Hello! Log in or Register   |  Help  |  Donate  |  Buy Shirts  See all banner ads | Advertise on TheSamba.com  
TheSamba.com
 
Sealing the nose cone (with steel plate)?
Page: Previous  1, 2
Forum Index -> Bay Window Bus Share: Facebook Twitter
Reply to topic
Print View
Quick sort: Show newest posts on top | Show oldest posts on top View previous topic :: View next topic  
Author Message
ivwshane
Samba Member


Joined: May 19, 2011
Posts: 947
Location: Sacramento ca
ivwshane is offline 

PostPosted: Fri Jul 06, 2018 8:42 pm    Post subject: Re: Sealing the nose cone (with steel plate)? Reply with quote

Well, being the noob that I am, I have no idea of I did it right but I counted ~5.75:1.

I wasn't able to rotate the selector shaft but I was able to pull it out. I'm not sure how much force is required to rotate it but pliers didn't help. When I put the nose cone back on I made sure all the selector keys were the same height (so it should have been in neutral, right).


I also measured the bellhousing from the base to the starter flange and it measured 3 1/4" which should mean I have a 091 bellhousing and therefore a larger 228mm flywheel and the longer starter, correct?
_________________
77 westy 2.0 FI? (who knows)
71 ghia coup 1600dp
Back to top
View user's profile Send private message Gallery Classifieds Feedback
ivwshane
Samba Member


Joined: May 19, 2011
Posts: 947
Location: Sacramento ca
ivwshane is offline 

PostPosted: Fri Jul 06, 2018 8:49 pm    Post subject: Re: Sealing the nose cone (with steel plate)? Reply with quote

SGKent wrote:
Shane - the case on an 091 is better than the 002. If your 002 works then you can sell it after you find an 091. The best place to have a 091 rebuilt is Eric at Transworks in El Cajon CA, down near AeroMech. That comes from Rick Long when he retired. 091 come up for sale all the time - you just won't know what condition they are in until you either run it or someone like Eric takes it apart. There is one in Elverta in CL right now. Offer the guy $450 and see if he will take that or $100 more since he can't guarantee it works. Lots of sandrail folks buy them. https://sacramento.craigslist.org/pts/d/vw-busrib-transmission/6631355808.html



I saw that ad, it looks like it's already dropped $50.

Is this the same place? The website says prices haven't been updated since 2007 and it lists the rebuild price of $400 which seems ridiculously cheap.

http://www.transworks.biz/rebuilt.html
_________________
77 westy 2.0 FI? (who knows)
71 ghia coup 1600dp
Back to top
View user's profile Send private message Gallery Classifieds Feedback
Tcash
Samba Member


Joined: July 20, 2011
Posts: 12846
Location: San Jose, California, USA
Tcash is online now 

PostPosted: Fri Jul 06, 2018 9:06 pm    Post subject: Re: Sealing the nose cone (with steel plate)? Reply with quote

I wasn't able to rotate the selector shaft but I was able to pull it out.
In the Neutral position you should be able to rotate the shaft without too much effort. You may need vise grips to hold the shift lever.
Make sure you can rotate it before you put the tranny in.

When I put the nose cone back on I made sure all the selector keys were the same height (so it should have been in neutral, right).
That would be Neutral.

I also measured the bellhousing from the base to the starter flange and it measured 3 1/4" which should mean I have a 091 bellhousing and therefore a larger 228mm flywheel and the longer starter, correct?
Should be. But measure the clutch disc to be sure.
This is a 200mm disc
Image may have been reduced in size. Click image to view fullscreen.
Back to top
View user's profile Send private message Gallery Classifieds Feedback
ivwshane
Samba Member


Joined: May 19, 2011
Posts: 947
Location: Sacramento ca
ivwshane is offline 

PostPosted: Fri Jul 06, 2018 9:19 pm    Post subject: Re: Sealing the nose cone (with steel plate)? Reply with quote

Tcash wrote:
I wasn't able to rotate the selector shaft but I was able to pull it out.
In the Neutral position you should be able to rotate the shaft without too much effort. You may need vise grips to hold the shift lever.
Make sure you can rotate it before you put the tranny in.

When I put the nose cone back on I made sure all the selector keys were the same height (so it should have been in neutral, right).
That would be Neutral.

I also measured the bellhousing from the base to the starter flange and it measured 3 1/4" which should mean I have a 091 bellhousing and therefore a larger 228mm flywheel and the longer starter, correct?
Should be. But measure the clutch disc to be sure.
This is a 200mm disc
Image may have been reduced in size. Click image to view fullscreen.


When I put the nose cone on I inserted the hockey stick into the ball joint.

I measured the clutch disc and it measured 228mm.
_________________
77 westy 2.0 FI? (who knows)
71 ghia coup 1600dp
Back to top
View user's profile Send private message Gallery Classifieds Feedback
Tcash
Samba Member


Joined: July 20, 2011
Posts: 12846
Location: San Jose, California, USA
Tcash is online now 

PostPosted: Fri Jul 06, 2018 10:02 pm    Post subject: Re: Sealing the nose cone (with steel plate)? Reply with quote

If the input shaft is the correct length. Your good to go.
Image may have been reduced in size. Click image to view fullscreen.
Back to top
View user's profile Send private message Gallery Classifieds Feedback
ivwshane
Samba Member


Joined: May 19, 2011
Posts: 947
Location: Sacramento ca
ivwshane is offline 

PostPosted: Fri Jul 06, 2018 10:21 pm    Post subject: Re: Sealing the nose cone (with steel plate)? Reply with quote

I measured 26mm.

So what does all this mean?
_________________
77 westy 2.0 FI? (who knows)
71 ghia coup 1600dp
Back to top
View user's profile Send private message Gallery Classifieds Feedback
Tcash
Samba Member


Joined: July 20, 2011
Posts: 12846
Location: San Jose, California, USA
Tcash is online now 

PostPosted: Sat Jul 07, 2018 7:36 am    Post subject: Re: Sealing the nose cone (with steel plate)? Reply with quote

ivwshane wrote:
I measured 26mm.

So what does all this mean?


28-26 I don't think 2mm is going to make a difference.

This means the 091 Bell housing and input shaft where installed on the 002 trans to run on the Type IV engine.

Other than your questionable gearing. Which may not be a factor if you run around town most of the time. The transmission will bolt right up to your Type IV motor.

GD
Tcash
Back to top
View user's profile Send private message Gallery Classifieds Feedback
ivwshane
Samba Member


Joined: May 19, 2011
Posts: 947
Location: Sacramento ca
ivwshane is offline 

PostPosted: Sat Jul 07, 2018 9:49 am    Post subject: Re: Sealing the nose cone (with steel plate)? Reply with quote

Tcash wrote:
ivwshane wrote:
I measured 26mm.

So what does all this mean?


28-26 I don't think 2mm is going to make a difference.

This means the 091 Bell housing and input shaft where installed on the 002 trans to run on the Type IV engine.

Other than your questionable gearing. Which may not be a factor if you run around town most of the time. The transmission will bolt right up to your Type IV motor.

GD
Tcash


Most of my driving is freeway.

Should I check the trans in another gear to see if maybe I wasn't measuring it in fourth correctly?

I would hate to waste money on a transmission if it's not going yield me any gains other than a stronger case (at least for now anyway).
_________________
77 westy 2.0 FI? (who knows)
71 ghia coup 1600dp
Back to top
View user's profile Send private message Gallery Classifieds Feedback
Tcash
Samba Member


Joined: July 20, 2011
Posts: 12846
Location: San Jose, California, USA
Tcash is online now 

PostPosted: Sun Jul 08, 2018 8:48 am    Post subject: Re: Sealing the nose cone (with steel plate)? Reply with quote

Throw it in and try it?
Good luck
Tcash
Back to top
View user's profile Send private message Gallery Classifieds Feedback
ivwshane
Samba Member


Joined: May 19, 2011
Posts: 947
Location: Sacramento ca
ivwshane is offline 

PostPosted: Sun Jul 08, 2018 6:08 pm    Post subject: Re: Sealing the nose cone (with steel plate)? Reply with quote

Tcash wrote:
Throw it in and try it?
Good luck
Tcash


Try what? My transmission is good and was working great before I dropped the engine. I'm just trying to make everything right and do this engine drop once. Dropping the engine and trans is not a trivial thing for me so I prefer to take care of everything now.

The question/issue is whether or not my transmission is really a 091 gearing inside of a 002 housing. A 091 transmission inside of an 002 housing, while not as strong, would not be a deal breaker for me. However, if I'm not getting any benefit from having an 002 transmission then I'd rather get it replaced when a 091.
_________________
77 westy 2.0 FI? (who knows)
71 ghia coup 1600dp
Back to top
View user's profile Send private message Gallery Classifieds Feedback
gears
Samba Member


Joined: October 28, 2002
Posts: 3869
Location: Bend, OR; Kailua, HI
gears is offline 

PostPosted: Mon Jul 09, 2018 9:31 am    Post subject: Re: Sealing the nose cone (with steel plate)? Reply with quote

It doesn't look like an 091 carrier installed on an 002 main case, but measuring the thickness of this flange will tell you. The 091 is 10mm thicker than the 002 to accommodate wider 3rd & 4th gears. (Someone else needs to supply dimensions, as I'm far from any cores.)

Image may have been reduced in size. Click image to view fullscreen.


Even if it's 002, this doesn't mean it hasn't been rebuilt with an 002-style 4.57 R&P. At least half the transaxles floating around have been rebuilt at least once.
_________________
aka Pablo, Geary
9.36 @ 146 in '86
'90 Syncro Westy SVX
'87 Syncro GL 2.5

Needed: Stock 14" x 6" Syncro steel rim
Back to top
View user's profile Send private message Send e-mail Gallery Classifieds Feedback
ivwshane
Samba Member


Joined: May 19, 2011
Posts: 947
Location: Sacramento ca
ivwshane is offline 

PostPosted: Wed Jul 11, 2018 5:45 pm    Post subject: Re: Sealing the nose cone (with steel plate)? Reply with quote

gears wrote:
It doesn't look like an 091 carrier installed on an 002 main case, but measuring the thickness of this flange will tell you. The 091 is 10mm thicker than the 002 to accommodate wider 3rd & 4th gears. (Someone else needs to supply dimensions, as I'm far from any cores.)

Image may have been reduced in size. Click image to view fullscreen.


Even if it's 002, this doesn't mean it hasn't been rebuilt with an 002-style 4.57 R&P. At least half the transaxles floating around have been rebuilt at least once.


Thanks. I'm going to assume its not since that part of the transmission has an 002 part #.
_________________
77 westy 2.0 FI? (who knows)
71 ghia coup 1600dp
Back to top
View user's profile Send private message Gallery Classifieds Feedback
Display posts from previous:   
Reply to topic    Forum Index -> Bay Window Bus All times are Mountain Standard Time/Pacific Daylight Savings Time
Page: Previous  1, 2
Page 2 of 2

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum

About | Help! | Advertise | Donate | Premium Membership | Privacy/Terms of Use | Contact Us | Site Map
Copyright © 1996-2018, Everett Barnes. All Rights Reserved.
Not affiliated with or sponsored by Volkswagen of America | Forum powered by phpBB