Author |
Message |
Christoffer Samba Member
Joined: October 08, 2013 Posts: 8
|
Posted: Sun Mar 19, 2017 11:26 am Post subject: 1967 voltage regulator burning hot |
|
|
Hi,
I bought for my 6V 1967 Beetle a new factory rebuilt generator and at the same time a new regulator (made in USA).
I have polarised the generator, check all connections and all seems fine. The car runs but after one minute the regulator (back side) heats up so much that you can't touch it without burning your finger.
Any ideas what is wrong?
According the dealer the new regulator has to be tuned in to suit the new generator, is this correct or i he pulling my leg?
At idle i measured the voltage on the battery to 7.3V
Christoffer |
|
Back to top |
|
|
67rustavenger Samba Member
Joined: February 24, 2015 Posts: 9756 Location: Oregon
|
Posted: Sun Mar 19, 2017 11:31 am Post subject: Re: 1967 voltage regulator burning hot |
|
|
Say what? Never heard of "tuning" a regulator. If I'm wrong I'll get corrected shortly. That sound's bizarre. _________________ I have learned over the years.
Cheap parts are gonna disappoint you.
Buy Once, Cry Once!
There's never enough time to do it right the first time. But there's always enough time to do it thrice.
GFY's Xevin and VW_Jimbo! |
|
Back to top |
|
|
Cusser Samba Member
Joined: October 02, 2006 Posts: 31361 Location: Hot Arizona
|
Posted: Sun Mar 19, 2017 12:36 pm Post subject: Re: 1967 voltage regulator burning hot |
|
|
Christoffer wrote: |
I bought for my 6V 1967 Beetle a new factory rebuilt generator and at the same time a new regulator (made in USA). I have polarised the generator, check all connections and all seems fine. The car runs but after one minute the regulator (back side) heats up so much that you can't touch it without burning your finger. |
OK, 1967 with 6-volt system; so you must be out of USA or a non-USA model. Your running voltage of 7.3 sounds OK, maybe just at the high end of the charging range. I assume the 6 volt VR is mounted on top of your generator.
My own 1970 (12 volt) had its original factory voltage regulator with its generator, and it got hot relatively quickly as well (and charging light came on after about 10 minutes of driving), can't say if that was within one minute of driving though; that VR sounds too hot to "be OK". I bought a Bosch solid state replacement for mine, fixed it. _________________ 1970 VW (owned since 1972) and 1971 VW Convertible (owned since 1976), second owner of each. The '71 now has the 1835 engine, swapped from the '70. Second owner of each. 1988 Mazda B2200 truck, 1998 Frontier, 2014 Yukon, 2004 Frontier King Cab. All manual transmission except for the Yukon. http://www.thesamba.com/vw/forum/album_page.php?pic_id=335294 http://www.thesamba.com/vw/forum/album_page.php?pic_id=335297 |
|
Back to top |
|
|
Christoffer Samba Member
Joined: October 08, 2013 Posts: 8
|
Posted: Sun Mar 19, 2017 1:31 pm Post subject: Re: 1967 voltage regulator burning hot |
|
|
Cusser wrote: |
Christoffer wrote: |
I bought for my 6V 1967 Beetle a new factory rebuilt generator and at the same time a new regulator (made in USA). I have polarised the generator, check all connections and all seems fine. The car runs but after one minute the regulator (back side) heats up so much that you can't touch it without burning your finger. |
OK, 1967 with 6-volt system; so you must be out of USA or a non-USA model. Your running voltage of 7.3 sounds OK, maybe just at the high end of the charging range. I assume the 6 volt VR is mounted on top of your generator.
My own 1970 (12 volt) had its original factory voltage regulator with its generator, and it got hot relatively quickly as well (and charging light came on after about 10 minutes of driving), can't say if that was within one minute of driving though; that VR sounds too hot to "be OK". I bought a Bosch solid state replacement for mine, fixed it. |
Yes, the car is european but the regulator is located under the rear seat. |
|
Back to top |
|
|
bluebus86 Banned
Joined: September 02, 2010 Posts: 11075
|
Posted: Sun Mar 19, 2017 3:39 pm Post subject: Re: 1967 voltage regulator burning hot |
|
|
Christoffer wrote: |
Cusser wrote: |
Christoffer wrote: |
I bought for my 6V 1967 Beetle a new factory rebuilt generator and at the same time a new regulator (made in USA). I have polarised the generator, check all connections and all seems fine. The car runs but after one minute the regulator (back side) heats up so much that you can't touch it without burning your finger. |
OK, 1967 with 6-volt system; so you must be out of USA or a non-USA model. Your running voltage of 7.3 sounds OK, maybe just at the high end of the charging range. I assume the 6 volt VR is mounted on top of your generator.
My own 1970 (12 volt) had its original factory voltage regulator with its generator, and it got hot relatively quickly as well (and charging light came on after about 10 minutes of driving), can't say if that was within one minute of driving though; that VR sounds too hot to "be OK". I bought a Bosch solid state replacement for mine, fixed it. |
Yes, the car is european but the regulator is located under the rear seat. |
The official service manual has some basic test procedures you could perform on charging system, ALSO....... Make sure everthing is wired correct, good clean tight conections. Also you could unscrew the regulator lid or cover, (First disconnected from battery!) and look for what might be showing signs of heat damage, burnt points, arcing, etc..... does any particular input/output wire on the regulator also get hot not near the hot regulator, but also further away (ie is wire also self heating hot, and if so, which wire(s).)
Screw on lid is in center of the lid, and maybe hidden under a dot of thick paint or sealer. Although not so needed in the under seat mounting location, This paint dot is needed on the generator mounted regulators in Bugs , With the screw then on top of the regulator, that screw if not sealed may leak water in rain, washing of car. I once had a nice newish looking regulator in my box of regulators, this, the cleanist looking one did not work, removed cover and found it all rusty. even just a few drops of water, and you may have weeks and more or 100% humidity, basically a sauna enviroment.
So reseal that screw if mounted where it might possibly get wet.
good luck _________________ Help Prevent VW Engine Fires, see this link.....Engine safety wire information
Stop introducing dirt into your oil when adjusting valves ... https://www.thesamba.com/vw/forum/viewtopic.php?t=683022 |
|
Back to top |
|
|
Christoffer Samba Member
Joined: October 08, 2013 Posts: 8
|
Posted: Thu Mar 23, 2017 12:06 pm Post subject: Re: 1967 voltage regulator burning hot |
|
|
So did some test today and found when engine running 6.9-7 volts on the battery, 17 volts output from the generator. When the engine was running it is the DF connection on the regulator that heats up. Any ideas what could cause this?
Christoffer |
|
Back to top |
|
|
sjbartnik Samba Member
Joined: September 01, 2011 Posts: 5994 Location: Brooklyn
|
Posted: Thu Mar 23, 2017 1:12 pm Post subject: Re: 1967 voltage regulator burning hot |
|
|
Need more information, where are you measuring the 17v?
Double check to make sure you have your regulator hooked up properly.
DF on the regulator should be connected to DF on the generator. This is current to the field coils in the generator. The regulator modulates the current to the field coils in order to limit the output of the generator.
It sounds like your regulator is "full-fielding" your generator which is very bad. That will burn out the generator in short order if that's the case.
When the engine is running the voltage reading at D+ on the regulator (which is connected to D+ on the generator) should be very close to the reading at B+ on the regulator (which connects to battery positive terminal, hence B+).
If you are telling me you're getting 17v on D+ while you're getting 7v on B+ then the problem would seem to lie within the regulator itself. It's limiting the system voltage on the output side but it's not modulating DF properly to limit the generator output.
Also make sure the regulator has a good ground, if it's not grounded properly that may be the problem. Is it an electronic solid state regulator or the original electro-mechanical type? _________________ 1965 Volkswagen 1500 Variant S
2000 Kawasaki W650 |
|
Back to top |
|
|
Christoffer Samba Member
Joined: October 08, 2013 Posts: 8
|
Posted: Thu Mar 23, 2017 2:12 pm Post subject: Re: 1967 voltage regulator burning hot |
|
|
I measured 17v directly from the generator by using a jump wire from DF to ground and hooked up a multimeter from ground to D+ on the generator.
I haven't measured D+ or B+on the regulator, will try the tomorrow. Thanks for the tip.
I have a 6v car so isnīt 7v on B+ normal?
Christoffer |
|
Back to top |
|
|
sjbartnik Samba Member
Joined: September 01, 2011 Posts: 5994 Location: Brooklyn
|
Posted: Thu Mar 23, 2017 2:17 pm Post subject: Re: 1967 voltage regulator burning hot |
|
|
Christoffer wrote: |
I measured 17v directly from the generator by using a jump wire from DF to ground and hooked up a multimeter from ground to D+ on the generator. |
Ah OK. That's an important detail!
So yeah that's normal, you basically full-fielded it - that gives you unregulated generator output which you can use to test if the generator is functioning but don't do it for more than a few seconds as you can kill the generator that way.
In that case you can disregard most of my post; it wasn't clear to me that your 17v figure came from a full field test
Quote: |
I haven't measured D+ or B+on the regulator, will try the tomorrow. Thanks for the tip. |
B+ should be the same as whatever you measure directly at the battery since it's a wire that connects directly from there to the battery.
Quote: |
I have a 6v car so isnīt 7v on B+ normal? |
Yes, when the generator is off idle and at operating speed you should see about 7.2-7.5v at the battery. You will likely get less at idle, the generator doesn't really do much at idle.
What kind of regulator are you using? I think we still haven't gotten that answer. _________________ 1965 Volkswagen 1500 Variant S
2000 Kawasaki W650 |
|
Back to top |
|
|
Starbucket Samba Member
Joined: April 30, 2007 Posts: 4025 Location: WA
|
Posted: Thu Mar 23, 2017 2:27 pm Post subject: Re: 1967 voltage regulator burning hot |
|
|
Bet it was made in china. Problem solved. |
|
Back to top |
|
|
Christoffer Samba Member
Joined: October 08, 2013 Posts: 8
|
Posted: Thu Mar 23, 2017 2:28 pm Post subject: Re: 1967 voltage regulator burning hot |
|
|
The regulator is new, the only detail i can give you is that it is made in USA.
Looks like this: https://goo.gl/images/rnxbbl |
|
Back to top |
|
|
Starbucket Samba Member
Joined: April 30, 2007 Posts: 4025 Location: WA
|
Posted: Thu Mar 23, 2017 2:35 pm Post subject: Re: 1967 voltage regulator burning hot |
|
|
Christoffer wrote: |
The regulator is new, the only detail i can give you is that it is made in USA.
Looks like this: https://goo.gl/images/rnxbbl
|
If you bent the mounting legs to mount flat make sure you have plenty of clearance from the connections. |
|
Back to top |
|
|
sjbartnik Samba Member
Joined: September 01, 2011 Posts: 5994 Location: Brooklyn
|
Posted: Thu Mar 23, 2017 2:49 pm Post subject: Re: 1967 voltage regulator burning hot |
|
|
Hmmm that no-name regulator looks highly dubious. Bosch or GTFO.
6v ones are hard to find these days but you can sometimes find them in the classifieds.
If I were you I would find a dead one and install one of the Clover Systems electronic MOSFET regulators into it.
That's what I'm running. _________________ 1965 Volkswagen 1500 Variant S
2000 Kawasaki W650 |
|
Back to top |
|
|
Starbucket Samba Member
Joined: April 30, 2007 Posts: 4025 Location: WA
|
Posted: Thu Mar 23, 2017 3:45 pm Post subject: Re: 1967 voltage regulator burning hot |
|
|
sjbartnik wrote: |
Hmmm that no-name regulator looks highly dubious. Bosch or GTFO.
6v ones are hard to find these days but you can sometimes find them in the classifieds.
If I were you I would find a dead one and install one of the Clover Systems electronic MOSFET regulators into it.
That's what I'm running.
|
Rockauto.com has 3 different manufactures to chose from $28-44. |
|
Back to top |
|
|
sjbartnik Samba Member
Joined: September 01, 2011 Posts: 5994 Location: Brooklyn
|
Posted: Thu Mar 23, 2017 4:11 pm Post subject: Re: 1967 voltage regulator burning hot |
|
|
That said it appears to be regulating voltage properly.
I just don't understand why it's getting so hot. It should get warm but it should not get that hot _________________ 1965 Volkswagen 1500 Variant S
2000 Kawasaki W650 |
|
Back to top |
|
|
sjbartnik Samba Member
Joined: September 01, 2011 Posts: 5994 Location: Brooklyn
|
Posted: Thu Mar 23, 2017 4:13 pm Post subject: Re: 1967 voltage regulator burning hot |
|
|
Starbucket wrote: |
Rockauto.com has 3 different manufactures to chose from $28-44. |
Ha all the units look the exact same in the pics. I suspect there's only one company making those and all those brands are selling under their name.
And they also look the same as the one OP has. _________________ 1965 Volkswagen 1500 Variant S
2000 Kawasaki W650 |
|
Back to top |
|
|
Christoffer Samba Member
Joined: October 08, 2013 Posts: 8
|
Posted: Fri Mar 24, 2017 1:49 am Post subject: Re: 1967 voltage regulator burning hot |
|
|
Thanks for all the replies.
Just to be clear it is not the whole unit that heats up, it is the back/bottom of the unit that heats up, the connection point for the DF wire. |
|
Back to top |
|
|
Starbucket Samba Member
Joined: April 30, 2007 Posts: 4025 Location: WA
|
Posted: Fri Mar 24, 2017 7:21 am Post subject: Re: 1967 voltage regulator burning hot |
|
|
Does the DF wire get hot? What about the other wires, if you find a wire that is getting hot you need to trace it to find where its grounding or just return the reg. and try a new one. |
|
Back to top |
|
|
bluebus86 Banned
Joined: September 02, 2010 Posts: 11075
|
Posted: Fri Mar 24, 2017 8:24 am Post subject: Re: 1967 voltage regulator burning hot |
|
|
did you remove the cover to see if the points are arced or damaged, or any other signs of over heating, burning?
also if only one connection is getting hot, perhaps it is a highresistance problem, maybe a new connectors is needed or wire or terminal needs to be cleaned, or check internally for connection issues as that may cause an over heat.
good luck _________________ Help Prevent VW Engine Fires, see this link.....Engine safety wire information
Stop introducing dirt into your oil when adjusting valves ... https://www.thesamba.com/vw/forum/viewtopic.php?t=683022 |
|
Back to top |
|
|
Christoffer Samba Member
Joined: October 08, 2013 Posts: 8
|
Posted: Fri Mar 24, 2017 11:41 am Post subject: Re: 1967 voltage regulator burning hot |
|
|
Opened up the unit today and it looked to be ok, no arcing, no loose parts etc..
Tried to have headlights on when the car was running to see if that made a differens, still got hot.
In the picture the part circled in red measured 150 celsius according to my infrared thermometer.
The DF wire does not heat up, or any other. |
|
Back to top |
|
|
|