| Author |
Message |
greentrc6
Samba Member
Joined: September 07, 2008
Posts: 14
Location: Victorville
|
 Posted: Sun Oct 01, 2023 11:35 pm Post subject: Re: 71 Baja build |
 |
|
Well, I have gotten a bit more done recently. Gauges mounted in new dash Switchpros wired. The whole car is all wired up now. I got my fuel fill set about where it's going to be. The fuel vent/rollover is run out at the bottom of the car. The air filter is mounted and the tubing is all run. Switched over to some Tensor 35's. The rear fenders are mounted up. I have about 100 street miles on it so far. Cut out some vents on the front end for some air flow, but I need to change the material I used, it doesn't allow enough airflow. Even went to a local cars and coffee meet this morning.
|
|
| Back to top |
|
 |
indianpeaksjoe
Samba Member
Joined: July 27, 2017
Posts: 606
Location: Moab, UT
|
| Posted: Mon Oct 02, 2023 5:03 am Post subject: Re: 71 Baja build |
|
|
Woah! that is some serious work there, looks great.
-Joe |
|
| Back to top |
|
|
dirtkeeper
Samba Member
Joined: February 19, 2008
Posts: 3251
Location: Left of everywhere
|
| Posted: Mon Oct 02, 2023 6:34 am Post subject: Re: 71 Baja build |
|
|
| Very cool! Nice work |
|
| Back to top |
|
|
ORANGECRUSHer
Samba Member
Joined: June 09, 2006
Posts: 3367
Location: West Coast (Michigan's)
|
| Posted: Tue Oct 03, 2023 1:31 pm Post subject: Re: 71 Baja build |
|
|
Is that PVC tubing for the gas filler??
_________________
Brian H.
OrangeCrushERBerrien Warrior-2.4L Quad4-2x3 arms-1.5Fox coilovers-094-930CVs
LAZY MARY1970 Baja 2110cc-82mm CB forged crank-AA pistons/cylinders-Grant rings-1.1 vw rockers-CB serpkit-CB chromoly PRs-CB maxiflow filter pump-wix51515 filter-Dual 44IDF-cut/turned front beam-AEM wideband-Auber CHT-Donaldson Dual PowerCore filters-custom AL air boxes |
|
| Back to top |
|
|
greentrc6
Samba Member
Joined: September 07, 2008
Posts: 14
Location: Victorville
|
| Posted: Tue Oct 03, 2023 10:47 pm Post subject: Re: 71 Baja build |
|
|
| ORANGECRUSHer wrote: |
| Is that PVC tubing for the gas filler?? |
Yea, it's the Fuelsafe hose that Kartek carries. Don't worry I didn't get it at Ace hardware. |
|
| Back to top |
|
|
ORANGECRUSHer
Samba Member
Joined: June 09, 2006
Posts: 3367
Location: West Coast (Michigan's)
|
| Posted: Wed Oct 04, 2023 5:41 pm Post subject: Re: 71 Baja build |
|
|
I was just curious because I have a similar setup and never committed to hooking hose up to it.
_________________
Brian H.
OrangeCrushERBerrien Warrior-2.4L Quad4-2x3 arms-1.5Fox coilovers-094-930CVs
LAZY MARY1970 Baja 2110cc-82mm CB forged crank-AA pistons/cylinders-Grant rings-1.1 vw rockers-CB serpkit-CB chromoly PRs-CB maxiflow filter pump-wix51515 filter-Dual 44IDF-cut/turned front beam-AEM wideband-Auber CHT-Donaldson Dual PowerCore filters-custom AL air boxes |
|
| Back to top |
|
|
greentrc6
Samba Member
Joined: September 07, 2008
Posts: 14
Location: Victorville
|
| Posted: Fri Nov 10, 2023 10:28 pm Post subject: Re: 71 Baja build |
|
|
Some fun in Dove Springs
|
|
| Back to top |
|
|
|
