Author |
Message |
Weezle Samba Member

Joined: February 07, 2014 Posts: 491 Location: ORLANDO
|
Posted: Wed Dec 23, 2020 5:34 pm Post subject: Treatment of edges of repair panels welded into pan |
|
|
I had to weld in some quarter pans. I drilled holes around the edges of the patches and made some spot or puddle welds there. The patches were laid on top of the pans and overlap a bit. My question is how to handle the edges. Should I prime and brush on seam sealer then paint or would the metalized epoxy like USC all metal work well there? That could be sanded smooth and would look better but I’m afraid it would crack. It’s my first time doing this. Thanks. _________________ Run Forrest, Run!
http://www.thesamba.com/vw/forum/viewtopic.php?t=604918&postdays=0&postorder=asc&start=0 |
|
Back to top |
|
 |
VW_Jimbo  Samba Member

Joined: May 22, 2016 Posts: 6412 Location: Huntington Beach, CA
|
Posted: Wed Dec 23, 2020 7:41 pm Post subject: Re: Treatment of edges of repair panels welded into pan |
|
|
A butt joint there would have been best. It would naturally keep moisture from gaining access. In lieu of that, a seam sealer is the alternative. Gob it on there, prime it and paint. _________________ Jimbo
There is never enough time to do it right the first time, but all the time necessary the second time!
nshaddox wrote: |
Plus I tend to prefer these impossible projects that take way too much time. There’s no thrill in easy projects. Challenges are fun. |
67rustavenger wrote: |
GFY's Xevin and VW_Jimbo!  |
|
|
Back to top |
|
 |
RLFD213 Samba Member
Joined: January 21, 2009 Posts: 134
|
Posted: Thu Dec 24, 2020 8:40 am Post subject: Re: Treatment of edges of repair panels welded into pan |
|
|
I load up the areas with master series on both sides. Then epoxy prime. When I did my floor pans I didn’t bother doing seam sealer either. I used a lot of master series and then bed liner. |
|
Back to top |
|
 |
67ctbug Samba Member

Joined: January 24, 2016 Posts: 3280 Location: CT
|
Posted: Thu Dec 24, 2020 10:57 am Post subject: Re: Treatment of edges of repair panels welded into pan |
|
|
Grind the edges, master series, seam sealer both sides, then paint. _________________ '67 Beetle L41
'71 Westfalia (sold)
'71 Westfalia (sold)
'74 Westfalia
‘69 Plymouth
Go Cubs!
World Series Champions 2016
KentPS wrote: |
...or the PO envied the terrorists' bus in "Back to the Future".  |
mukluk wrote: |
He's fine, just waiting for the dragon in winklepickers to move out of his lane. |
|
|
Back to top |
|
 |
anthracitedub Samba Member
Joined: June 20, 2007 Posts: 3150 Location: Michigan
|
Posted: Thu Dec 24, 2020 11:09 am Post subject: Re: Treatment of edges of repair panels welded into pan |
|
|
POR patch is some great product for this as well. Comes in a tube, squeezes out like paste and you can finger it (wear gloves) or brush it on each side of the seam. Drys harder than mummy’s nuts yet remains a bit flexible. Has a hundred different uses as well. |
|
Back to top |
|
 |
Weezle Samba Member

Joined: February 07, 2014 Posts: 491 Location: ORLANDO
|
Posted: Sun Dec 27, 2020 8:29 pm Post subject: Re: Treatment of edges of repair panels welded into pan |
|
|
thank you very much each of you for your replies, very helpful!! and appreciated. Im just waiting for another quart of master series primer. That stuff hardens in a few days once you open it. It is pretty bullet proof on whatever you paint it on however. Once the welded in sections and seams are re-primed I will seam seal and put a couple coats of herculiner on the bottom. The top will have sound deadener. thanks again. _________________ Run Forrest, Run!
http://www.thesamba.com/vw/forum/viewtopic.php?t=604918&postdays=0&postorder=asc&start=0 |
|
Back to top |
|
 |
|