Author |
Message |
PareosWC Samba Member
Joined: April 26, 2016 Posts: 3 Location: Upstate SC
|
Posted: Tue Apr 26, 2016 11:31 am Post subject: R-1 RATT-V |
|
|
Hello, guys. This is my first post, and I can tell I have a lot of reading ahead of me. I had no idea there were so many details that separate models of VW based vehicles
My offering is this R-1 Rescue All Terrain Transport. I used it as a Pararescueman in the AF, and now I'm closing the deal on owning one. This R-1 doesn't have a motor or tranny, but I recall that it either used a Type 1 or Type 4 motor, and perhaps mated to a 091 transmission- set up for automatic. Some guys say a 914 motor, then some say from a bus is fine?
I would like to keep it VW based as original, but some guys have talked about putting a Corvair motor and Powerglide tranny in it? Anyway, I appreciate the website, and if you have any recommendations as to what I should throw in it, I will be listening.
The plan is to first get it, then perhaps place a Type 1 and 091 in it.
[/img] |
|
Back to top |
|
 |
danielzink Samba Member

Joined: August 03, 2004 Posts: 288 Location: Lansing Michigan
|
Posted: Tue Apr 26, 2016 1:24 pm Post subject: Re: R-1 RATT-V |
|
|
If it's a type 4 motor then yes - bus or 914 - identical.
Dan _________________ 1965 Notchback 2300cc Type4
Subaru Powered Rail
1915 Rail
www.danielzink.com |
|
Back to top |
|
 |
PareosWC Samba Member
Joined: April 26, 2016 Posts: 3 Location: Upstate SC
|
Posted: Wed Apr 27, 2016 4:12 am Post subject: Re: R-1 RATT-V |
|
|
Dan, would a Type 1 motor hooked up to a 091 be the easiest proposition? I would have to install a clutch pedal/linkage, as the original set up was an automatic transmission from a bus, I believe.
I wonder what challenges I would run into- a good bit of fab work?? |
|
Back to top |
|
 |
Aerindel Samba Member
Joined: May 30, 2015 Posts: 459 Location: Western Montana
|
Posted: Wed Apr 27, 2016 4:26 am Post subject: Re: R-1 RATT-V |
|
|
Do a hydraulic clutch. Only fab is bolting in a pedal and running some brake line. Shouldn't take more than an hour to set it up. _________________ Homemade woods/street, bug out rail. IRS, Balljoint front end. 1967 1600cc DP, Weber 32/36 progressive, tri-mil quiet pack. Rear only cutting brakes.
http://www.thesamba.com/vw/forum/viewtopic.php?t=630046 |
|
Back to top |
|
 |
danielzink Samba Member

Joined: August 03, 2004 Posts: 288 Location: Lansing Michigan
|
Posted: Wed Apr 27, 2016 6:51 am Post subject: Re: R-1 RATT-V |
|
|
PareosWC wrote: |
Dan, would a Type 1 motor hooked up to a 091 be the easiest proposition? I would have to install a clutch pedal/linkage, as the original set up was an automatic transmission from a bus, I believe.
I wonder what challenges I would run into- a good bit of fab work?? |
Aerindel wrote: |
Do a hydraulic clutch. Only fab is bolting in a pedal and running some brake line. Shouldn't take more than an hour to set it up. |
Aerindel is right. You could do a hydraulic setup as in most buggies/rails - easy. (something like this: http://www.appletreeauto.com/ECONOMY-PEDAL-KIT-AC7...CHpbw_wcB)
Run the 091 and go !
Dan _________________ 1965 Notchback 2300cc Type4
Subaru Powered Rail
1915 Rail
www.danielzink.com |
|
Back to top |
|
 |
PareosWC Samba Member
Joined: April 26, 2016 Posts: 3 Location: Upstate SC
|
Posted: Thu Apr 28, 2016 1:08 pm Post subject: Re: R-1 RATT-V |
|
|
So, I've learned a lot in the past 48hrs.
Apparently, the motor is indeed a Type 4, but may have been using an AUDI automatic transmission that was popular with off roaders in the 90's for buggies? The shifter appears to be an Art Carr design? But then that and the auto trans proposition appeared to be about $15K?
I believe a type 4 mated to a 091, and the hydro clutch is going to be the ticket on this build. Or a type 4 mated to VW bus auto trans?
|
|
Back to top |
|
 |
bullnerd Samba Member
Joined: September 08, 2011 Posts: 64 Location: NJ
|
Posted: Fri Apr 29, 2016 7:28 am Post subject: Re: R-1 RATT-V |
|
|
That thing is baddass!
Thanks for posting. |
|
Back to top |
|
 |
BFB Samba Member

Joined: November 03, 2014 Posts: 2610
|
Posted: Sat Jul 05, 2025 2:05 pm Post subject: Re: R-1 RATT-V |
|
|
Just bumping because this thing looked cool.
Also anyone know anything about the Audi transaxle he mentioned? _________________ "how am i supposed to torque the rear wheel nut to 250 ft lbs??? " - clonebug
An interesting thing happens in forums where everyone starts parroting the same thing and "common knowledge" takes over.
Most experts aren't. |
|
Back to top |
|
 |
oprn Samba Member

Joined: November 13, 2016 Posts: 14687 Location: Western Canada
|
Posted: Sat Jul 05, 2025 3:57 pm Post subject: Re: R-1 RATT-V |
|
|
As far as I know all Audi transaxles are from front wheel drive cars. Unless you can flip the diff carrier like the type 1 transaxles you are going to have one slow gear forward and the rest in reverse. _________________ Our cars get old, we get old but driving an old VW never gets old! |
|
Back to top |
|
 |
|