Author |
Message |
ateneo Samba Member
Joined: June 12, 2008 Posts: 403 Location: Orange County, California
|
Posted: Mon Apr 14, 2014 8:49 pm Post subject: My restoration project, a 1971 Westfalia. Still learning. |
|
|
April 7, 2014
Last Saturday, I finally had the courage to overcome my fears of doing body work on my 1971 VW Westfalia bus. Oh wait, I think I need to introduce my project first and give a brief history of how I ended up owning it.
I think it was 2 ½ years ago when I spotted a 1971 Westfalia being sold in the internet. I spoke to the owner over the phone and asked her about the history of her Westy. She told me that it was owned by her son-in-law for many years and it has traveled around the U.S. It had stayed in places like New Jersey, Alaska, California, etc. While it was in the state of Louisiana, its engine broke down. The son-in-law decided to just give it to his mother-in-law who was a traveling chef. The mother-in-law was thrilled to own a Westy and decided to spend money to have a rebuilt DP 1600 engine installed in it.
With the bus having a new engine, the lady owner felt delighted that the doors to travel opened before her. She was offered a part-time chef job in Los Angeles and so she decided to pack up and relocate to California. She drove the bus from Louisiana to California (1900 miles) without a problem. When she reached Los Angeles, one of her grand children accidentally kicked the transmission shift lever and it became lose. The lady felt so bad that she just spent money on her bus and now she is unable to change gears. Exasperated, she decided to sell the bus in the internet.
After contacted the owner over the phone, I decided to check out the bus. After inspecting the Westy, I discovered that the wood interior is undamaged and is mostly original. The pop-top canvas is pretty much tattered and needs to be replaced. The grills on the roof where baggage are placed also need to be repainted. But the roof is in good condition. One of the roof hinges is broken and needs to be replaced. The floor in the back area is fine but some parts of the floor in the front area needs repair. The rocker on the right side needs a little repair but the rocker on the left side has been eaten away by rust, specially the one near the right wheel well. The owner said that the rust started when the bus was in Alaska. The dog legs on both sides are also bad and the body area behind the front wheels has been eaten by rust. The battery tray is rusted out and the replacement one that was placed in it has been eaten away by rust as well.
I can tell that the owner just wants to walk away from the bus. I was a bit worried that the bus might just end up in a salvage yard. I don’t know much about doing body work but the bus seemed to be asking me to save it from a certain death. Normally I would immediately walk away from this type of bus because it just requires too much expensive body work. But I felt bad walking away from this Westy because I know it will just end up as a donor vehicle where it will be chopped into many pieces to patch up other Westies out there. The business side of me is loudly warning me that I am about to make a humongous mistake and a loud speaker in my mind is barking “It’s a money pit!!!”…but the compassionate side of me is telling me that this Westy needs to live on and drive the roads of America. It has traveled to many parts of United States and it deserves to continue its journey.
I thought to myself, “I know this is a dumb & stupid decision but I am entitled to a dumb decision once in a while and today is that day! Besides, I will never know what I am capable of doing if I don’t try”. Please note, when I bought the Westy, it wasn’t April 1st.
So, negotiation time! After I pointed the long list of expensive restoration work that is needed to be done on the bus plus the ever present “unknowns” that always pops out during restoration, the lady owner decided to sell me the Westy at a very affordable price. I figured that if everything does not work well, I can always sell the engine and get my money back.
After paying the lady, she offered to have the Westy towed to my place for just $70 using her friend’s AAA membership that has a 100-mile towing service. I took the offer because it would cost me much more if I call a regular towing company to do it.
After the Westy was placed on the driveway of my house, I crawled underneath the bus to check what went wrong with the gear shifter. After looking around, I discovered that the screw on the coupler came off that is why the shifter is no longer working. I screwed it back and test drove the bus.
For the next few months, I used the Westy to drive to San Diego, areas in San Bernandino and the beach. Once in a while, I would drive it to work but my colleagues are afraid to park next to me worried that their new shiny cars might get infected by the rust in my Westy.
I checked around on how much it would cost to have the rust repaired on my Westy. The estimates I got were just outrageous. Even though I know there are welding guys out there whom I can hire, I felt that I should be the one who should do the rust repairs. There is one problem, I don’t know how to weld. The solution? It’s the perfect time to study welding!
I bought myself a new Lincoln 140 MIG welding machine and decided to self-study. I had to do a lot of trial and error practicing on different gauges of sheet metal from 20 gauge through 16 gauge. There was one time when I was at Bill & Steves buying parts when I saw a guy who was about to throw away a front hood that came off of his 1969 bug that has slightly damage. I asked the guy if I can have the hood because I have been looking for VW body parts that I can use to practice my welding. He did not have a problem giving the hood to me.
For months, I practiced butt welding off and on during weekends. Not having someone to teach me how to weld is kind of frustrating because I can only rely on the internet whenever I am not getting good results on my welding. YouTube seems to be the most valuable resource of information on welding tutorials.
Let me tell you, if I have to do it all over again, I would rather just enroll in a college course that offers welding classes at night or during the weekends. Why didn’t I do it in the first place? Ever wonder why the men don’t like to ask for direction? This common male behavior kicked in during my quest to learn how to weld. That was a dumb move? Well, I already did a dumb thing by buying this rust bucket Westy, so why stop now.
The first areas that I will be working on in the Westy have 18 & 20 gauge metals. Here’s my plan—I will work first on the easy areas to restore and work myself towards the harder areas. Last Saturday, I decided to tackle the battery tray. After looking at it closely, I discovered that when the battery tray rusted out, the previous owner just had a replacement placed on top of it and was just screwed in by two bolts. The short splash shield (whatever you call that short metal shield behind the rear wheels) was pulled upward by the person who installed the replacement battery tray. Whoever did the battery tray was a butcher who did not really care much for the VW bus. I removed the bolts and out came the rusty tray. Now the hard part starts, I need to remove the original tray… or what is left of it.
I am aware that one of the best tool to use in this situation is a spot weld removal bit. Unfortunately, I don’t have one and did not really feel like searching for one at hardware stores at that time. Using an angle grinder with a 4-inch cutting disc, I decided to cut the edges of the old tray just enough so that I could pry & snap them off from their spot welds. Some of the cut pieces came off easily but some were a bit stubborn. The lower rear corner area near the right tail light has a lot of bondo and this tells me that there is a rust hole in there. When I pulled the edge of the tray that ran in that area, the wall crumbled and all of a sudden I could see the sky through the rusted hole that is shaped like a smile. The restoration just became more interesting.
[/b][/i] |
|
Back to top |
|
|
Lionhart94010 Samba Member
Joined: January 04, 2005 Posts: 1417 Location: SF Bay Area / Silicon Valley / So Cal
|
Posted: Mon Apr 14, 2014 10:08 pm Post subject: |
|
|
Good luck with your restoration…
You may want to look into using a football to repair the front of your bus :0)
http://www.youtube.com/watch?v=DQVre6S5J60 seems to work quit well! _________________ Current VWs 71 T2 Westy SO-72/6(Miami), 71 Crew Cab, 2015 GSW TDI
Other owned VW’s 59, 68 1500s, 69 & 71 Bug’s; 72 & 73 S-Bug’s; 67 Westy, 67 Deluxe, Other 71 DC, 72 KG GT that now lives in Australia, 12 JSW TDI, 2015 GSW TDI, 2023 Tiguan
VW technical information sights
thesamba - www.ratwell.com - www.shoptalkforums.com/ - www.vw-resource.com - http://www.type2.com/
http://bobhooversblog.blogspot.com/ - www.aircooled.net/gnrlsite/resource/articles.htm |
|
Back to top |
|
|
Danwvw Samba Member
Joined: July 31, 2012 Posts: 8892 Location: Oregon Coast
|
Posted: Mon Apr 14, 2014 10:24 pm Post subject: |
|
|
Very neat to read your Bus story! I have thought about taking up welding for the same reasons. Will be following your progress! _________________ 1960 Beetle And 1679cc DP W-100 & Dual Zeniths!
Last edited by Danwvw on Tue Apr 15, 2014 10:34 am; edited 1 time in total |
|
Back to top |
|
|
seventyfo Samba Member
Joined: February 13, 2007 Posts: 916 Location: Ocoee FL
|
Posted: Tue Apr 15, 2014 7:36 am Post subject: |
|
|
I don't know, I looked at all the pictures and I still don't see the rusty part. Awesome bus! _________________ 85 Vanagon GL Westy GW 2.2 (Rebuilt by YT)
"I don't know you well enough to care about your comments". Watkins Cravey |
|
Back to top |
|
|
Bala Samba Member
Joined: December 04, 2003 Posts: 2613 Location: Austin, TX
|
Posted: Tue Apr 15, 2014 7:47 am Post subject: |
|
|
Welcome, great first post! _________________ 1976 Westy
1966 Beetle |
|
Back to top |
|
|
Marleybus Samba Member
Joined: January 05, 2013 Posts: 314 Location: Oro Station, Ontario, Canada
|
Posted: Tue Apr 15, 2014 8:48 am Post subject: |
|
|
Good Luck. Sounds like the bus is part of the family already!!! _________________ 1972 VW Westy (Hit by dumptruck)
1963 VW Beetle (RIP)
1974 VW Beetle (RIP)
1981 Vanagon Westfalia (Sold)
1969 VW Beetle Convertible (Wifes)
1977 VW Westy 2.0L FI Chrome Yellow
1978 VW Westy 2.0L FI (Under Restoration)
1973 VW Westy 1.7L Tourist Delivery Orange
Check out my thread!!http://www.thesamba.com/vw/forum/viewtopic.php?t=556709 |
|
Back to top |
|
|
ateneo Samba Member
Joined: June 12, 2008 Posts: 403 Location: Orange County, California
|
Posted: Tue Apr 15, 2014 5:46 pm Post subject: |
|
|
April 11, 2014
It was my day off yesterday and so I decided to remove the remaining edges of the old rusty battery pan. Instead of just prying off the pieces of the edges of the pan, I decided to locate the spot welds and grind them using my electric cutoff tool. This way I can easily pry off the pieces easier instead of struggling to ripping off the welds off of the edges of the pan using an angled nose pliers.
After I did some adjustments, I was able to fit the replacement battery pan. It still needs adjustments here and there but at least I know that the new part will fit. I am thinking of buying clecos because I have seen lots of restorers use them.
|
|
Back to top |
|
|
bgoble Samba Member
Joined: February 26, 2011 Posts: 34 Location: North AL
|
Posted: Tue Apr 15, 2014 6:09 pm Post subject: |
|
|
Check out this thread of the rust repair on my bus. I had rust in some of the same places as you. There are some detailed pics and tips that may help.
Sorry about the multiple posts. I don't know how the delete the duplicates.
http://www.thesamba.com/vw/forum/viewtopic.php?t=543445&highlight=
Last edited by bgoble on Tue Apr 15, 2014 6:34 pm; edited 1 time in total |
|
Back to top |
|
|
bgoble Samba Member
Joined: February 26, 2011 Posts: 34 Location: North AL
|
|
Back to top |
|
|
bgoble Samba Member
Joined: February 26, 2011 Posts: 34 Location: North AL
|
|
Back to top |
|
|
ateneo Samba Member
Joined: June 12, 2008 Posts: 403 Location: Orange County, California
|
Posted: Tue Apr 15, 2014 6:11 pm Post subject: |
|
|
|
|
Back to top |
|
|
ateneo Samba Member
Joined: June 12, 2008 Posts: 403 Location: Orange County, California
|
Posted: Wed Apr 16, 2014 6:34 am Post subject: |
|
|
I wil definitely do that Thanks |
|
Back to top |
|
|
ateneo Samba Member
Joined: June 12, 2008 Posts: 403 Location: Orange County, California
|
Posted: Wed Apr 16, 2014 6:40 am Post subject: |
|
|
Danwvw wrote: |
Very neat to read your Bus story! I have thought about taking up welding for the same reasons. Will be following your progress! |
After learning a little bit on butt welding, I did not feel worried anymore whenever I see a rust spot on my VWs. I am even thinking of doing some welding on my fence. |
|
Back to top |
|
|
ateneo Samba Member
Joined: June 12, 2008 Posts: 403 Location: Orange County, California
|
Posted: Wed Apr 16, 2014 6:42 am Post subject: |
|
|
seventyfo wrote: |
I don't know, I looked at all the pictures and I still don't see the rusty part. Awesome bus! |
I am going to be posting more pictures very soon. This bus is rust paradise. |
|
Back to top |
|
|
ateneo Samba Member
Joined: June 12, 2008 Posts: 403 Location: Orange County, California
|
Posted: Wed Apr 16, 2014 6:43 am Post subject: |
|
|
Bala wrote: |
Welcome, great first post! |
Thank you |
|
Back to top |
|
|
ateneo Samba Member
Joined: June 12, 2008 Posts: 403 Location: Orange County, California
|
Posted: Wed Apr 16, 2014 6:46 am Post subject: |
|
|
Marleybus wrote: |
Good Luck. Sounds like the bus is part of the family already!!! |
The wife and kids does not like to ride it yet unless the rust is out. The wife is afraid that our kids might get tetanus. |
|
Back to top |
|
|
ateneo Samba Member
Joined: June 12, 2008 Posts: 403 Location: Orange County, California
|
Posted: Wed Apr 16, 2014 6:49 am Post subject: |
|
|
Thanks for this tip. That guy is a whiz on welding…I wish he could give classes to amateur welders like myself. |
|
Back to top |
|
|
1967250s Samba Member
Joined: May 02, 2007 Posts: 2137
|
Posted: Wed Apr 16, 2014 1:22 pm Post subject: |
|
|
Between youtube welding videos and wrstp's threads you have it covered! Go for it! |
|
Back to top |
|
|
Tcash Samba Member
Joined: July 20, 2011 Posts: 12844 Location: San Jose, California, USA
|
Posted: Wed Apr 16, 2014 2:00 pm Post subject: |
|
|
Nice find.
|
|
Back to top |
|
|
ateneo Samba Member
Joined: June 12, 2008 Posts: 403 Location: Orange County, California
|
Posted: Wed Apr 16, 2014 2:12 pm Post subject: |
|
|
Hi Tcash. Thanks for the info. I will need all the tips that I can get out there in the net. This restoration is beginning to become tougher as I progress through it. YOu will see more pictures of the horrors that faces me on this project. |
|
Back to top |
|
|
|