| Author |
Message |
DanM Samba Member

Joined: June 07, 2002 Posts: 1389 Location: Falls Church, VA
|
Posted: Sat Mar 29, 2025 11:09 am Post subject: Re: New Delrin Shift Rod Bushing |
|
|
| I've been sitting on a Washburn delrin shift rod bushing for a while - decided to rip out my WW bushing today to "upgrade" and as stated by others here, this new delrin one doesn't fit. I didn't look for feedback before buying but here we are - same problem as the others - not deep enough to "click" into place. |
|
| Back to top |
|
 |
MajorPIle Samba Member
Joined: February 15, 2021 Posts: 20 Location: CA
|
Posted: Sat Apr 26, 2025 2:44 pm Post subject: Re: New Delrin Shift Rod Bushing |
|
|
I cannot get the shift rod through the Delrin bushing. 1970 Bug Standard.
Any tips or ideas? Even if I can get it through I'm worried it will be way too tight for the shift rod to even move.
I've sanded down the shift rod remove rust and dirt and I've tried spraying wd 40 while trying to push it through.
Any advice?
Update: I just used a caliper and the inside of the bushing when in the hanger is 21mm and the shift rod itself is 22mm even at the point closest to the shifter. |
|
| Back to top |
|
 |
jpaull Samba Member

Joined: February 22, 2005 Posts: 3682 Location: Paradise, Ca
|
Posted: Sat Apr 26, 2025 6:23 pm Post subject: Re: New Delrin Shift Rod Bushing |
|
|
| MajorPIle wrote: |
I cannot get the shift rod through the Delrin bushing. 1970 Bug Standard.
Any tips or ideas? Even if I can get it through I'm worried it will be way too tight for the shift rod to even move.
I've sanded down the shift rod remove rust and dirt and I've tried spraying wd 40 while trying to push it through.
Any advice?
Update: I just used a caliper and the inside of the bushing when in the hanger is 21mm and the shift rod itself is 22mm even at the point closest to the shifter. |
If it was machined wrong, and the id is too small, advise is a email to the seller. They should not be letting those out the door |
|
| Back to top |
|
 |
chrisflstf Samba Member

Joined: February 10, 2004 Posts: 4246 Location: San Diego
|
Posted: Sat Apr 26, 2025 7:23 pm Post subject: Re: New Delrin Shift Rod Bushing |
|
|
| The bushing has a split in it, so you cant measure its ID in the bracket. The rod will expand the split, when installed. Just like a factory bushing |
|
| Back to top |
|
 |
clockworkbox Samba Member

Joined: July 12, 2020 Posts: 483 Location: Williamsport, PA
|
Posted: Thu May 15, 2025 8:00 am Post subject: Re: New Delrin Shift Rod Bushing |
|
|
The guy who sold the bronze bushing and switched to Delrin isn't selling either bushing now. I wonder why...
As of May 12, 2025 we have discontinued offering the Custom VW Shift Rod Bushing. Thank you to all of those who purchased and used our custom bushings. _________________ '69 Beetle (pieces)
Learning the hard way is still learning... |
|
| Back to top |
|
 |
EVfun  Samba Member

Joined: April 01, 2012 Posts: 6380 Location: Seattle
|
Posted: Sat May 17, 2025 2:09 pm Post subject: Re: New Delrin Shift Rod Bushing |
|
|
I think Washburns is still selling the snap in Delrin bushing and CIP is still selling the 2 piece bushing held in by one of the shifter bolts. (Likely other sources for both, that was a quick search.) The metal bushing being modified for a snap ring is a Hillman 882999. VW used a metal bushing until 1960. _________________
| Wildthings wrote: |
| As a general rule, cheap parts are the most expensive parts you can buy. |
|
|
| Back to top |
|
 |
Cusser Samba Member

Joined: October 02, 2006 Posts: 33510 Location: Hot Arizona
|
|
| Back to top |
|
 |
vamram  Samba Member

Joined: March 08, 2012 Posts: 8248 Location: NOVA
|
Posted: Sat May 17, 2025 6:32 pm Post subject: Re: New Delrin Shift Rod Bushing |
|
|
I've had the CIP1 split red one on my daily driver '73 Super for 18 months now. So far, so good, perfect feel to the shifter. And Super easy to install!
_________________ "Men are qualified for civil liberty in exact proportion to their disposition
to put moral chains upon their own appetites. -Edmund Burke
'74 Super 9/16 - present, in refurb process.
'73 Super - 6/18 - Present - Daily Driver!
'75 Super Le Grande...we hardly knew ye. Sold 2025 for peanuts.
Click to view image
Save the Supers!! |
|
| Back to top |
|
 |
H2OSB Samba Member
Joined: April 14, 2013 Posts: 1560 Location: Modesto, CA
|
Posted: Sat May 17, 2025 7:07 pm Post subject: Re: New Delrin Shift Rod Bushing |
|
|
I have the Washburn one. No issues.
H2OSB _________________ (o\_i_/o) Funny thing about pigs, they're cleaner than you and me. Well....you. |
|
| Back to top |
|
 |
|