Author |
Message |
ach60 Samba Member
Joined: May 14, 2001 Posts: 4139 Location: Santa Maria
|
Posted: Fri Aug 23, 2013 12:42 pm Post subject: Took too long to order L3 heads, rats! |
|
|
Long story short: I'm slow.
But I see that L3 heads are on back order, and heard that there are not even castings for L3 heads.
I've been collecting and pre-assembling a 1904 motor based on John's tech articles.
I had not ordered my L3 heads because my mock up was not completed.
I'm using a 74 mm crank,
13# flywheel,
Bus Pressure Plate,
5.325 rods,
90.5 P/C,
Engle 110 cam & Engle lifters,
with stock ratio CB performance rocker arm kit.
1.357 header/ j-tubes / single muffler.
Carbs will be dual 40 IDA's
SO THE QUESTION IS, IF I can't get L3 heads, what heads should I order?
I'd rather not have to buy different parts, because I choose "bigger" heads like L5's.
ADDED NOTE:
John says details on L3 will firm up in the next few weeks,
but I'm still curious about suggested alternates to L3's
Thanks for all your help so far. _________________ Good Luck
Al
Last edited by ach60 on Fri Aug 23, 2013 12:58 pm; edited 1 time in total |
|
Back to top |
|
|
[email protected] Samba Member
Joined: August 03, 2002 Posts: 12785 Location: Salt Lake City, Utah
|
Posted: Fri Aug 23, 2013 12:48 pm Post subject: Re: Took too long to order L3 heads, rats! |
|
|
not really.
The head castings we were using are NLA, so we are changing them.
Until we have the details sorted out, we made them "unavailable" to order.
We'll have them available again to order late next week. When we have all the details, we'll revise the product descriptions and pictures to be accurate, we just didn't want to mislead anyone and have them get something different than they expected.
The ACN L3 is one of our more popular products, it's not going anywhere! _________________ It's just advice, do whatever you want with it!
Please do NOT send me Private Messages through the Samba PM System (I will not see them). Send me an e-mail to john at aircooled dot net
"Like" our Facebook page at
http://www.facebook.com/vwpartsaircoolednet
and get a 5% off code for use on one order for VW Parts ON OUR PARTS STORE WEBSITE, vwparts.aircooled.net |
|
Back to top |
|
|
saw2 Samba Member
Joined: November 06, 2008 Posts: 321 Location: nw Oregon
|
Posted: Fri Aug 23, 2013 3:29 pm Post subject: |
|
|
John
Do the new castings happen to be the Revmaster castings? I have not seen if the Revmaster castings are available with 35.5x32 valve size? |
|
Back to top |
|
|
[email protected] Samba Member
Joined: August 03, 2002 Posts: 12785 Location: Salt Lake City, Utah
|
Posted: Fri Aug 23, 2013 3:35 pm Post subject: |
|
|
049 Revmaster are the basis of our L5, L6, and L7s, but they do not do a 35 x 32mm. _________________ It's just advice, do whatever you want with it!
Please do NOT send me Private Messages through the Samba PM System (I will not see them). Send me an e-mail to john at aircooled dot net
"Like" our Facebook page at
http://www.facebook.com/vwpartsaircoolednet
and get a 5% off code for use on one order for VW Parts ON OUR PARTS STORE WEBSITE, vwparts.aircooled.net |
|
Back to top |
|
|
barfy Samba Member
Joined: August 16, 2009 Posts: 167 Location: somewhere
|
Posted: Fri Aug 23, 2013 4:55 pm Post subject: |
|
|
You could always get Mofoco heads or Steve Tims |
|
Back to top |
|
|
AlteWagen Troll
Joined: February 23, 2007 Posts: 8503 Location: PNW
|
Posted: Fri Aug 23, 2013 5:18 pm Post subject: |
|
|
If in a hurry I would just order a set of CB Bandito heads. Yes they have 40x35 valves but they are build on genuine VW 043 castings and have stock ports. If a bit larger port is wanted the 049 40x35 non ported head would do just fine as well. |
|
Back to top |
|
|
skills@eurocarsplus Samba Peckerhead
Joined: January 01, 2007 Posts: 16879 Location: sticksville, ct.
|
Posted: Fri Aug 23, 2013 7:22 pm Post subject: |
|
|
i would hold out for the L3's....i like them. the stainless valves are a bit 'loud' but the work is real nice on them.
john won't do you wrong! _________________
gprudenciop wrote: |
my reason for switching to subaru is my german car was turning chinese so i said fuck it and went japanese....... |
Jake Raby wrote: |
Thanks for the correction. I used to be a nice guy, then I ruined it by exposing myself to the public. |
Brian wrote: |
Also the fact that people are agreeing with Skills, it's a turn of events for samba history |
|
|
Back to top |
|
|
|