since I feel more turn signals on the nose of the Vanagon is better than stock, to catch other drivers eyes who donít always seem to focus on the low mounted stock ones when theyíre flashing . Stop signs are the worst, they seem to assume Iím not turning since they donít see the turn signals for a bit.
With high and low turn signals flashing, maybe Iíll stand out a bit more at an intersection for the turn.
I used to see the same effect on the rear with the low mounted tail lights, especially if the vehicle behind me was tall, but adding the 3rd brake light changed all that for the better.
_________________
'68 Westy- my first VW and vehicle/Bus- long gone.- sold it to a traveling Swiss couple....
'67 Type 3 Fastback, my 2nd car- also long gone
'69 Semi-Auto Stick Shift Beetle, my wife's first car= yep. still long gone....
2017 MINI Coopers, our current DDs
Ď84 Tin Top - Hilga....Auto
Back to top
View user's profile Send private message Gallery Classifieds Feedback
jlrftype7
Samba Member


Joined: July 24, 2018
Posts: 1856
Location: Chicago
jlrftype7 is offline 

PostPosted: Sat Oct 17, 2020 4:44 pm    Post subject: Re: What did YOU do to your van today? Reply with quote

Installed the LED headlights that have the DRL / Angel Ring feature and the Yellow turn signal ring.
A drive at night will be the real test, but a side by side view with my Truck Lite LED headlights shows a dimmer Low Beam out of these new headlights in broad daylight,....... Sad

Oh well, they were cheap as a set.... Razz Razz Razz And I can always reinstall the TruckLite set... Wink
Image may have been reduced in size. Click image to view fullscreen.



Image may have been reduced in size. Click image to view fullscreen.

_________________
'68 Westy- my first VW and vehicle/Bus- long gone.- sold it to a traveling Swiss couple....
'67 Type 3 Fastback, my 2nd car- also long gone
'69 Semi-Auto Stick Shift Beetle, my wife's first car= yep. still long gone....
2017 MINI Coopers, our current DDs
Ď84 Tin Top - Hilga....Auto
Back to top
View user's profile Send private message Gallery Classifieds Feedback
jlrftype7
Samba Member


Joined: July 24, 2018
Posts: 1856
Location: Chicago
jlrftype7 is offline 

PostPosted: Sat Oct 17, 2020 8:30 pm    Post subject: Re: What did YOU do to your van today? Reply with quote

I test drove the headlights tonight . Low beam pattern is dimmer in output than my TruckLites, but the beam shape and color of lighting are okay.
High Beams are very good, far, crisp pattern.
So, theyíre keepers for now. Cool
_________________
'68 Westy- my first VW and vehicle/Bus- long gone.- sold it to a traveling Swiss couple....
'67 Type 3 Fastback, my 2nd car- also long gone
'69 Semi-Auto Stick Shift Beetle, my wife's first car= yep. still long gone....
2017 MINI Coopers, our current DDs
Ď84 Tin Top - Hilga....Auto
Back to top
View user's profile Send private message Gallery Classifieds Feedback
mcarlson_sb
Samba Member


Joined: October 12, 2020
Posts: 31
Location: CA
mcarlson_sb is offline 

PostPosted: Sat Oct 17, 2020 10:33 pm    Post subject: Re: What did YOU do to your van today? Reply with quote

The fuel gague hasn't worked the four years we've owned the van.
We've also had problems with the fuel filter getting clogged up with what looks like rust. So, we finally dropped the tank and did repairs today.

It turns out the inside of the old tank wasn't in as bad of shape as expected.
I don't know if it's worth keeping, giving away or what. But the new one is on so we'll see if it helps.

The fuel gague was just PO stupidity.
At some point the cluster gague must have stopped working. Brilliant surfer dude drilled out a 2 inch hole and put in a cheap replacement. Then proceeded to wire it incorrectly.
Ground went to ground
S went to +12
+12 went to the send unit
Then the other wire of the send unit went straight back to POS on the battery
Evil or Very Mad Shocked Evil or Very Mad

No wonder it always read empty

This is not the worst wiring atrocity PO surfer dude has committed.
We have slowly been cleaning them up as we find them.
At this point we have nearly rewired the whole van.

Oh well.. We have a new Bosch fuel gague wired correctly.
And can finally see when the tank is getting close to empty without having to look at the trip and do math

Cheers,
Matthew
Back to top
View user's profile Send private message Gallery Classifieds Feedback
mcarlson_sb
Samba Member


Joined: October 12, 2020
Posts: 31
Location: CA
mcarlson_sb is offline 

PostPosted: Sat Oct 17, 2020 10:50 pm    Post subject: Re: What did YOU do to your van today? Reply with quote

Also, my wife and I both have a hobby of retro electronics.
I do a lot with early computers. She's into LED art.

We took a look at the film circuit board when we had the cluster out.
My wife wants to design a replacement PCB that can be sent away and fabricated for a few dollars.

She measured the resistors and mapped out the traces this afternoon.
Making a cheap replacement should be fun.
Back to top
View user's profile Send private message Gallery Classifieds Feedback
BCE56
Samba Member


Joined: July 16, 2013
Posts: 101
Location: So Cal
BCE56 is offline 

PostPosted: Sun Oct 18, 2020 10:58 am    Post subject: Re: What did YOU do to your van today? Reply with quote

"My wife wants to design a replacement PCB that can be sent away and fabricated for a few dollars.

She measured the resistors and mapped out the traces this afternoon.
Making a cheap replacement should be fun."

^^ A worthwhile project. I've been keeping an eye on these if the need should arise:

https://www.thesamba.com/vw/classifieds/detail.php?id=2367183
(See link to FB page)

https://www.thesamba.com/vw/classifieds/detail.php?id=1913691
_________________
=BCE56=

'86 Syncro tintop
OBD II Frankenmotor
Early SC adapter plate conversion
SC header, 3-way cat, VW muff.
stock springs, OME shocks*
VC, rear locker**
215-75 BFG AT/TAs on Rhein rims
*OMEs a bit too stiff in front, OK in rear or on heavier vans. Will try Bilsteins. Someday.
**PO installed taller top gear before Subie install. Not recommended.
Back to top
View user's profile Send private message Send e-mail Gallery Classifieds Feedback
shadetreemech
Samba Member


Joined: October 05, 2005
Posts: 615
Location: Claremont, CA
shadetreemech is offline 

PostPosted: Mon Oct 19, 2020 11:46 am    Post subject: Re: What did YOU do to your van today? Reply with quote

Got the replacement windshield installed after encountering a rock on our road trip a coupla weeks ago:

https://www.thesamba.com/vw/forum/viewtopic.php?t=744529&highlight=rubber

The insurance company pointed me to the national franchise, "Replace-Deface". After 3 cancellations and "Bring it in and leave it", I told 'em to take a hike and found a local guy in Ontario, Calif. I bought the seal from VanCafe (RMW), windshield installed while I waited, $205 out the door.

Dan
_________________
'84 GL 1.9
'01 Volvo V70 T5
'88 Westy - "Miss Dorothy"
Back to top
View user's profile Send private message Send e-mail Gallery Classifieds Feedback
leecat
Samba Member


Joined: September 13, 2012
Posts: 265
Location: Regina
leecat is offline 

PostPosted: Mon Oct 19, 2020 12:33 pm    Post subject: Re: What did YOU do to your van today? Reply with quote

We picked up a beautiful as-new ARB side tent from some lovely Sambanistas in our local town...super excited, they've been out of stock forever at GoWesty so a lucky find for us!

Now I just need to finish a van to attach it to.

I got no van to drive, but MAN do I got a massive pile of van parts!!! Smile
Back to top
View user's profile Send private message Gallery Classifieds Feedback
epbiggs
Samba Member


Joined: September 19, 2014
Posts: 155
Location: CO
epbiggs is offline 

PostPosted: Tue Oct 20, 2020 6:02 pm    Post subject: Re: What did YOU do to your van today? Reply with quote

I upgraded my Rocky Mountain Westy swing-away tire carrier with their "switch back upper rack" and the lower shelf. This allowed me to move my spare up higher to allow for the tray. My tray now holds my suitcase generator, two FuelPax 3.5 gallon cans and my tool kit. I still have my Trasharoo "clone" on the spare with a few molle attachment bags. Trying to make the most of the space while keeping everything gas related outside of the van.

Before:
Image may have been reduced in size. Click image to view fullscreen.

After: Note the fading of the "trasharoo"
Image may have been reduced in size. Click image to view fullscreen.

Image may have been reduced in size. Click image to view fullscreen.

Image may have been reduced in size. Click image to view fullscreen.

Image may have been reduced in size. Click image to view fullscreen.

A locking cable goes through the handles of both the generator and tool kit and routes through the Westy cutout of the tray, which allows for the cover to fit over both
Image may have been reduced in size. Click image to view fullscreen.

The generously sized weatherproof generator cover fits over both the generator and tool kit
Image may have been reduced in size. Click image to view fullscreen.

Image may have been reduced in size. Click image to view fullscreen.

Image may have been reduced in size. Click image to view fullscreen.

And a ratchet strap to hold it all in nice and tight, plus a cable and lock for the cans
Image may have been reduced in size. Click image to view fullscreen.

Image may have been reduced in size. Click image to view fullscreen.

Image may have been reduced in size. Click image to view fullscreen.

_________________
EPBiggs
1986 Syncro Westy
Previous:
1983 Westy
1981 Westy
1972 Bug (Last year you could buy a new one for under $2,000)
1965 Bug
1959 Bug
Back to top
View user's profile Send private message Send e-mail Gallery Classifieds Feedback
vanis13
Samba Member


Joined: August 15, 2010
Posts: 1158
Location: ABQ NM
vanis13 is offline 

PostPosted: Tue Oct 20, 2020 10:17 pm    Post subject: Re: What did YOU do to your van today? Reply with quote

epbiggs wrote:
Image may have been reduced in size. Click image to view fullscreen.


What kind of lift assists do you have on your pop-top?
_________________
83.5 Westy with Subaru 2.5, 4 spd manual, center seat, COLD A/C on 134a!, Winter camp heated with an Espar B4 gasoline furnace

I can send you the capacitor to Fix/prevent Vanagon Syndrome and/or smooth out idle - See here - http://www.thesamba.com/vw/forum/viewtopic.php?p=5445671#5445671
Back to top
View user's profile Send private message Gallery Classifieds Feedback
epbiggs
Samba Member


Joined: September 19, 2014
Posts: 155
Location: CO
epbiggs is offline 

PostPosted: Tue Oct 20, 2020 10:54 pm    Post subject: Re: What did YOU do to your van today? Reply with quote

vanis13 wrote:
epbiggs wrote:
Image may have been reduced in size. Click image to view fullscreen.


What kind of lift assists do you have on your pop-top?


Jack Bombay struts in the back and GoWesty HD struts in the front.
_________________
EPBiggs
1986 Syncro Westy
Previous:
1983 Westy
1981 Westy
1972 Bug (Last year you could buy a new one for under $2,000)
1965 Bug
1959 Bug
Back to top
View user's profile Send private message Send e-mail Gallery Classifieds Feedback
mcarlson_sb
Samba Member


Joined: October 12, 2020
Posts: 31
Location: CA
mcarlson_sb is offline 

PostPosted: Wed Oct 21, 2020 8:00 am    Post subject: Re: What did YOU do to your van today? Reply with quote

I'm slowly going around the van and replacing all the seals.
Yesterday was the rear hatch. Easy and fast
Back to top
View user's profile Send private message Gallery Classifieds Feedback
mcarlson_sb
Samba Member


Joined: October 12, 2020
Posts: 31
Location: CA
mcarlson_sb is offline 

PostPosted: Wed Oct 21, 2020 7:31 pm    Post subject: Re: What did YOU do to your van today? Reply with quote

Today was cleaning.

I removed the body panel that covers the sliding door mechanism (possibly for the first time since 1980).
I sprayed out the accumulated gunk with Simple Green, wiped years worth of built up crud off the mechanism and channel, and used a little silicone grease to lube the rail.
The door now slides smoothly.

I finally fixed the windshield wipers (blown fuse)
Then found and filled the windshield wiper fluid (seems like I would have done that at least once in the last four years, but hey - better late than never)
That allowed me to adjust aim of the jets to actually hit the windshield rather spray up in the air like fountains.

Finally I covered the driveway with cardboard and some sacrificial rags then sprayed the engine and transmission with Simple Green and carefully rinsed it with a hose. It's been covered in a thick layer of grime as long as we've owned it.
I've mostly left it alone until now. However, the more time I spend under the van the more I want to avoid chunks of grime falling in my face and mouth.
That, and if there are leaks I want to find and fix them.

I've been trying to do a little each day. We'll see what tomorrow brings.
Back to top
View user's profile Send private message Gallery Classifieds Feedback
jlrftype7
Samba Member


Joined: July 24, 2018
Posts: 1856
Location: Chicago
jlrftype7 is offline 

PostPosted: Wed Oct 21, 2020 8:45 pm    Post subject: Re: What did YOU do to your van today? Reply with quote

Just oil and filter change today. Tomorrow is new turn signal lens for both fronts. I have a crack in the drivers side that started taking out the new bulb socket I installed 2 years ago. Only discovered the corrosion and rust when I needed to tap into the turn signals and park bulb circuit for the new headlights I just installed. So I bought 2 new lens to match , and new sockets since the lens come with the European single bulb set-up.
_________________
'68 Westy- my first VW and vehicle/Bus- long gone.- sold it to a traveling Swiss couple....
'67 Type 3 Fastback, my 2nd car- also long gone
'69 Semi-Auto Stick Shift Beetle, my wife's first car= yep. still long gone....
2017 MINI Coopers, our current DDs
Ď84 Tin Top - Hilga....Auto
Back to top
View user's profile Send private message Gallery Classifieds Feedback
Igeo
Samba Member


Joined: September 25, 2018
Posts: 571
Location: Oakland, CA
Igeo is offline 

PostPosted: Thu Oct 22, 2020 6:53 am    Post subject: Re: What did YOU do to your van today? Reply with quote

mcarlson_sb wrote:
Today was cleaning.......Finally I covered the driveway with cardboard and some sacrificial rags then sprayed the engine and transmission with Simple Green and carefully rinsed it with a hose. It's been covered in a thick layer of grime as long as we've owned it.
I've mostly left it alone until now. However, the more time I spend under the van the more I want to avoid chunks of grime falling in my face and mouth.
That, and if there are leaks I want to find and fix them.

I've been trying to do a little each day. We'll see what tomorrow brings.


How did the simple green treatment work? Lets see the engine!
_________________
1987 Westfalia 2.1 WBX Manual
Back to top
View user's profile Send private message Gallery Classifieds Feedback
mcarlson_sb
Samba Member


Joined: October 12, 2020
Posts: 31
Location: CA
mcarlson_sb is offline 

PostPosted: Thu Oct 22, 2020 1:12 pm    Post subject: Re: What did YOU do to your van today? Reply with quote

Igeo wrote:

How did the simple green treatment work? Lets see the engine!


It's still ugly dirty. It's just less ugly dirty.
I wish I'd taken a before picture - then an after would at least look like I did something
Back to top
View user's profile Send private message Gallery Classifieds Feedback
shagginwagon83
Samba Member


Joined: February 07, 2016
Posts: 2777
Location: VA/TN
shagginwagon83 is offline 

PostPosted: Thu Oct 22, 2020 8:10 pm    Post subject: Re: What did YOU do to your van today? Reply with quote

Cleaned my engine grounds. Upon tightening the transaxle ground cable, I found the hole was stripped. So drilled and tapped it to m10.

In the engine bay one of the small ground cables showed a lot of corrosion. Cut and put an open barrel ring terminal on it.

My 1.9L no longer stalls at idle during cold. Damn why didn't I do this sooner.

Edit: I actually did this like 4 years ago. This time I used dielectric grease
_________________
Brandon
"Jo Ann" - 1983.5 Ivory Westfalia 1.9L 2wd
Back to top
View user's profile Send private message Instagram Gallery Classifieds Feedback
revolution337
Samba Member


Joined: May 23, 2009
Posts: 121
Location: Pennsylvania
revolution337 is offline 

PostPosted: Sat Oct 24, 2020 7:52 am    Post subject: Re: What did YOU do to your van today? Reply with quote

Added some skateboard grip tape to the rear table leg clamp, to help keep it from moving around while driving. Worked out very well, simple, effective. No longer do I need to use Hulk strength to tighten the knob. Laughing

Before:
Image may have been reduced in size. Click image to view fullscreen.


After:
Image may have been reduced in size. Click image to view fullscreen.
Back to top
View user's profile Send private message Gallery Classifieds Feedback
mcarlson_sb
Samba Member


Joined: October 12, 2020
Posts: 31
Location: CA
mcarlson_sb is offline 

PostPosted: Sat Oct 24, 2020 10:25 pm    Post subject: Re: What did YOU do to your van today? Reply with quote

Image may have been reduced in size. Click image to view fullscreen.


New 3d printed drawer sorter. We used the spool of bright green transparent PLA because "what else would you use it for?!?"
This is version 1.0 and the walls are pretty thin. If they end up breaking we'll print it with thicker walls for v2

(older mods that are visible in the picture)
The switches you can see are:
- route solar to either the aux or main battery
- turn on over kitchen led lights
And a homemade battery level indicator for the starter battery.
The stock one on the panel is routed to the aux batteries

I've also installed an inexpensive dash cam.
Since I've been driving around in the van more I've had several times where police run my plates and follow me. Adding a $25 digital dash cam seems like a very reasonable upgrade.

Cheers,
Matthew
Back to top
View user's profile Send private message Gallery Classifieds Feedback
Display posts from previous:   
Reply to topic    Forum Index -> Vanagon All times are Mountain Standard Time/Pacific Daylight Savings Time
Page: Previous  1, 2, 3 ... 547, 548, 549, 550, 551  Next
Jump to:
Page 548 of 551

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum

About | Help! | Advertise | Donate | Premium Membership | Privacy/Terms of Use | Contact Us | Site Map
Copyright © 1996-2020, Everett Barnes. All Rights Reserved.
Not affiliated with or sponsored by Volkswagen of America | Forum powered by phpBB