Author |
Message |
WonkaVan Samba Member
Joined: November 21, 2011 Posts: 36 Location: United States
|
Posted: Wed Nov 23, 2011 2:40 am Post subject: |
|
|
Is replacing this part with a metal one merely just to keep the process simple when changing fuel lines? So you don't have to dive under the car and behind the firewall... |
|
Back to top |
|
|
Timwhy Samba Member
Joined: January 01, 2009 Posts: 4002 Location: Maine
|
Posted: Wed Nov 23, 2011 4:40 am Post subject: |
|
|
WonkaVan wrote: |
Is replacing this part with a metal one merely just to keep the process simple when changing fuel lines? So you don't have to dive under the car and behind the firewall... |
Yes, it would seem so!
If you are doing soup to nuts on the fuel lines, why wouldn't you start at the fuel tank
and move back to the engine compartment, replacing each and every piece of old
fuel line. Pretty sure that the kits come with a grommet to replace that plactic POS.
Or the come with a larger hose for you to put the fuel line through and then through
the vacant hole in the fire wall. _________________ '15 Audi A3 Quattro
'09 VW Tiguan (dead)
'87 VW Westy
'91 Tin Top
'90 Cabby
What the Westy wants the Westy GETS
http://www.thesamba.com/vw/forum/album_search.php?search_author=Timwhy&show_results=summary
http://www.youtube.com/user/TIMWHY2?feature=mhee |
|
Back to top |
|
|
Tooharsh Samba Member
Joined: February 22, 2012 Posts: 92 Location: Waynesboro, PA
|
Posted: Thu Feb 23, 2012 2:35 pm Post subject: |
|
|
Has anyone ever replaced the long run through the firewall with a steel fuel line? Wondering if there is some reason everyone seems to replace with rubber, and then keep replacing in different intervals. Your thoughts? |
|
Back to top |
|
|
dubbified Samba Member
Joined: March 03, 2010 Posts: 1406 Location: Redmond, WA
|
|
Back to top |
|
|
dobryan Samba Member
Joined: March 24, 2006 Posts: 16505 Location: Brookeville, MD
|
|
Back to top |
|
|
SCM Samba Member
Joined: January 26, 2011 Posts: 3119 Location: Bozeman MT
|
Posted: Thu Feb 23, 2012 4:12 pm Post subject: |
|
|
How about the hard plasic line that connects between the fuel filter the firewall fitting? Any reason to keep that vs running one contuous 7mm line from the engine, through the firewall, right up to the fuel filter> _________________ '91 Westfalia GL Automatic (GTA "Turbo" Rebuild w/Peloquin) and 2.3L GoWesty Engine |
|
Back to top |
|
|
vanagonjr Samba Member
Joined: October 07, 2010 Posts: 3431 Location: Dartmouth, Mass.
|
Posted: Thu Feb 23, 2012 4:30 pm Post subject: |
|
|
SCM wrote: |
How about the hard plasic line that connects between the fuel filter the firewall fitting? Any reason to keep that vs running one contuous 7mm line from the engine, through the firewall, right up to the fuel filter> |
Not really - probably there to make installing the engine easier on the assembly line. I used a grommet where it went through the firewall. There is a metal replacement - see a couple of posts ago - but I see no strong reason to have this piece. _________________ John - 86 Wolfsburg Westfalia "Weekender"
Flint reversed 1.8T W/Passat 5-Speed
LiMBO (late model bus club) www.limbobus.org
LiMBO is on Facebook too! https://www.facebook.com/groups/
FAQ thread: http://www.thesamba.com/vw/forum/viewtopic.php?t=525798 |
|
Back to top |
|
|
SCM Samba Member
Joined: January 26, 2011 Posts: 3119 Location: Bozeman MT
|
Posted: Thu Feb 23, 2012 4:42 pm Post subject: |
|
|
vanagonjr wrote: |
I used a grommet where it went through the firewall. There is a metal replacement - see a couple of posts ago - but I see no strong reason to have this piece. |
Yeah, I understand about the piece that passes through the firewall but I'm refering to the plastic line in front of that piece. At least on my 91, there's hose running from the fuel filter to a hard plastic tube. That tube is almost pencil thick and at least a foot long. Then, there is a short section of hose going from that tube to the "firewall pass-through fitting" that I plan to replace with a grommet. But I'm wondering about that longer section - do they go bad too? I never hear people mention that part. _________________ '91 Westfalia GL Automatic (GTA "Turbo" Rebuild w/Peloquin) and 2.3L GoWesty Engine |
|
Back to top |
|
|
Tooharsh Samba Member
Joined: February 22, 2012 Posts: 92 Location: Waynesboro, PA
|
Posted: Thu Feb 23, 2012 7:13 pm Post subject: |
|
|
Bump, anyone use steel fuel lines? |
|
Back to top |
|
|
GreenMachineVW Samba Member
Joined: August 08, 2008 Posts: 645
|
Posted: Thu Feb 23, 2012 7:23 pm Post subject: |
|
|
In the oft criticized air-cooled models, the engine compartment fuel lines are mostly steel, with short rubber pieces to allow for movement instead of breakage. While the short sections are subject to the same deterioration risks as any fuel lines, the short sections are much less prone to rupture. |
|
Back to top |
|
|
Tooharsh Samba Member
Joined: February 22, 2012 Posts: 92 Location: Waynesboro, PA
|
Posted: Fri Feb 24, 2012 3:13 am Post subject: |
|
|
That is what I was thinking. A small say 2" section of hose just before the connection point. That would provide for a little movement, but 95% of the line you would never have to worry about again. |
|
Back to top |
|
|
Jake de Villiers Samba Member
Joined: October 24, 2007 Posts: 5911 Location: Tsawwassen, BC
|
Posted: Fri Feb 24, 2012 2:32 pm Post subject: |
|
|
SCM wrote: |
How about the hard plasic line that connects between the fuel filter the firewall fitting? Any reason to keep that vs running one contuous 7mm line from the engine, through the firewall, right up to the fuel filter> |
No reason at all. When I installed my Subaru engine I went with one-piece FI hose from the pump all the way to the steel fuel lines on the engine.
Comforting. _________________ '84 Vanagon GL 1.9 WBX
'86 Westy Weekender Poptop/2.5 Subaru/5 Speed Posi/Audi Front Brakes/16 x 7 Mercedes Wheels - answers to 'Dixie'
@jakedevilliersmusic1
http://sites.google.com/site/subyjake/mydixiedarlin%27
www.crescentbeachguitar.com
www.thebassspa.com |
|
Back to top |
|
|
ib-bus Samba Member
Joined: September 26, 2007 Posts: 264 Location: Temecula , CA
|
Posted: Mon Aug 20, 2012 10:56 am Post subject: |
|
|
Since I can't find the Goodyear fuel injection hose locally in 5/16 , what do you guys think about this one from NAPA ? seems to be similar to the Goodyear if not better , anybody has used this ?
http://www.napaonline.com/Catalog/CatalogItemDetail.aspx?R=NBHH358_0006447045
There is some good information if you click on the "features and benefits" PDF link.
|
|
Back to top |
|
|
ib-bus Samba Member
Joined: September 26, 2007 Posts: 264 Location: Temecula , CA
|
Posted: Mon Aug 20, 2012 5:36 pm Post subject: |
|
|
I just bought and installed the above hose from NAPA and it's actually made by Gates , it also has the inner lining like Goodyear's and was about $4 per ft. |
|
Back to top |
|
|
AdrianC Samba Member
Joined: January 13, 2012 Posts: 526 Location: Wherever the road's gone
|
Posted: Sat Sep 08, 2012 11:47 am Post subject: |
|
|
I just replaced the short rubber section from plastic pipe from filter to plastic bulkhead mounting - when replacing the coolant tower, I must've nudged it, and the original 1987-date-stamped hose decided that was the last straw. I replaced it with an all-in-one to the metal t-piece to the injector rails.
Bear in mind that, over here in Europe, we don't seem to have anything LIKE the same amount of engine bay fires as you guys - must be different fuel chemistry.
Anyway, the new hose lasted TWO DAYS of running, then split underneath the inlet manifold. Fuel was pouring over the engine, to the point it wouldn't idle smoothly.
I replaced it with new hose, from the car parts store I'd stopped just round the corner from, using the bulkhead joint this time.
That lasted FOUR HOURS. Then the engine cut, half way round a bend. The end of the section from pipe to bulkhead had ballooned and burst. Replaced it again, in the middle of nowhere.
That section was already noticeably soft to to the touch the next morning, so I replaced it with some of the stuff that'd at least lasted a couple of days. That got us to a car parts store where I bought some stuff that was at least marked-up as fuel hose, which got fitted that night.
It's actually possible to change the bit from pipe to engine bay tee, with one caveat... Remove the final pipe-to-body clip before the joint. The pipe seems to be staying in place just fine, but it gives you enough movement that you can pull it all through far enough to do the entire job from the engine bay.
Not, hopefully, that you'll have to do it this often! _________________ Adrian
Zookeeper of a miscellany of motoring silliness, from 0.75bhp to 9ft tall.
Living life on the road in an '88 2.1DJ Westfalia Club Joker Hightop.
www.WhereverTheRoadGoes.com |
|
Back to top |
|
|
|