Hello! Log in or Register   |  Help  |  Donate  |  Buy Shirts See all banner ads | Advertise on TheSamba.com  
TheSamba.com
 
1968-72 Steering Box Replacement (lots of pix)
Forum Index -> Bay Window Bus Share: Facebook Twitter
Reply to topic
Print View
Quick sort: Show newest posts on top | Show oldest posts on top View previous topic :: View next topic  
Author Message
Tcash
Samba Member


Joined: July 20, 2011
Posts: 12844
Location: San Jose, California, USA
Tcash is offline 

PostPosted: Wed Jul 18, 2018 6:51 pm    Post subject: 1968-72 Steering Box Replacement (lots of pix) Reply with quote

Link
Code:
[url=https://www.thesamba.com/vw/forum/viewtopic.php?t=703510&start=0&postdays=0&postorder=asc&highlight=]1968-72 Steering Box Replacement (lots of pix)[/url]


1968-72 Steering Box Replacement

Editing in progress.

1. Tools L>R: 1/2" & 3/8" drive torque wrench, 1/2"drive ratchet, 3" & 6" 3/8" drive extensions, 3/8" drive ratchet, 13mm & 17mm 3/8" drive sockets, 30mm (1 3/16") 1/2" drive socket, Pin alignment tool that is not a punch, 1/4" straight blade & #3 screwdriver, 13mm Box end wrench, 13mm combination wrench, Needle nose pliers, Cotter pin extractor, Ball peen hammer.
Image may have been reduced in size. Click image to view fullscreen.

2. Tools: OTC 8150 Large Pitman (drop) Arm Puller, 22mm socket 1/2" drive, 1/2" drive ratchet.
Image may have been reduced in size. Click image to view fullscreen.

3. Jack up one side of the vehicle and place a jack stand under the front Beam on that side. Note: the jack stands are placed inward slightly to miss the grease fittings located on the back of the Beam. Lower the jack slightly, to put the weight of the vehicle on the jack stand. Now shake the vehicle, to be sure it is secure on the jack stand. Move to the other side and repeat the procedure.
Image may have been reduced in size. Click image to view fullscreen.

3.a With a 1/4" straight blade screwdriver, remove the two screws from the steering column cap. This allowed me just enough room to get the steering flange off the Steering box.
Image may have been reduced in size. Click image to view fullscreen.

4. Note: I elected not to separate the Drag link from the Drop arm. First let's remove the Drop arm. If you can't get the drop arm off, the Steering box is not coming out. Note: I had been spraying all the fasteners with Rust Penetrant for a couple of weeks in advance in preparation for removing the Steering box.
Image may have been reduced in size. Click image to view fullscreen.

5. Use needle nose pliers straighten the ends of the Cotter pin.
Image may have been reduced in size. Click image to view fullscreen.

6. Remove the Cotter pin with the Extractor tool or Needle nose pliers and a Hammer.
Image may have been reduced in size. Click image to view fullscreen.

Image may have been reduced in size. Click image to view fullscreen.

7. Use 30mm socket with 1/2" drive ratchet. Remove the Drop arm Nut.
Image may have been reduced in size. Click image to view fullscreen.

7a. An Adjustable Spanner can be used. But keep in mind, this Nut can have as much as 80 Ft/lbs of torque on it and be rusted in place. I had been spraying the fasteners with rust penetrant for 2 weeks in advance. Don't round the nut off, go beg borrow or buy a 30mm (1 3/16") socket.
Image may have been reduced in size. Click image to view fullscreen.

8. Note: the Alignment marks on the Drop arm shaft and the Drop arm.
Image may have been reduced in size. Click image to view fullscreen.

9. Position the OTC 8150 puller.
Image may have been reduced in size. Click image to view fullscreen.

10. Pull the Drop arm with the otc 8150 puller, 22mm socket and 1/2" drive ratchet. Remember I presoaked for two weeks.
Note: a 1/2" Impact driver works best for those stubborn arms. In conjunction with the old plumbers trick to break the rust ring.
Image may have been reduced in size. Click image to view fullscreen.

Image may have been reduced in size. Click image to view fullscreen.

11. Remove the Steering box flange, Pinch bolt and Nut, using Two 13mm wrenches.
Image may have been reduced in size. Click image to view fullscreen.

Image may have been reduced in size. Click image to view fullscreen.

12. Steering box flange Pinch Bolt completely removed. Push the Steering coupler with flange straight up. It may take some prying?
Position it to the right of the Steering box shaft.
Image may have been reduced in size. Click image to view fullscreen.

13. Using 17mm socket, 6" extension and 3/8" drive Ratchet. Remove the three steering box mounting bolts at 10,2, and 5 o'clock.
Loosen the mounting bolt located at 7 o'clock until it can easily be removed by hand.
The loose bolt at 7 o'clock will stop the steering box from falling out on your head. Stranger things have happened.
Image may have been reduced in size. Click image to view fullscreen.

Image may have been reduced in size. Click image to view fullscreen.

14. With one hand supporting the Steering box remove the last mounting bolt. Push the Coupler with flange up out of the way, rest it on the right half of the shaft if you have to. Now pull the Steering box straight out.
Image may have been reduced in size. Click image to view fullscreen.

15. Steering box removed.
Image may have been reduced in size. Click image to view fullscreen.

16. Clean the Steering box mating surface and area around it. This will make installation easier as well as leak detection in the future.
Image may have been reduced in size. Click image to view fullscreen.

17. Compare the New steering box to the old one. Mounting bolt holes in the same locations, Worm and Peg shaft splines are the same.
Image may have been reduced in size. Click image to view fullscreen.

18. Note the rubber Worm spindle cap with the nipple on it and the raised Centering mark cast into the Steering box. These where added June 1971. The New box is missing this and the Red fill plug.
Image may have been reduced in size. Click image to view fullscreen.

19. Note the Nipple on the Worm spindle cap for center is at 9 o'clock and the relief for the pinch bolt in the Worm shaft is at 12 0'clock.
wolfgangint wrote:
NOTE: There are two different input shafts on these steering boxes with the detent 90 degrees off. If your steering wheel spokes are 90 degrees off you will correct that by removing the mount bolts from the rubber coupler and repositioning it 90 degrees.

Spray and clean the Worm spindle splines and Gently pry the Worm spindle cap up high enough to get your fingers under it and pull it off, carefully.
Image may have been reduced in size. Click image to view fullscreen.

Image may have been reduced in size. Click image to view fullscreen.

20. Worm spindle cap installation.
Rotate the Worm shaft Clockwise until it stops, make a mark in alignment with the Centering hump cast into the steer box case.
Rotate the Worm shaft Counter clockwise until it stops and make a mark aligned with the Centering hump.
Image may have been reduced in size. Click image to view fullscreen.

21. Now turn the Worm shaft Clockwise half of the rotation from stop to stop. This is where you end up. Note the Centering hump is located in the middle of the two marks. Grease the seal that the Worm spindle cap will ride on.
Image may have been reduced in size. Click image to view fullscreen.

22. Align the Worm spindle cap and push it on with your fingers.
Image may have been reduced in size. Click image to view fullscreen.

23. Time for some Steering box lube. What ever you choose you will need 9 2/3 oz (285.87 ml).
More Lube information located here.
Link = Steering Box Lube
Image may have been reduced in size. Click image to view fullscreen.

24. Injected using this multi fit nozzle I got from my Friendly Local Auto Parts Store.
Image may have been reduced in size. Click image to view fullscreen.

25. Piercing the air bubbles all the time.
Image may have been reduced in size. Click image to view fullscreen.

26. 20 minutes later, full to the brim.
Image may have been reduced in size. Click image to view fullscreen.

27. Ok time for lunch. Shrimp fried rice made by my lovely wife, with a salad of Iceberg lettuce, Union slices, Julienned carrots, lightly drizzled with The olive bar black currant balsamic, with a splash of Red wine vinegar, topped with Parmesan Romano & Asiago cheese. Paired with Lemon water. For desert a half a Watermelon. Eaten with a couple of AFM flap opening tools.
Image may have been reduced in size. Click image to view fullscreen.

28. Back from lunch and my afternoon nap. 2 hrs have gone by and the Steering box lube is still at full brim.
Image may have been reduced in size. Click image to view fullscreen.

29. Note the tension Spring and O-ring on the fill plug.
Image may have been reduced in size. Click image to view fullscreen.

Image may have been reduced in size. Click image to view fullscreen.

30. The Grey line indicates the amount I used of the 500ml bottle. With some burping and spillage waste.
Image may have been reduced in size. Click image to view fullscreen.

31. Fasteners laid out with Anti-Sieze applied.
Image may have been reduced in size. Click image to view fullscreen.

31.a Slide the Steer box back in, install one of the bolts loosely to hold it in place.
Image may have been reduced in size. Click image to view fullscreen.

32. Note this is misalignment. The Steering flange will only go on one way.
Image may have been reduced in size. Click image to view fullscreen.

33. Draw a line down the center of the Flange. It makes it easier to line up the Flange with the splines on the Worm drive shaft.
Image may have been reduced in size. Click image to view fullscreen.

34. Use the bolt as a visual aid to check alignment.
Slide the Flange down and use the Alignment tool or (#3 screwdriver) to align the hole. Followed by the bolt.
CAUTION the bolt must go in by hand or Damage to the Worm drive splines and or the bolt will occur.
NO hammering no Screwing it in with a socket. Have some patients here. You will find that aligned spot where the bolt just slides in.
Image may have been reduced in size. Click image to view fullscreen.

35. Flange bolt and nut installed.
Image may have been reduced in size. Click image to view fullscreen.

36. With 13mm wrench, 13mm socket, 3" extension, 3/8" drive torque wrench. Torque the Pinch bolt to 18 ft/lbs.
Image may have been reduced in size. Click image to view fullscreen.

37. Using 17mm socket, 6" extension and 3/8" drive torque wrench. Install the rest of the Steering box mounting bolts and torque to 25-36 ft/lbs.
Image may have been reduced in size. Click image to view fullscreen.

38. Line up the marks on the Drop arm shaft (peg shaft) and the Drop arm. As I elected not to remove the Drag link. The easiest way to do this is to turn the steering coupler with one hand and slip the drop arm on with the other. Coat the threads and face of the drop arm with Anti-Sieze.
Image may have been reduced in size. Click image to view fullscreen.

39. Install the Drop arm nut, with the 30mm (1 3/16") Socket and 1/2" drive torque wrench, torque the nut to 58 ft/lbs.
Look to see if the Cotter key hole is lined up with the valley in the Castle nut.
No, set the torque wrench to 80 ft/lbs and slightly tighten the nut until the Cotter key can be dropped in.
If you reach 80 ft/lbs and still no Cotter pin hole. Take the nut off and start over.
Image may have been reduced in size. Click image to view fullscreen.

40. Drop a new 3mm X 25mm Cotter key in from the top and bend the ends over to form the shape of an anchor.
Image may have been reduced in size. Click image to view fullscreen.

41. With a 1/4" straight blade screwdriver, install the two screws from the steering column cap.
Image may have been reduced in size. Click image to view fullscreen.

42. While you have the grease gun out give the five grease fittings on the front Beam a few pumps. Remember I said to note where the jack stand was.
Image may have been reduced in size. Click image to view fullscreen.

Remove the jack stands in the reverse order of #3.



43. Now take it out for a test drive on a smooth flat road . Feel the smooth turning of the wheel.

If the Steering wheel is not centered.

wolfgangint wrote:
NOTE: There are two different input shafts on these steering boxes with the detent 90 degrees off. If your steering wheel spokes are 90 degrees off you will correct that by removing the mount bolts from the rubber coupler and repositioning it 90 degrees.


The Steering flange only goes on one way, so there is no adjustment. The only adjustment is to change the position of the steering coupler.

Pull the Drop arm nut off and double check the alignment marks.

On pre June 1971 steering box's.
1. Use a seamstress tape and put a piece of tape in the center of the two steering wheel spokes on top of the steering wheel.

2. Put a piece of tape on the dash board in alignment with the center of the horn button and the center of the steering wheel.

3. Turn the steering wheel to the right until it stops, put a piece of tape on the steering wheel in alignment with the tape on the center of the dash.

4. Now turn the wheel to the left until it stops, put a piece of tape on the steering wheel in alignment with the tape on the center of the dash.

5. Measure between these two points on the top of the steering wheel and put a piece of tape on the steering wheel. This is the steering box center of travel.

6. Align the Center mark for the Steering Box with the center mark on the dash.

7. Without moving the steering shaft, remove the steering wheel and adjust as required so the center mark on the steering wheel is aligned with the center mark on the dash.

On June of 1971 and later steering box's with the Centering alignment marks on the steering box.
Align the Worm spindle cap with the centering mark on the steer box and check the steering wheel alignment. Adjust as necessary.

After the Steering wheel has been Centered and you have Double checked the Drop arm Alignment marks. If the wheel is not centered going down the road, a Front end wheel alignment will be required.
Back to top
View user's profile Send private message Gallery Classifieds Feedback
Display posts from previous:   
Reply to topic    Forum Index -> Bay Window Bus All times are Mountain Standard Time/Pacific Daylight Savings Time
Page 1 of 1

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum

About | Help! | Advertise | Donate | Premium Membership | Privacy/Terms of Use | Contact Us | Site Map
Copyright © 1996-2023, Everett Barnes. All Rights Reserved.
Not affiliated with or sponsored by Volkswagen of America | Forum powered by phpBB
Links to eBay or other vendor sites may be affiliate links where the site receives compensation.