| Author |
Message |
SAW
Samba Member
Joined: August 04, 2005
Posts: 21
Location: San Diego
|
 Posted: Wed Feb 27, 2008 2:04 pm Post subject: San Diego VW engine builder? |
 |
|
| I need to find a reputable VW engine builder here in San Diego. Anyone out there have some suggestions?? let me know . Thanks! |
|
| Back to top |
|
 |
Stripped66
Samba Member
Joined: May 31, 2005
Posts: 3509
Location: Charleston, SC
|
| Posted: Wed Feb 27, 2008 3:02 pm Post subject: |
|
|
VW Paradise in San Marcos.
_________________
| 66brm wrote: |
| Bodacious wrote: |
| Why not just make a custom set of wires with a Y splice in them. Then you could just run one distributor. |
I don't think electrickery works that way |
|
|
| Back to top |
|
|
SLC62Ragtop
Samba Member
Joined: June 03, 2007
Posts: 63
|
|
| Back to top |
|
|
Glenn 
Mr. 010
Joined: December 25, 2001
Posts: 79466
Location: Sneaking up behind you
|
| Posted: Wed Feb 27, 2008 8:34 pm Post subject: |
|
|
Therre must be a dozen good builders withing driving distance.
But Art built my engine and I can't say enough good things about the experience.
_________________
Glenn
74 Beetle Specs | 74 Beetle Restoration | 2180cc Engine
"You may not get what you pay for, but you always pay for what you get"
Member #1009
#BlueSquare
עַם יִשְׂרָאֵל חַי |
|
| Back to top |
|
|
SLC62Ragtop
Samba Member
Joined: June 03, 2007
Posts: 63
|
| Posted: Wed Feb 27, 2008 8:38 pm Post subject: |
|
|
| Glenn wrote: |
Therre must be a dozen good builders withing driving distance.
But Art built my engine and I can't say enough good things about the experience. |
They will be building mine as well. I have been to several VW shops ( AZ, CA and UT) during my military days and his shop is 100% hands down the best. The quality and attention to detail is top notch.
_________________
62 ragtop.
ACE The number #1 Aircooled VW Shop |
|
| Back to top |
|
|
SAW
Samba Member
Joined: August 04, 2005
Posts: 21
Location: San Diego
|
| Posted: Thu Feb 28, 2008 8:32 pm Post subject: |
|
|
| thanks alot for the heads up on the ACE shop. I wish I was closer to Salt Lake. that place looks seriously skilled. |
|
| Back to top |
|
|
Glenn
Mr. 010
Joined: December 25, 2001
Posts: 79466
Location: Sneaking up behind you
|
| Posted: Thu Feb 28, 2008 8:35 pm Post subject: |
|
|
| SAW wrote: |
| thanks alot for the heads up on the ACE shop. I wish I was closer to Salt Lake. that place looks seriously skilled. |
Art ships using UPS Freight. It cost me $200 to ship a long block from SLC to Long Island.
_________________
Glenn
74 Beetle Specs | 74 Beetle Restoration | 2180cc Engine
"You may not get what you pay for, but you always pay for what you get"
Member #1009
#BlueSquare
עַם יִשְׂרָאֵל חַי |
|
| Back to top |
|
|
SLC62Ragtop
Samba Member
Joined: June 03, 2007
Posts: 63
|
| Posted: Thu Feb 28, 2008 8:38 pm Post subject: |
|
|
| SAW wrote: |
| thanks alot for the heads up on the ACE shop. I wish I was closer to Salt Lake. that place looks seriously skilled. |
The internet, phone and shipping makes you as close as you want to be. 
Honestly, you can not go wrong with an ACE built motor.
_________________
62 ragtop.
ACE The number #1 Aircooled VW Shop |
|
| Back to top |
|
|
CJG
Samba Member
Joined: November 07, 2005
Posts: 571
Location: Phoenix
|
| Posted: Thu Feb 28, 2008 9:09 pm Post subject: |
|
|
Why have it shipped when you have one of the best engine builders right there at your finger tips, down the road in Orange County, DRD another great engine builder does everything in house, why go out of state.  |
|
| Back to top |
|
|
SLC62Ragtop
Samba Member
Joined: June 03, 2007
Posts: 63
|
| Posted: Thu Feb 28, 2008 9:13 pm Post subject: |
|
|
| CJG wrote: |
| Why have it shipped when you have one of the best engine builders right there at your finger tips, down the road in Orange County, DRD another great engine builder does everything in house, why go out of state. |
DRD makes some nice stuff. However after seeing all the resent reviews and posts about people waiting 2-9 months it made me nervous.
The saying is perfection takes time, but not that much time.
_________________
62 ragtop.
ACE The number #1 Aircooled VW Shop |
|
| Back to top |
|
|
CJG
Samba Member
Joined: November 07, 2005
Posts: 571
Location: Phoenix
|
| Posted: Thu Feb 28, 2008 9:21 pm Post subject: |
|
|
| Why not VW Paradise then,they do great work and do everything in house also. |
|
| Back to top |
|
|
abzillah
Samba Member
Joined: November 24, 2006
Posts: 75
|
| Posted: Thu Feb 28, 2008 9:34 pm Post subject: |
|
|
VW Paradise is good, they are located in San Marcos.
I got my engine from Kline VW repair, and they are in east county in Lake Side. I have gotten two engines from Kline and my buddy did also. My buddy's car is a daily driver, and he has put over 20K miles in driving it these two past years. They have good prices. Search the name on google maps and it will give you all the info. Check out his shop and everything that he has and talk to him. He's a nice guy and has very good service. After installing your engine, he will tune it for you and also provides warranty. |
|
| Back to top |
|
|
FG1732
Samba Member
Joined: March 03, 2004
Posts: 354
|
| Posted: Sat Mar 01, 2008 2:24 pm Post subject: |
|
|
DO NOT use Vw Paradise.
They are on the low end when it comes to customer service and they are on the pricey side. |
|
| Back to top |
|
|
SLC62Ragtop
Samba Member
Joined: June 03, 2007
Posts: 63
|
| Posted: Sat Mar 01, 2008 3:44 pm Post subject: |
|
|
| ArtistAntonio wrote: |
DO NOT use Vw Paradise.
They are on the low end when it comes to customer service and they are on the pricey side. |
I have heard that as well.
_________________
62 ragtop.
ACE The number #1 Aircooled VW Shop |
|
| Back to top |
|
|
neil68
Samba Member
Joined: March 17, 2007
Posts: 3448
Location: Calgary, Canada
|
| Posted: Sat Mar 01, 2008 4:54 pm Post subject: San Diego car meets? |
|
|
On a related San Diego question: I'll be in San Diego next week. Are there any local car meets, drive-ins, etc?
Thanks!
_________________
Neil.
Der Kleiner Rennwagens
‘68 Beetle 2332 cc, 204 WHP
12.5 seconds @ 108 mph
Dynojet Test: https://www.youtube.com/watch?v=M9B_H3eklAo |
|
| Back to top |
|
|
Glenn
Mr. 010
Joined: December 25, 2001
Posts: 79466
Location: Sneaking up behind you
|
| Posted: Sat Mar 01, 2008 4:56 pm Post subject: |
|
|
| SLC62Ragtop wrote: |
| CJG wrote: |
| Why have it shipped when you have one of the best engine builders right there at your finger tips, down the road in Orange County, DRD another great engine builder does everything in house, why go out of state. |
DRD makes some nice stuff. However after seeing all the resent reviews and posts about people waiting 2-9 months it made me nervous.
The saying is perfection takes time, but not that much time. |
My friend got a DRD 2276 in just a few months. Darren did a great job.... it's a beast.
_________________
Glenn
74 Beetle Specs | 74 Beetle Restoration | 2180cc Engine
"You may not get what you pay for, but you always pay for what you get"
Member #1009
#BlueSquare
עַם יִשְׂרָאֵל חַי |
|
| Back to top |
|
|
SLC62Ragtop
Samba Member
Joined: June 03, 2007
Posts: 63
|
| Posted: Sat Mar 01, 2008 6:20 pm Post subject: |
|
|
| Glenn wrote: |
| SLC62Ragtop wrote: |
| CJG wrote: |
| Why have it shipped when you have one of the best engine builders right there at your finger tips, down the road in Orange County, DRD another great engine builder does everything in house, why go out of state. |
DRD makes some nice stuff. However after seeing all the resent reviews and posts about people waiting 2-9 months it made me nervous.
The saying is perfection takes time, but not that much time. |
My friend got a DRD 2276 in just a few months. Darren did a great job.... it's a beast. |
I agree with you on how their stuff performs. I had a buddy that was in the military with me that had a 2276 from them that ripped. It took almost 5 months to get though and there seems to be more and more people postng about how long it takes while others seem to get things fast. For me that makes me uncomfortable because my money spends the same as anyone elses.
_________________
62 ragtop.
ACE The number #1 Aircooled VW Shop |
|
| Back to top |
|
|
vwairheads
Samba Member
Joined: March 26, 2007
Posts: 675
Location: chula vista
|
| Posted: Sun Mar 02, 2008 7:49 am Post subject: |
|
|
5 months of agony  thats too long.hope darren can reduce that agony.  |
|
| Back to top |
|
|
Howard Sanson
Samba Member
Joined: October 25, 2007
Posts: 68
Location: 15 and 91 frwy
|
| Posted: Sun Mar 02, 2008 9:49 am Post subject: |
|
|
| Here is someone steve tims (909) 689-7475 call and talk to them honestfair and good work. |
|
| Back to top |
|
|
PV AUTO
Samba Member
Joined: October 10, 2007
Posts: 67
Location: SAN DIEGO
|
| Posted: Sat Jan 24, 2009 8:27 am Post subject: |
|
|
i know this thread is a litle old but and i recently took my aluminum case to kline vw in lakeside and asked them to clearance the case for a 82 crank, 94 pistons, gusset the roof on top of #3 and #1 cylinders, and fill in behind #3. well the wedl job was completely horrible  they were cold welds that looked like bubble gum and some sections they had huge gaps and totally missed te case and just welded the gussets. now as far as the clearanceing they had almost a 1/4 gap from the smallest clearance from the rod to the roof of the case which in turn caused 3 holes on the roof of the case  they tried to patch 1 hole by welding this huge gob of weld on it. now they gave it back to me like this not seeing the other 2 holes i put the case halves together and measured a 32 thousandths gap in between  needless to say i gave up on that case. i can say he was understanding and a good person but i ended up leaving a NEW alum. case and walked out with a USED as21 case and a $300 refund. so for anybody looking for machine work in so. cal. i would suggest you stick with best and think twice on kline for any machine work. |
|
| Back to top |
|
|
|
