| Author |
Message |
Schroby
Samba Member
Joined: July 03, 2005
Posts: 19
|
 Posted: Fri Oct 27, 2006 11:07 am Post subject: How to identify genuine Centerline Wheels |
 |
|
Hello, I have come across some 4-lug Centerline Wheels for sale. How do I confirm they are genuine Centerlines? The only stampings are the size 15x4.5 on the backside and they appear to be a 1-piece wheel. They are for sale for $90 with weather cracked tires. Is this a good deal? Are they worth it?
Thanks for your help! |
|
| Back to top |
|
 |
TomSimon
Samba Member
Joined: January 13, 2004
Posts: 753
|
| Posted: Sat Oct 28, 2006 11:24 am Post subject: |
|
|
There are a few fakes that were manufactured...
the "not so good ones" are cast an done piece, they have these rivets lookin gthing that are ornimental only, they don't serve any function other than to make the cast wheel look like a centerline. These are not a bad wheel mind you, but a bi of a "poser" in my opinion. Cast is heavier than any spun aluminim design, since cast aluminum is inherently weaker than a wheel metal spun from wrought or rolled aluminum plate
There are other spun aluminum wheels out there that use 15 bolts to hold the halves together, instead of having the signature smashed stainless steel rivets of a Centerline, but you said the wheels you were looking at are not 2-piece.
I wouldn't pay more than $50/wheel for those cast "centerline copies" I hope that helps |
|
| Back to top |
|
|
Neil Davies
Samba Member
Joined: July 31, 2005
Posts: 393
Location: Kidderminster, West Midlands, UK
|
| Posted: Wed Nov 01, 2006 4:55 am Post subject: |
|
|
The other thing is that genuine Center Lines have the name around the hole in the middle. Repro wheels won't have this. I don't know if Tom meant repro rather than fakes? I've not heard of any fake wheels being passed off as genuine?
_________________
'67/'68 Cal Look Beetle, 2007cc, 48IDFs, 14.4 @ 93mph, Oct 2017.
'68/'70 Karmann Beetle, wife's project, progressing slowly.
'80 Devon Moonraker, wife's ratty but cool toy.
'86 Scirocco special project - still measuring up... |
|
| Back to top |
|
|
66 Käfer
Samba Member
Joined: November 24, 2003
Posts: 217
Location: Cooper City
|
| Posted: Wed Feb 14, 2007 11:14 am Post subject: |
|
|
| Sounds like the ones you are looking at are American Eagles. They have the markings on the inside but they are hard to see, not very legible. They aren't bad but like Tom Simon said, they are not Centerlines. For a street wheel, they may be a better choice since they hold-up better if you hit a curb or pot-hole. If you are getting the whole set for 90, that is a good deal. 90 each is a little much considering that is what they cost new back in those days. Hell you can get 8 spoke empis for about that. |
|
| Back to top |
|
|
66 Käfer
Samba Member
Joined: November 24, 2003
Posts: 217
Location: Cooper City
|
| Posted: Wed Feb 14, 2007 11:18 am Post subject: |
|
|
| Neil Davies wrote: |
| The other thing is that genuine Center Lines have the name around the hole in the middle... |
This is true on the 4-lug wheels, wide 5s don't have the Centerline name on them. Chevy and Ford bolt-pattern wheels have the name on them also.
Centerlines are a distinct 2-piece wheel, you can see the split where the 2 halves meet through the center bore. When you see a Centerline next to a look-alike, the difference is obvious. |
|
| Back to top |
|
|
gunther hoff
Samba Member
Joined: December 05, 2005
Posts: 15
|
| Posted: Wed Feb 14, 2007 8:48 pm Post subject: |
|
|
| TomSimon wrote: |
| There are other spun aluminum wheels out there that use 15 bolts to hold the halves together, instead of having the signature smashed stainless steel rivets of a Centerline, |
More than likely these (spoken of by Tom) are CMS wheels. Which by the way is a very good quality wheel. Their whole initial design was so that one could quick change the inner and outer halves at the trace or course if needed to accommodate a variety of tires. An ajustable offset if you will.
_________________
From the islands to the mountains... |
|
| Back to top |
|
|
|
