| TRS63 |
Tue Feb 20, 2024 12:24 pm |
|
What a clean work 8)
Antoine |
|
| WrennMetallWerks |
Tue Feb 20, 2024 5:05 pm |
|
| ⬆️⬆️⬆️ Thanks So Much Brother ⬆️⬆️⬆️ |
|
| WrennMetallWerks |
Tue Feb 20, 2024 5:07 pm |
|
Off to a good start on the passenger side. I got multiple panels made, fitted and tacked into place.
|
|
| WrennMetallWerks |
Wed Feb 21, 2024 9:21 pm |
|
|
|
| VeloMikey |
Thu Feb 22, 2024 7:11 am |
|
| Looks like you have done this once or twice! Keep up the good work Jason! |
|
| WrennMetallWerks |
Thu Feb 22, 2024 9:35 am |
|
⬆️⬆️⬆️Thanks Mr Mike⬆️⬆️⬆️
I will be all warmed up when I get to yours ⚒🤍☑️ |
|
| WrennMetallWerks |
Thu Feb 22, 2024 5:56 pm |
|
Added the Jack point detail and located the torsion cover hole and final fit the panel.
I discovered a ton of lead that was covering some yuckyness. I removed all that and started hand shaping the lower fender.
Ya know ever once in a while I have to remake something. The lower front fender panel I put on yesterday had to be made again. I attached it with out noticing damage to the fender that was causing it to be all of of wack. I cut it off. Made a new and bigger patch panel and all was good in the universe. 😜👊
|
|
| WrennMetallWerks |
Sat Feb 24, 2024 1:35 pm |
|
|
|
| WrennMetallWerks |
Mon Mar 25, 2024 10:40 am |
|
Hey folks…. This rotation we are back on the 59 kab
First Order of business will be to weld up and metal finish the passenger side lower repairs.
Once we are happy there it’s time to address a bunch of random dents and holes on the driver rear quarter. The creases and slide hammer holes in the fender do not look horrible in photos but don’t let it’s good looks fool ya. 😜👊
|
|
| VeloMikey |
Mon Mar 25, 2024 4:55 pm |
|
| Almost as bad as my QP! |
|
| WrennMetallWerks |
Mon Mar 25, 2024 5:03 pm |
|
⬆️⬆️⬆️Rite⬆️⬆️⬆️
I’m so glad folks do not use slide hammers like that anymore. 😜👊 |
|
| WrennMetallWerks |
Tue Mar 26, 2024 6:54 pm |
|
Moving rite along.
Still a bit more metal to move on the driver res quarter up a huge improvement
We even started taking care of the inner heater channel repair
This one is on track to be wrapped up in record time again. 🤩👊
|
|
| WrennMetallWerks |
Sun Mar 31, 2024 10:12 am |
|
Heater channels are in the books , rear quarter sorted out Front firewall repair completed, front fender sorted out , fender mirrors and antenna holes filled. Cursing rite along.
|
|
| Andrew Kienitz |
Sun Apr 14, 2024 3:50 pm |
|
| Been watching your thread and can't get over the metal work and skill associated with this project. 1st class work and attention to detail. Thanks for sharing this. I am contemplating a 1956 hardtop restoration. Andy |
|
| WrennMetallWerks |
Sun Apr 14, 2024 3:53 pm |
|
| ⬆️⬆️⬆️Thanks so much for that. Your welcome. I’m glad your enjoying it. ⬆️⬆️ |
|
| WrennMetallWerks |
Mon Apr 15, 2024 12:27 pm |
|
Back at it …..
|
|
| Andrew Kienitz |
Mon Apr 15, 2024 7:09 pm |
|
| I'm guessing you fabricated the body frame that allows the body to tilt down incrementally. Would you mind sharing the general fabrication measurements. It seems like it works well and has an element of simplicity. Thanks Andy |
|
| WrennMetallWerks |
Mon Apr 15, 2024 9:11 pm |
|
⬆️⬆️⬆️ Hey buddy…. You nailed it… it’s super simple and also very user friendly. I rolled this over by myself with no problems. ⬆️⬆️⬆️
Tomorrow I will get some measurements for ya. Fairly easy to build and fun to use. ⚒☑️🤍 |
|
| WrennMetallWerks |
Mon Apr 15, 2024 9:21 pm |
|
|
|
| TRS63 |
Tue Apr 16, 2024 7:54 am |
|
Looking good and clean as always😍
Thanks for sharing
Antoine |
|
Powered by phpBB © 2001, 2005 phpBB Group
|